Taking Apart Canon MG6320 Printer for Parts or Repair
Vložit
- čas přidán 4. 07. 2024
- This is a Canon Pixma MG6320 all in one printer which we are pulling parts from. It is a great printer, so if this video helps you fix your printer, I hope this video helps.
A thumbs up is greatly appreciated!
Please don't forget to subscribe @303electronics
Have a great day!
303 Electronics - eBay - printer parts and printers store.
www.ebay.com/str/303electronics
www.303electronics.com - Věda a technologie
Looking forward to the reassembly video ;-)
I hope there is a specific decomposition video of the waste ink line.
All I wanted to do is clear a paper jam. It's under that big black panel on the bottom but I cannot get it off.
What to do for a paper jam inside the printer?
just got my MG6350 working again, didn't get past Error code 5200, not sure of original problem but once i ripped the side off and check all the cables to the PCB it started working again, nothing even look loose.
Glad it started working, thanks for sharing! Good work! Have a great weekend!
have the exact printer but its mg7570, but i says cpuld not detect ampunt of ink on cartridge. 2 of them. and ty
I have a message "Ink absorber is full", but no explanation it is. Video clips are for other models that are completely different from MG6320. Can you help me, please? Thanks a lot
Hi. I understand why instructions may be different since this printer model has a touch sensitive control panel rather than the actual pressing buttons. I do not know how to reset it, but will update this answer if I find help for you after some research. I apologize for not being very helpful at the moment.
Hi, thank you for the video- I am having issues with the output tray not opening automatically. It gets stuck and I have to manually force it open. It also won’t close all the way.
Does this mean I need to replace the output tray? And if so, do you have a video on how to install the tray? I can’t seem to find one.
Not necessarily. You can check the tab on the right and make sure it is on the correct position. You may remove the tray and reinstall it properly, but I doubt you need a new tray.
Hi thank you for the response. I have removed it according to your directions but the small tab that’s supposed to open when the tray opens is not moving with the white piece. How do I connect the two?
Thank you very much. I followed your video and was able to clean my timing strip. Unfortunately I had also to remove the upper metal rail of the print head carrier. Do you have a video how to correctly remount it so that the print head is leveled again and the alignment is correct? Thanks a lot. Please need your help.
Hi. I have a similar model on which I'll try to show that. I'm sorry it took me a while to reply. First had to check if I have one.
Hi. Just posted this video on replacing carrier. I hope it helps:
czcams.com/video/3Q0zDfq9E7Q/video.html
@@303electronics t
Do u know how to send this printer into service mode? Thanks.
wondering the same
I have a MG7770 but I lost which wire goes where to the main board. Does anyone have a photo I can refer to? There's two types of 4 pin connectors one white and orange and I can't tell which goes where since they are close enough to plug into either and are both 4 pins. Any help would be greatly appreciated. Thanks!
Most wires should be different and one will not fit into the wrong slot. The printhead wires are same, but are in order and shouldnt cause confusion. I know it is a bit of a complicated job.
Hi is there a way to get into the absorber pad in a simpler way?
I am not sure, but possibly there is an easier way. I will look into that and let you know,
Hi, is there any possible open the body without open the scanner? . coz only need replace ink tank waste pad
You don't need to remove the scanner, just skip to removing to portion.
@@303electronics okay thanks for your advice 🤗
I have a similar printer and it doesn’t turn on. Any ideas on what could be wrong?
It can either be a bad printhead, main board, or a power supply that shorted your printer. Try removing the printhead if possible and then turn printer on. Sometimes.
@@303electronics thank you, I will try that.