2010 iMac 27" Damaged Display LVDS Connector replacement.
Vložit
- čas přidán 29. 08. 2024
- ⭕ Ask questions and Engage in our Forum at northridgefix....
⭕ Need a repair? northridgefix.c...
⭕ Visit our ecommerce shop and buy all your tools at northridgefix.com
⭕ We are an Amtech Flux Distributor. Buy AMTECH NC-559-V2-TF Flux
northridgefix....
Microscope northridgefix....
UNI-T UTi260B thermal Camera
northridgefix....
Grinding pen
northridgefix....
Low Melt Solder
northridgefix....
NorthridgeFix T-shirts
northridgefix....
Weller Soldering station ebay.us/1mvgt5
=================================================== If you are local, drop in and say hello
NorthridgeFix
19365 Business Center Drive, Unit 7
Northridge, CA 91324
Phone: 818-668-7058
NorthridgeFix.com
For me looks like he ripped the connector off the board while removing the screen and then he opened it and applied some solder on the connector without noticing that all the pins where destroyed. Probably someone without knowledge. By the way as always amazing video, all clear and concise. I love how clean you are. Thank you for sharing with all of us.
This video was fascinating and I'm in awe of your talents. I've not seen anyone get right on the board and fix it. Everyone seems to just swap boards to do a fix. Thank you for putting this up I'm a fan.
Yep, fan right here too
Thank you SO much!!
I’m a total amateur in board repair (I swapped a micro USB cellphone connector once and a bios chip) and this time, a friend came to me with a total messed imac connector with broken pads and some scratched pads that solder was merging on board! I could manage to fix the pads with some overcoat pen and jumper wires. Gosh that was something xD
But I succeeded and let me say “THANK YOU!”.
Great videos by the way. Always a pleasure to watch you. Have a great day!
Thank you so much for this video. You gave me the confidence to repair my Dad's Imac that I damaged the LVDS connector on when upgrading the CPU. I nearly cried. Without your help I would have never even dared let alone achieved this component replacement. Imac works fine again. Who knew about low melt solder!? Next GPU upgrade lol! I love you man.. I hope your children marry into royalty! xx
Another good lesson. I tried soldering a connector a few days ago, and it constantly create bridges between some pins. After seeing what you said, I've got back to that connector and checked, and internally, the pins that create thoss bridges are connected between them. So, no more worries with that, and everything is working. Thanks again!
Big boss never talks, but can talk with his mind to power iMac on!
:-). That's very true.
your videos shows the clear difference between professionals and ... no words for who soldered that connector before you.
اساس النجاح ان تتقن عملك سلمت الايادي استاذنا الغالي وانت يا خال العزيز
يسعدلي صباحك استاذي الكريم معلومه مهمه والاهم طريقتك يامعلم في لحام الكونكتر صدقا شغل هندسه
بارك الله فيك أخي سلمان
Hi Mr.NorthridgeFix watching your videos and learn so many thing. i have a question that you did so many hard repair project so far
' so which one is your hard project so far please tell us. from Pakistan.
Very satisfying to see a computer boot up after working on it
Sir.. you are HERO..
Wow I always learn something new from your vids. It’s great n thanks for all your informations n knowledge mate. You actually help build a lot of faith through your work.
Excellent! Just for info, if the volume is muted when the Mac is powered off, the startup chime does not sound when it is powered back on. I find the chime irritating, so keep my volume muted before switching off every night.
Good work.
You guys are next level!
very nice job! Thanks for sharing!
Great job!!!! I would like to reach somebody here at Cancun Mexico doing this.....I have that same issue .
Wow that is a pretty cool liquid great video
Northridgefix💪💪💪
I enjoy the videos...very entertaining... thanks for sharing
i was thinking that last test pin by pin was not necessary . but after second i answer myself that's the deferent between a regular work and a perfection work
Great job again like always
Love the way u work$$$
You are a pro welding
Pro !
Those 2010 LVDS connectors are fragile, easily ripped off because the cable is very short and getting to it to disconnect is not easy. So is the 2011 one which is smaller and even more fragile. There's a stand locker or whatever it's called that stops the whole thing swivelling on the stand, then laying the computer horizontally so easier to work on.
Does it make more sense to solder two end legs first so it will stay in place?
No it doesn't
Great unintentional ASMR. Excellent tech skills too!
Good job!
Your video shows an excellent way to repair the connector. However, when I removed the base connector about three of the pins broke off and went somewhere into the body. Any advise on how to fix this? Thanks.
same. they very fragile.
Awesome
Hola amigo haces servicios fuera de Estados Unidos?
Tengo mi iMac late 2012 con el mismo problema de tu vídeo el conector lvds se arrancó de la placa madre , ya lo lleve a un técnico , El lo reparo y no es profesional por lo que aún sigue sin funcionar mi iMac es de 40 pines , alguna recomendación? O podría hacerlo yo mismo talvez?
clean excellent job..
thank sr
Damned lucky the pins on the connector broke rather than ripping multiple pads off the board!
Thank you. This is my exact problem:-)
What's it mean if there are no diagnostic led lit on late 2009 imac, but the fans come on and the boot chime is heard? The guy i bought it from ripped out the LVDS connector. I replaced it with a salvaged one, but no go. I'll remove it and try with a new part. Meanwhile, with no screen or cable attached, what's up with the missing LED status? I also noticed that there is no voltage coming out of the pins for the backlight, but there is 12 volts coming into the backlight board. If the vertical sync cable is not in (the screen is not installed when I am checking these voltage points), will the back light voltage be affected? That would not make sense. Just looking for clues.
Excellent
Alex where did u get those two steady hands of yours from
better soldering than the factory :)
Hi, do you know where I can get replacement TFT, IPS, OLED, AMOLED for broken TVs. I would appreaciate your Ideas.
very good
I have an imac 5k with sever ghosting. it drives me mad. i want to replace the screen but if i get you to put in a new screen will the new screen eventually ghost as well?
How do you change angels from different camera? Via post edit? Or via software
Thank's for video...it's help me a lat:)
good job thanks
Thank u very much
do you guys someone that can do this in the UK... I'm in London and I have a imac 2009 27 with the same problem
How do you know for sure the pins are bridged together without a diagram? Is it just because you are unable to separate them when solder flows?
I have this same problem. 2010 27” LCD cable connector is broken on the board. What I am also dealing with is the connection is also broken on the lcd screen also. Is this fixable?
Is one of the visual artifacts of a bad LVDS black, black vertical bands on the screen? I sent my 2012 iMac out for repair here in Kathmandu Nepal, and it came back that way. I don't want to send back to the same shop... what to do? thx!
I have an imac 2010 27 ", which the display turns off but the equipment is still working, I changed the inverter card and it worked for a couple of weeks, but the same problem came back, what do you think the problem is? thanks
thankssss
Do you put tape over the connection after pluging it into the board?
What flux are you using
What solder did you use or would you recommend?
Cheers 🍻
Machallah bro good job
I see JAE in the connector. Maybe it is made in philippines in JAE
Can a worn-out LVDS connector cause severe ghosting on my iMac?
What is the liquid you use for solding?
Hey I have the same problem with my mac 27'' but there are 4 connectors for the display instead of one and 2 out of the 4 connectors are broken off I don't know what they are called or where I can find replacement parts pls help.
Niss vdo
We all want to see bigboss dancing again
Alt yazı seçenekleri ni açar mısınız? Harika olur
Que herramientas usaste ?
What brand wick are you using in this video?
It's exactly m'y problèm but could Never do all you do.
هلا كيفك يا عم حسن ان شاء الله انك بخير ممكن تعطي لنا قائمة لادواتك واسعارها
إنشاءالله
hello sir what is your solder station?
What is your lense camera price
What flux do you use?
rover.ebay.com/rover/1/711-53200-19255-0/1?mpre=https%3A%2F%2Fwww.ebay.com%2Fsch%2Fi.html%3F_from%3DR40%26_trksid%3Dm570.l1313%26_nkw%3Damtech%2Bv2%26_sacat%3D0&campid=5338440312&toolid=20008
what is that gel?
That is flux, which causes the solder to flow.
Mano você é o cara !
لك مني احلى sub
Hello friend, do you serve outside the United States? I have my iMac late 2012 with the same problem of your video the lvds connector was ripped from the motherboard, I already took it to a technician, He repaired it and it is not professional so my iMac is still not working with 40 pins, Any recommendation? Or could I do it myself maybe? Please help me
Fill out the mail-in form and send it in northridgefix.com/mail-in/
Can you please tell me what program I can take in school to learn how To repair items like you do ? Thanks
electronics buddy. but no program will teach you how to repair boards but once you learn basics and advanced principles of electronics, components, and how they works you can work with some repairman to learn some professional knowledge. Than you can fix like this guy. Fixing needs experience or knowlegde from someone who is experienced..
Assalam walekum
nice jumb.more video please
maybe its Gossip . and its not about Job s but. i noticed some times spoke Arabic . what the big boss come frome . dont answer if u don't wants 😁
Those 4 pins at ( 14:55 )were not supposed to be toguether, check carefully from 7:10 to 8:30. You used to much solder. You no good my friend...not even using a telescope.
I will never take my imac to his place...😁😆
then how come the lcd fixed?
You are correct. those pins were not connected together
Surprised it worked!
@@wahabfiles6260 Luck
There is a trace connecting the two pins in two cases on this connector, and if ANYONE knows how much solder to use, it is Hussein Ali.
Do you know the muffin man
why *big boss* is just a cameo?
This guy has very rough hands
You use a lot of flux...