DIY - Hurricane Shutter Install
Vložit
- čas přidán 23. 04. 2020
- While having lots of time on my hands during the Covid-19 pandemic, I take the time and invest it into my house by installing Hurricane Shutters!
My house is a 1985 vintage house with single pane crank-out jealousy windows. Living on the Gulf side of Florida where Hurricanes come occasionally, we felt very vulnerable to one doing serious damage to our house. So I got a quote to replace all the sliders and windows with hurricane rated ones at it was $85,000 - waaaay too much for us to afford!!
After researching different hurricane shutters commercially available on the market, I chose the Storm-Busters Clearview poly-carbonate panels that you can install yourself. These are 80% lighter than a piece of 5/8" plywood, are UV protected, are Florida hurricane rated, and allow light into your house when installed!!
In this video I show how I installed these panels so that they are nearly invisible when installed allowing them to be left up indefinitely if desired! Although the manufacture suggests that you make the panels much larger and bolt them into the brick work around the window, I found it much better to cut them much smaller and directly affix them to the aluminum metal frame of the window. The way I did it makes them almost invisible when viewed from the outside which we like best.
We would greatly appreciate your support by using the link below for all your future Amazon.com purchases. It will be totally transparent to your Amazon shopping, and doesn’t cost you a thing!
amzn.to/2HZTbZA
#StormBusters #clearview #Hurricane #Florida #DYI - Jak na to + styl
This is so awesome! I really like that you can put them on, leave and not worry if you can make back home if you’re traveling! I had the same issue with the cost of hurricane windows. You’re either an engineer or just incredibly smart! I’m doing this. Thanks for a great video!😊
Beautiful work. Your reasoning for putting them against the window is sound. The purpose is to keep the wind out. Glass is easily replaceable. Your video was very helpful to me. Thank you.
Very helpful video. Thanks for sharing 👍
Thank you for sharing that in details! 😃
Great video. I’m going to try this. Thanks.
Great video, thank you for sharing, you did a really neat job and have given us some good ideas :)
I don't usually comment on CZcams---but You're awesome! Thanks!
Congrats on the great video and instructions! Could you advise why did you decided to mount the panels to the windows and not the house concrete? I would think that keeping a distance in between the panel and the window might help in case of any flying object hits the panel directly. Thanks again for the great video 👍🏼
My 76 year old Florida house had those original ja-lousy windows my first year living in it. I wondered the how it survived all the storms (and cold fronts)through the years. My Lowes has these panels now and will get these.
Great video. I really like this method. Do you know if there has been any projectile impact testing done?
Why did you screw it in your window frame when it rains the water will get in from the moisture and rotten the window. You should of cut it 2 inches less from right to left and screw it to your concrete block way better. Otherwise awesome video.!!!!!
He screwed into aluminum.
Very nice presentation Charles. As our windows are not recessed and actually protrude a bit out from the trim, this would unfortunately not work for us. But I did enjoy your well done video. Thank you.
This is better than the how to video by the company that sells these.
A very informative clip, Mr. Coushaine giving individuals inspiration and confidence to maintain their homes. You remind me of my husband who recently died, high quality craftsmanship, always. I stumbled on your video while searching for shutter options other than heavy corrugated metal, in an attempt to make my home more manageable for me. Do you think Storm-buster polycarbonate shutters would utilize the existing hardware that is in the concrete window frame?
Good stuff
My older home came with 5/8 plywood shutters. They were terribly heavy and once up the house was like a morgue inside it was so dark. So, I DIY'd polycarbonate replacements. They are lite, stronger than plywood and let lots of light in. I'm 71 and I can lift them right up the ladder to the 2nd floor and I cannot do that any longer with plywood - and the poly won't rot. If I'm too busy I can leave the poly up whereas the plywood is really terrible looking. The expensive hurricane windows may pass the cannon test but the glass actually shatters and the window needs to be replaced. I think these are the best shutters available and even beat the very expensive hurricane windows.
Thank you for taking the time to make this video! I was just at lowes the other day looking at the same panels as you have but I didn't understand how to install it. As I'm watching your video, the only thing I'm not understanding is what are you screwing the screws to? On the stucco or the windows? You can come over and do mine anytime!😁
Tamara D Campbell it appears the window frame, maybe the outside edge where it meets the stucco.
I really think it looks much better than hardware in the bricks but unless you are leaving these up 12 months a year doesn't it wreck your windows? Or do you place something in the holes when you take it down.
Very Nice. How much did you spend on buying the panels? Where did you buy the panels from? Thanks
The 4" x 8" panels and aluminum H-connectors came from Lowe's. The panels were about $90 apiece.
Which screws did you use? We can put them on the crank windows we never open.
HI, what is the force of impact they can withstand?
My question is one of permits and certification.
If I install theses myself (in Florida), any home buyer will want it to be permitted, etc.
The instructions state to mount on the outside of the window, overlapping 4". Was this to save material mounting inside of the frame?
yea same question here. Its very custom what he is doing, idk if its what is ASTM E rated and all the other rating systems these panels are tested for. I'll admit tho, for my home, it takes a hell a lot longer to do things by the instructions (i.e., tapcon screws ever 12 inches) compared to the few screws that seem like more than a foot apart here... so...
Great video and glad you brought to mind hearing and eye protection, but for your own sake keep your fingers away from the saw blade, especially since it was with battery and it looked like your finger was on the trigger. Eeeek!
How did they work during a hurricane? Just experienced Ian at 100mph. Had the aluminum shutters but for our age, it was a horrible job to put up and then take down and store. Considering this but can't find enough testing done and am not sure of the security it will give us.
I was with you in Punta Gorda and Hurricane Ian going right over my house! Lost all the shingles from my roof, lost all my soffits, pool cage got destroyed, however all windows survived perfectly with these panels in place! This was a HUGE success!!!
The video is very informative. I tried to follow the Amazon link to order. Can you please provide the manufacturer information I will order directly from them if I’m not able to order on Amazon. I like the permanent look and the UV protection. Thanks for sharing.
The hurricane panels were purchased from Lowes!
hi; i think 'they' want a 2 to 3 inch clearance in between the window and the Poly, less chance of the glass breaking if struck.
The goal of my installation was not necessarily to stop glass breakage but to prevent debris & wind penetration into the house that ultimately does most of the damage by lifting off your roof!
Hi, how much thickness is it, please.
What did you screw into? The actual window frame?
Yes. The actual window frame on my house is aluminum and quite robust so it accepted the screws perfectly. However, if you want you can extend the length of the panels and screw into the house. I chose the window frame because it kept the pieces quite a bit smaller, and allowed me to leave a few of them up all year long on windows we don't open and the panels are not even noticeable from the street!
Bad idea to put it against your glass as the panel will bow in with a strike or hard winds. That would break your glass instantly. Would leave at least approx. 5" pillow of air between panel and glass.
As you saw in the video some windows based on their design do not allow for a 5" gap as you recommend. However, the goal is to stop the hurricane winds from getting in and doing serious damage - broken glass is easy to fix!
@@chrisloboda7331tensile strength however is probably measured in pull strength, much like tape. Flex strength is entirely different. Very little effort to poke a hole into it but you could hang several pounds from it.
Where I can buy those panels, the Amazon link don’t work, Home Depot have those panels or any local store or online. Please help. Thanks
I believe that I purchased the panels from Lowe's
Where did you pick up the H channels (Aluminum ) ? Thx
Lowes sells them with the hurricane panels!
@@charlescoushaine OK, will check again . they must have been out at my Lowes.
@@charlescoushaine GREAT video by the way .. ***** 5 star
You are amazing, I will do this in my house 👍I which you did this in Spanish 😂🤣😂🤣😂
Sorry to ask but how much you pay for everything? 🤗
You can go to the Lowes website and they have the info you need.
Rene Borroto ohh! Thank you, I did but whit the aluminum shutters. I can’t figured out how to do it like this, I’m a single mother, so I do all this projects by my self 😂🤣😂🤣😂 but thank you, you are very nice .
lili lili you’re very welcome!
Thanks for sharing this video!! I saw these panels for the first time today (Lowe's website). I live in South Florida and face similar issues as you, except our house was built in the 60s. I had made removable plywood panels to fit inside the window frames like you did, but they're heavy and ugly. Any reason (besides ease and aesthetics) that you chose to screw the panels to the window frames rather than the concrete area around each window (as recommended by mfg)? I realize your method looks better and avoids all the drilling into concrete block, but I'm concerned about winds causing the panels to flex during heavy winds and breaking the windows. Again, I think your video and these panels are TERRIFIC.
Hello Rene! I chose to attach the panels to the actual window frame for multiple reasons. First, as you guessed, I did not want to drill into the cement and leave studs sticking out when the panels are removed (ascetics), and also several of my windows were not recessed, and I couldn't attach anywhere except the frame! My goal was to make the most ascetic looking protection such that I could have them up, and from the street, you could not notice them so that people would know we were away up North! I do not believe that flexing from wind would ever break the windows, however, an impact from something could flex it and break the window but the surrounding frame should adequately support the panel such that it does not breach and compromise the inside of my house! No matter what, I feel that my house is much more protected then ever before, and we plan on leaving several of these panels up year round (on non-opening windows) since they are so 'invisible' from both the inside and outside!
@@charlescoushaine I'm leaning on using your system of attaching the panels to the window frames. Having all those bolts sticking out around the windows does not appeal to me, and you're not really sacrificing safety by using the window frame. We have several windows that we never open, and so the panels would probably stay on there year 'round. Thanks again!
I currently use plywood and secure them using plylox clips, would be nice if they made a clip for these sheets.
Here we go again......exterior stucco or wood frame or brick construction. Most new homes are vinyl sided and also may have vinyl-framed windows..... don't seem to see many ( any ! ) DIY for that type of construction...... there doesn't seem to be a good "place" to mount...especially since a lot of these homes also have "decorative" shutters....
that's not the recommended way to mount the polycarbonate
And where did you buy the panels and how much are they?
I purchased the panels from Lowes.
@@charlescoushaine thank you for replying!!! I’m going to get them. Question: as you’ve installed yours right up against the windows , are you concerned that if something hits them at 150mph it may flex the storm shield enough to break the touching window it’s protecting?
@@stevesantagati7265 Although I would prefer an impact to not break the window, my main goal here is to stop impacts from breaking thru and the resulting wind blowing thru and doing extensive harm to my house, like blowing the roof off! I can always fix a broken window easily after the storm, but stopping the impact from breaking thru is my main goal with these panels!
It does not appear you have a detailed explanation of how you screw them in. There are many ways that can be accomplished with varying results. Please show this in detail with close-up imagery to explain how they are secured on the regular windows.
Every installation will vary slightly depending on your windows. Mine were older 1985 vintage with complete aluminum frames. I used stainless steel screw right into the aluminum frames and this has held up great for years! If I was screwing into wood or brick I would use an alternative attachment method appropriate to the material screwing into.
Where did you buy the Panel?
I saw these at lowes yesterday
$85,000 for impact windows? Do you have close to 85 windows or something? Thought they were on average $1,000 each window. Maybe a speako (spoken typo) for $8,500?
Nope, it was a quote for $85,000 to which they gave some discounts...but not nearly enough! And, they we quite mad that I didn't know it would be that much!!
@@BrettB246 yea man, they are mad because you didn't go their way. Can't believe they tried to sell you that high amount for windows... ridiculous.
where did you buy it?
They sell them at Lowes
Lowes
Thanks
$85,000🤔
You could use these clamps instead of drilling holes to the frames (your windows will corrode very quick)
czcams.com/video/HNnvaAp7Bww/video.html
Thanks for the suggestion however although it works great on ridged plywood I don't believe it would work on these much more flexible polycarbonate panels.
Not Shutters. Panels DA!