Fully restoration old S1100 diesel engine | Restore and repair old rusty Samdi D20 engine
Vložit
- čas přidán 27. 08. 2024
- Fully restoration old S1100 diesel engine | Restore and repair old rusty Samdi D20 engine
Diesel engine D20 uses a 1-piston engine, with a capacity of 14.7 kw, for strong operation, bringing high work efficiency. Along with that is the cylinder capacity up to 1092cc, the number of revolutions of the engine reaches 1500 rpm. The machine works stably for a long time without affecting work efficiency.
I hope you find something useful from this video!
I am happy to receive your feedbacks, advices, suggestions to improve myself better
!!! I apologize for the mistake if I have made in this restoration !!!Thank you for watching the video. Don't forget to like and subscribe to channels
Link subscriber
/ restorationittool
Link facebook
www.facebook.c....
Link twitter
/ mrthao18
#restoration #restore #engine
Ребята обленились, движок из нутри не покрасили, на уазике красили всё, даже свечки, а тут... Ни поршни, ни, форсунки, ни подшипники, совсем плохо. Вот с отработкой - порядок, что слили, в чём мыли, то и залили. Уважаю. Не подвели.
After sourcing new bearings and lovingly restoring this historic engine, why in the hell would you put SHIT for oil in it?
because their is no place to get new oil and its probably expensive
Because it's some excellent engine oil, proofed again and again during countless hours of operation! 😁
No shit !!
simple when you think about it, this restoration was done to make a video for youtube to make money, the engine is likely just put into storage after filming
This awesome restoration work deserves a NEW engine oil.
I feel sick when I see that old and dirty oil being used again.🤢
Get yourself a table!! Makes life a hell of a lot easier.
This guy knows what he is doing
Pouring the used oil back in was the best part!
Отмыли мотор внутри и залили отработку !!! Млять руки оторвать этому ремонтнику!
С чего ты взял?
@@user-ow6eu1dj1v а что не видно? Посмотри 26:15 это явно не новое масло)
@@kaskyrbal8576 можно было и не мыть, там на колене шейка задрана
Amazing, ,
he should have used new engine oil!too bad of the hard work and engine...😔
Hloo
Agreed
Im amazed it started.
Very nice video,
I am amazed at how so much can be done with less than basic hand tools and primitive engineering. Thanks for showing this in such detail.
Y’all see that massive scar on the crank journal where the connecting rod goes? How about that cylinder that didn’t even get a dingle ball hone? A real quality job. Should last a long time. Geez.
The pipe wrench identifies as a torque wrench.
@@christopherbrown8181 ,👍
Well don Restore & Repair.
Super video
Отлично!👍. только нихрена не пойму,зачем отработку заливать в картер?🤔
Другого нет.
Trocar buchas do virabrequim e bronzinas da biela sem ao menos brunir o eixo, além do óleo usado foi o que deixou a desejar. O restante do trabalho está de parabéns.
That sound in the background sounds like a sci-fi TV show or movie.
Nice video like
Всё отлично! Но за грязное масло, ему нет прощения! ))
Я тоже это хотел написать. Всё отлично всё хорошо, но вот это масло портит всё.
@Michele Micheleну всё же там вкладыши
Да согласен стобой
Что там отлично? То что он ржавчину толком не убрал, то что он даже картер не отрихтовал, то что подшипники топором забивал? У меня нет слов...
@@mishkaseverokavkazskiy230 да там посадка "сливовая"...😂
überraschend gut
Putting dirty oil back into the engine no comment Good noise of her changed the oilwell done thank you
I was raised in a time where we worked on old and broken things and you learn alot and do alot with less. Great video--THANKS FROM U S A .
Looks like this chap knows his way around this brand, the hatchet is a tool I’ve never used in engine service, before!
What is truly AMAZING is this jungle mechanic has no problem finding parts for possibly OVER 100 year old utility engine, but I can't find a carburetor for 15 year old Tecumseh.
This is Asia and engine may only be 20-30 years old. The fact that spares were available shows this may be a mass produced little engine fo rwater pumps, rice mills etc.
I bet you could find a litre of new motor oil though!
Топор и разводные ключи🤦🏽♂️ ну и снятие маховика, ударом по носку коленвала, это конечно верх мастерства...
My God all that, new mains, big end bearings, rings .. and no fresh oil !!! Using the old stuff .. 😱😱😱
He had a reason. That man knows his engines.
@@shaenj There is no reason to reuse used, metal-filled, burnt oil....
@@shaenj hij kan niet eens kleppen afstellen!
Old dinosaur oil...help brake in engine lol
Good morning friend, I am touched by your amazing touch👍👏👏
Many things i will have done in a other way, but in the end the result is importent. and it runs nice and smothly for a 1zyl. engine.
most impressiv is the transport, unbelievabel! All thumps up!
❤️
Indonesia present
New friend 🙏🙏🙏
Новые кольца вкладыши,и старое масло🤔...чёртов гений😅..
Работа на отлично👍👍👍
Озвучка адская...
Using the specifically formulated friction-modifier break-in oil and brake-in oil filter was a great idea!
👎🖒💘💌💌💌💜💛💚
Good job 👌👍
thank you
I guess you have to work with what you have! Rough and ready work at it’s finest 😂
Well. Done.
Every thing looks okay but why not the new oil 🙏🏼
Похоже движок неубиваемый совсем, поэтому привезли в прачечную, а не на ремонт в мастерскую!
Good ... you are expert in doing the job , but you never tell from which country ...? Nepal , vietnam , ruhinya , philipines , thailand , muun , or indo china ...? want to know ...! im from kuala lumpur , tq for the video.
Sangat pemiliar sekali dalam menguasi mesin saat direatorasi
It is pretty evident that the “crust” on the outside is pretty uniform and homogeneous. I’d say they covered it with in a substance and then fine dirt or dust was applied and left to cake on. Not a single seized or rusted on bolt.
Its more than what you're doing sat there in your armchair doing fuckall allday and achieving nothing.
I've seen crust like that on motors in feed mills. They are exposed to fine dust over a long period of time.
The engine looked like it was sealed ok, so I would not expect the bolts to be stuck. Imho
@@johnnytoobad4287
Yes, but my beef with these videos and the rust repair videos is that it’s ALWAYS uniform and often on different materials on the same piece. Evidently a spray and pray patina.
Its just cooked on shit man... pretty common.. and thoes bearings were hammered.. Now don't mention not honing the bore or the shitty assembly techniques...
I see working engines like this all the time, it's just soaked in oil and covered in dust from it's environment. I've come to worse engines and every single bolt has come out with a hand spanner because it was all soaked in oil and diesel from being kept filthy for years.
Nice job!
При реставрации главное не только внешний вид. Ещё нужно восстановить изношенные детали.. А в ролике я вижу *создание товарного вида* как у перекупов.. Почистили, помыли, покрасили.. Собрали.. Как есть.. А в итоге ещё и отработку с песком и мусором в картер залили! Которая вкладыш как наждком спилит при работе..
Не зачёт! Лайка не будет.
All that work and he tips the dirty oil back into the motor. And looks like he ran the cleaning diesel thru a rag and reused that too.
Yep … I could had cried ..
Did a pickup truck deliver that two hundred lb engine?
No, a motorbike!
WOW...carrying a 100 kilo engine on the back of a Yamaha scooter alone is worth a thumbs up!
I think it's like 200 kilo. 120kilo is for 6kW 3000rpm single cylinder Slavia 1S90A as an example of faster and weaker engine, that is way lighter.
Nice spray booth.
Not a good idea to oil the back side of the bearing shells, it reduces clearance. The back of the bearings and where they sit should be clean and dry.
Я тоже был удивлён!
@@dokuchai แ
A suggestion! From your CZcams earnings buy yourself a torque wrench and a set of feeler gauges as well as a bottle of NEW oil. Old oil destroys engines.
Dear ctiley2212
👍👌👏 Exactly what I thought instantly too!
Best regards, luck and health.
Blon punya duit dia bang... Pan gajian abis buat beli sembako,
Привет всем токие двигателя очень востребованы
These engines will run with brick dust and hammers in the sump, new oil would've been better for sure, but sometimes the budget isn't there. As for feeler gauges, fair enough, but equally, these things were designed to be set up by a farmer in a field. Once you know how a properly adjusted tappet feels on one of these old things, it's probably about right!
@@rasyamotor1701 anjir nyasar wkwk
Great job my friend
И в конце отработки в двигатель залили)
Very good
After doing such a nice job, the sump oil should have been new oil
Gostei foi da machadinha... que já tem até o dente certo na lâmina para tirar a peça...
The background sound is so thriller 😀
Tuyệt vời
Việt Nam 1st . Chúc kênh thành công và tiến tới
cảm ơn bạn nhiều
You need to clean out that water jacket of rust and silt. your engine will run to hot and wear faster.
very perfect your work i am starting to work on these services now
Increíble restauración y me parece haber visto aceite usado????
Не пойму зачем грязи из лужи в мотор залили...
that neat it runs on soda and old oil
Wonderful.
Помыли, покрасили, сменили прокладки и заработало? Ой не верю ! Ребята, да вы даже подшипники не сменили, я уже не говорю о вкладышах и поршневой! Это дичь какая то! А заливать ОТРАБОТКУ в картер это вообще пиздец!
внимательно посмотри когда мыли там коленвал задраный, что толку от таких ремонтников.
Very nice rebuild! Ron USA
thank you
Những chiếc đầu máy quen thuộc. Mình học hỏi dc nhiều thông tin từ video 😍
Я охренел когда он на мотике это привёз)))
Тоесть тебя только это смутило? А то что он подшипники обухом забивал и мягкие вкладыши потом удлинителем ничего?
Или же масло старую грязную золил обратно.
Я охренел от работы в шлеме и маске. Тб на уровне
Этот двигатель работал еще месяц назад, потом его закинули в песок на месяц и типо перебрали, причем мех обработки как таковой и не было. Сомнительная сборка. И все это лишь для контента
@@user-su8od3qd9t trocou bronzinas de biela e as buchas do virabrequim sem ao menos brunir o eixo. 🤦♂️
Amazing 👍👍
Did you guys put the dirty oil back into a fresh engine?
My thoughts exactly, the crank rod journal didn’t look to clever, didn’t hone the bore for the new rings, the dirty oil got me,,, like washing your feet and putting your dirty socks back on …
Good to see the engine getting a second life again instead of being melted down as scrap
Good Video
Зачем вы старое масло туда залили?((
how do you put old exhausted oil in a newly rebuilt engine ... I'm speechless
same here
Having even put in a new Bigend.
But it dosen't matter even ball bearings wher put in by hammer.
Just black oil
My advice is only always change the old oil to new ! But realy good job buddy! God bless You !!
I enjoyed removing the dirt, always my favorite part, wish you brushed it after
Diese alte Öl Brühe wieder in den Motor schütten? Pour this old oil sludge back into the engine? The bearings of the balance shafts not changed? What kind of botch-up is that?
A total bodge job … bearings, used oil .. defeats the object of a engine rebuild, the big end journal didn’t look good, didn’t even hone the bore for the new rings to bed in .
@@glennfryer1539 :)))))
Nice Work 👍👍👌👌
You said in description: "I hope you find something useful from this video!"
I did. Definitely I found. Everything was new for me.
WOW so instead of oil you can use soya sauce? I have to try. LOL
Tava indo muito bem, até colocarem óleo no carter
I like the dirty....nice scrubing......👍👍👍👍👍👍👍👍👍
Thank you for the wonderful lesson
Love the background noise
Piękna praca ludzkich rąk brawo
Nalali starego oleju ?
I can't believe you put dirty oil in new engine
TAHANKIOU IRMANO
Exactamente restauración hace tiempo que veo tus videos ahora me suscrivi a tu canal por que e encanto tu trabajo Felicitaciones Saludos de Chile 💪😁🇨🇱🇨🇱
Os caras são fera na restauração.... impressionante trabalho perfeito 👏👏
Really nice work. That little engine might be very useful.
Sensacional guerreiros!!... Daqui Do Rio Grande do Norte - Brasil.
Interesting ring compressor and torque wrench.
Shame you didn’t time both parts of the lanchester balancer properly, that engine will shudder
Ráp máy gì mà không xài keo ron gì hết. Không keo thì ít nhất cũng thoa mỡ bò chứ. Làm một cái máy như vậy cũng cực công, đã làm thì làm cho an toàn tuyệt đối luôn
tất cả dều có zoăng mà bạn
Có packing, oring keo làm j nữa bác. Nhưng hình như máy này cố tình đắp bùn đất vào. Chứ ko phải để ngoài trời lâu. Vì để ngoài trời lâu như vậy ko thể tất cả các con ốc đều mở dễ dàng vậy.
Специально в песке подержали типа реставрируют
This was a fantastic video you certainly know your business. Wonderful to watch you take a horrible old piece of machinery and turn it into a piece of gold. Well done Cheers from Australia.
Какая чёткая работа , какой звук - ВЕЛИКОЛЕПНО !
На жуя ж смазал вкладыши с обратной стороны?
У меня такой же, нет з/ч его перебрать😢
@@user-ow6eu1dj1v Заказывали из Китая. Поршень, гильзу, кольца. Вкладыши и клапана с трактором в зипе были.
@@aarta2590 а как им работать без смазки? шейка задрана на колене ))
I say we pass the hat and buy these guys a torque wrench.
Excellent work👍👍👍. Thanks for sharing
Holy shit,did he seriously tip the old dirty oil back in? Guess must be wanting to change all the bearings pretty soon!
Why old oil and how you tread the bearings they are broken in 1 year
Это не восстановление или ремонт, операция называется помыть, покрасить, помазать, продать (ПППП).