Rolling & Pulling Fenders on my 2014 Mustang!
Vložit
- čas přidán 12. 06. 2021
- Fender Rolling on 2014 Mustang.
Although in the end I am still rubbing slightly on the passenger side, I'll need an adjustable panhard bar to re-center my rear end and hopefully that'll correct the rubbing issue.
Instagram:TDurrgt
Snapchat:TDurr9
Like,Comment,Subscribe!
#Fenderrolling #Mustang #Tdurrgt @2.8kSubs!
----------------------------------------------------------------------------------
Beats by instagram:1datboylu - Auta a dopravní prostředky
I feel you. Ima start uploading the video we both needed to 😆 love the V and content
Got 295/35/20 and it rubs on big bumps, had Steeda springs then put roush springs in the back to raise it up 3/4 of an inch. It helped but liked the Steeda look better. Thank you for the video man!
Rev matching on point sir! I'm a newbie at that. Beautiful car, I wanted that color but it's rare...
Also,, mad props on the white tape
I got the sr springs. I can get two fingers on Kong. He sits pretty low. I have the nittos on mine and they are little stretch. And they hook harder than my other 305 .
Good shit posting this video💪💪fenders STAY rubbing same deal on the high way bumps
This actually helped my rubbing issues even tho at the end those digs showed opposite. Haven’t been rubbing at all really since.
I wished he rolled them a bit taller to make that one line instead of two…
I’m rolling one in a few hours and I’m glad to see this video AND your comment. I definitely don’t consider this a good pull.
Sadly you can’t roll “higher” won’t help. That crease comes from where the inner liner meets the outter panel. No way to avoid it sadly.
Welp let’s hope this makes running 284/45r20s possible
Do you have a Adjustable Panhard Bar? Might be able to split the difference but won't be much. I want to get my rear fenders done as well
Nah I still don’t have one
The fenders are mostly rolled from factory
Damn, when I get a new car I want to run big tires. So I will need to roll mine as well.
Not necessarily. It all depends on your setup from lowering to wheel specs. I have a 305/35/20, but if I’d gotten a 305/30/20, I would have been fine no rub..
@@Tdurrgt Ahhh ok. But I drive crazy and always trying to race people lool.
Bruhhhhhh you doing pulls with a gas light on??? You got bawlzzzzz
What’s wrong with that lol
This video is definitely helpful. I'll be looking into the 305/30/20 soon. By the way, what's your exhaust setup and tune? Those down shifts sound so good.
Hi-flow cats to a 3” xpipe to a resonator delete, muffler delete. Lund 93 tune. Previous vid has all my mods if you wanna check that out!
I have the same lowering springs as you with 305 45 mickey thompsons in the rear and don’t rub at all, maybe try a different offset on the wheels
What size is your rim tho? Maybe 17 18? And I wouldn’t give up these wheels 😭
@@Tdurrgt I’m running VMS 17 inch wheels 😂, I also have 19’ gt500 wheels in the rear with a 305/35 and it barleyyyy rubs with highway bumps like yours
@@Tdurrgt I knew if I got 20’s it was gonna rub like crazy that’s why I went with 19’s. I like the meaty look on my s197
Yea the wheel specs just play a role. 19” tire you’d be safe on a 305 forsure. But the 20” I got on the 305/35, 2” drop in rear is a nope👎🏽
@@Tdurrgt yeah, looks good as hell tho man. Props 👍🏻🔥
Man.. be ready for some paint bubbles in the future. That paint, unlike your bumpers doesnt have flex additives in it. Should've got some smaller tires and sold the other ones used
Didn’t think of that honestly but would make sense for the long term. Has that happened to you before?
@@Tdurrgt a friend of mine did it to his sn95, took about 8 months to start bubbling. The paint/metal is also much older. If it happens, youll want to get it fixed asap. The fenders can still stay pulled, and all they'll have to do is sand, prep and then paint/blend. Wouldnt cost a ton to fix unless theres rust
So going a smaller tire is better? Mine is rubbing aswell, not too bad but i wanted to roll my fenders.
Hmm. That is an older car so that plays a factor into that and if there was any rust forming before hand. However though, if that does happen to mine I’d say it can take some years. But thanks for the notice forsure ✅
@@jevaughn34 yeah either 305/30s or if you want thicker, 285/35 or /40. Honestly anything above 285 on a hard street tire isnt doing much for you anyway
What make/model and size rims do you have?
Sve series 3 Gunmetal 20”
Who’s the guy that you found to do it?
Check marketplace. Should be under fender rolling in Romeoville. If not...
Underground Autosports in Hoffman Estates rolls fenders to. I ended up going here and they did a great job.
Also, just raise the rear a quarter inch and you’ll be fine
How so though?
Looks bad in my opinion
Not too bad. Can barley notice that my fenders are pulled unless you get up really close 🔍
Hey yougan it's the old man. You need to stop making bluedini squatting down shitting on them Hemi's😄😁😆😅
Mann we gotta show these mopars who run the town💪🏽