Restoration old suzuki 110 engine | Restore and repair old suzuki 110 engine
Vložit
- čas přidán 28. 04. 2022
- Restoration old suzuki 110 engine | Restore and repair old suzuki 110 engine
I hope you find something useful from this video!
I am very happy to receive your feedback, advice and suggestions to improve myself more and more
!!! I apologize for the mistake if I did in this restore!!! Thank you for watching the video have a good day. Don't forget to like and subscribe to the channel
Link subscriber
/ restorationittool
Link facebook
profile.php?...
Link twitter
/ mrthao18
#restoration #engine #suzuki - Věda a technologie
You did a good job! I have a few tips to help you that I've gathered over the years.
I'd take the large bolts out of the engine side covers before you repaint the covers, wire wheel the bolts, and then reinstall them. It makes your work look better.
Don't reuse removed bearings if you can help it. Removing them damages them.
When you install bearings, it helps if you freeze them for a while, and heat up the case they are going into. Usually, they fall right in, and that doesn't stress the case or bearing. If they don't go right in, gently hammer them in on the outer race of the bearing.
Using the same technique, assemble everything but the crank into the center cases. Put the crank in the freezer for a while. Heat both the crank bearings after they are in the cases, and install the crank and the other case half on the first case half before the crank loses it's cool, and the bearings lose it's heat. Hammering on the crank could wreck it's trueness.
I like to put loctite on the kick starter pawl screws, shift drum bearing retainer screws, shift star bolt, shift star stopper bolt, stator screws, and neutral switch screws, to keep them from falling out.
Put oil on every part that slides or rotates as you assemble.
I like to replace clips and bend-over tabs when I assemble an engine. I've seen used ones fail, and cause massive damage!
Did you size your new rings for your new bore? For a naturally asperated engine, 0.004 inches of clearance per inch of bore, or 0.1mm per 25.4mm of bore is good.
You didn't put a used oil filter in there, did you?
Is there any reason you didn't repaint the oil filter cover?
Hope this helped, and keep up the good work!
Ppl
@Nun YaBizzness I agree with you on all points !!! ALWAYS use NEW bearings and Simmerings and seals !! And the OLD oil filter needs to be replaced too! Well at least the piston and the rings are new as it looks. ☝☝☝
សុំHonda 125cc thengyou
Good job,returning a machine that was not in good condition to normal again
Запресовка подшипника коленвала была произведена с нарушениями. Прессовать нужно было по внешнему кольцу а вы били по внутреннему, тем самым ломая сам подшипник.
Good job 👍👍👍Thank you for sharing. Be safe
semangat kaka💪💪💪
Đồ suzuki thật sự quá chất lượng , làm chắc chắn 👍
great job👍👍
Using old bearings and hammering on inner race is no bueno....
i guess not all have budget to fully restore things
👍👍👍👍
good job paman
good stuff that has been rusted so it's good again👍
As you can see in the video, we have restored the machine to normal operation
Nice dry steels and frictions but the best is the smashed head gotta love the valve head falling off
حلو أستمر حبي 🤩😘😗
Restauração que não se vê a todos momentos parabéns 🇧🇷
Why not wash the exterior of the engine first, before disassembly, using water and dish washing liquid? That would also be a lot safer for the surface finish compared to using a wire brush... And, only drive a bearing into the casing using a socket of the right size to ensure that you are applying force on the OUTER bearing race only. When you are striking on the inner race, the inner race takes the hit and has to transfer it to the bearing balls which in turn transfer it to the OUTER race. No reason to stress all of these items...
You’re absolutely right, I couldn’t have said it better myself.
Very good
restauraion y puesta en marcha muy bien master!!!
Zữn thì sữa chạy được chớ hết vọc rồi không có ngon như mới nó hết hơi
Gila jago banget ente bang... Skill nya ok banget 👍👍👍👍👍
Bine lucrat!!!...like👍👍
Ótimo trabalho
Sois maravillosos muy buen trabajo 👍
Los rodamientos o rulemanes no se colocan a los golpes y menos el cigueñal (se colocan con calor), no le cambiaste la biela ni los rodamientos,
Despues el resto muy buen trabajo
جميل جدا good
Kindly use new bearings and install them using press machine, try to avoid hammer while installing them. ✌✌✌
thank you
7i89😊😊
Trabalho Top parabéns 👍👍🇧🇷
Estão de parabéns ótimo servicos!
thank you
Bon travail .
cái này chắc làm để làm cái video thôi nhỉ, chứ làm máy thế kia chạy thế nào được?
fine job pal looks and sounds great well done
amazing work, and relaxing to watch.
I think if i were there, I would have started with pressure washing the dirt off the exterior first.
Muito bom !
⭐⭐⭐⭐⭐®️💯 top parabéns 👏👏👏🇧🇷
Wow great nice
deberia de cambiar por nuevos los rodamientos...bearing
FICOU PERFEITO GOSTEI EU JA VI O VIDIO DUAS VESES
What is the solution that is used to clean the parts?
it's citric acid, gasoline and dishwashing liquid
@@restoration-restore-repair Thank you for your quick reply!
Minuto 24:30 faltó un tornillo de el clutch, no causaría problemas en el futuro?
Tengo una suzuki birdie 50cc enciende pero al meter los cambios no tiene fuerza alguien me.puede ayudar🙁🙁
Keren Broow
Thế cũng đòi làm ông đóng cái bạc đạn thế thì hỏng luôn r! Tay biên và gõ thế thì chịu
good work, but I have some ideas. Clean inside out not very clean, old parts ( the bearings,gears, etc..) are not replaced. yes, engine will run but not too long. this is a big time to do and we shoud take it seriously and carefully.
Sand blast the thing.
Mantap
👍
Wow its a suzuki smash engine popular here in Philipines🇵🇭
Quá đỉnh
Honda made the probably most popular design with this one and the GX series. Sooo many copies
Máy su với honda cái nào ngon hơn anh
🦠🦟🦂🕸🕷🦗🐞💐🌸💮🌹🏵💮🌹🥀🌺🌳🌲🌱⚘🌷🌼🌻🌴🌵🌾🌿☘🍀🍁🍃🍂🐊🐸🦜🦚🦩🦉🦢🐢🦎🐍🐲🐉🦕🦖🦈🐡🐠🐟🐬🐋🐳🐙🐚🐌🦋🐛🐜🐝🦠🦟🦂🕸🕷🦗🐞🐭🦛🦏🐘🦒🦙🐫🐁🐀🐹🐹🐰🐇🐿🐿🦔🦨🦦🦥🐼🐨🐻🦇🦘🦡🐾🦃🐔🐓🐣🦆🦅🕊🐧🐦🐥🐤🦮🐕🐶🦧🦍🐒🐵🐈🐱🦝🦊🐺🐩🐕🦺🦄🐎🐴🐆🐅🐯🦁🐷🐄🐃🐂🐮🦓🦌🐖🐗🐽🐏🐑🐐🐪
سبحان الله العظيم...
👍😊
It's SUZUKI BEST 110 cc. it is 2nd models of 4 strokes suzuki behind VIVA > FD LOVE 110 > BEST 110 > SMASH 110 .....etc.
new piston old oil filter ?
still not clean for engine restoration and not detailed in workmanship
nice restoration but where is the bike?
👍👍👍
Bordel catastrophe le mec qui tape à l’intérieur des roulements et en plus sur le vilebrequin et j’en passe
hình như không phải động cơ của viva
No se por que le da golpes a los rodamientos para ponerlos
Чозза движок
SHOGUN GA JAUH BEDA SPT NYA....
ini mesin roso gagah perkasa alias badak
Mesin suzuki shogun 110 di indonesia sama di luar negeri beda ya, perbedaan pada sektor kopling
You miss a 1bolt in the clutch
Hammer kapak
Very wrong with to insert ball bearing.
Открою большой секрет, чтобв помыть двигатель, его не нужно разбирать.
Just replacing all bearing
Shogun 110Cc 2002 engine
😅👍👍
20:40 😂😂😂😂
Ооой, по кв молотком!!😠😠😠
Spilll cattt yang silver pake apa
🇲🇦🇲🇦🇲🇦🇲🇦🇲🇦🇲🇦
Where are you from?
I’m from
Thailand
Làm máy rất tào lao và bẩn, vô trách nhiệm. Làm máy kiểu này làm cho vui thôi.
Very Good
Mantap