Red is not a good frequency to use for this. It's why it wouldn't work at all on a window, because visible light travels through glass. You would want to use infrared frequency, which I believe is what the first ever laser microphone used; it didn't even use a real laser in fact, but rather an IR beam. UV should work as well, as long as it's high enough frequency. Higher power output and more isolated receiver would very very helpful as well of course (as you know).
Rick I love your project! ... I think what you want ideally to use is a Blue Laser. Blue wavelengths refract or change directions more. This greater variance would be helpful to your project. Glass absorbs IR. Reflectance from glass is generally only 4%. So sticking a 3mm reflective foil target dot on the glass would be best. In use, this would obscure laser light from entering the room from outside. Also, the energy from the laser is not focused, a quartz glass lens is needed or a more powerful laser.. ... A second way to greatly improve this, could be to use a reflecting telescope with a polished first surface metal reflector (not glass) Then mount the sensor diode at the tube's first surface mirror's convergence point. Reflecting telescopes are designed to look at stars, So it should work well for what you are doing. I love this project Great Job Rick and Great idea!
Okay, so I see some issues with why this didn't turn out well. Like others said, you need to protect the sensor from ambient light. I'd put it inside an opaque black tube to block out all light except what you're pointing it directly at. Another problem I see is geometry and detectability by your adversary. You need a way to ensure that you're actually positioning the sensor where the laser lands AND pointing the sensor directly toward the point that it's bouncing off from. My solution to that would significantly increase the cost of the build, but also greatly improve quality and function. use an infrared laser instead. You can then use an infrared camera without IR lights to find where the beam lands. Keep the camera attached to the sensor and calibrate it to point exactly where the sensor points. When you find where the beam lands, place the sensor and camera there, then use the camera to aim the sensor at the window. When positioned correctly, the beam should blind the camera. Many infrared cameras also have a microphone input, so you can use that to connect your sensor. Most cameras also have built in recording capability upon sensing audio or motion, so if you manage to clean up the ambient noise by shielding it, you should be able to automatically record. A Raspberry Pi and IR camera module would be rather affordable and princely serve this purpose well, but you can find deals on IR security cameras for less than the cost of that if you know where to look.
You have a lot of good ideas. I don't think I had any flourescent lights on in that room at the time, but you are correct that they do produce a 120hz hum. Regular incandescent bulbs produce a 60hz hum. The AC lines in the house can produce the same hum in the amplifier circuit itself if it's not shielded properly. I honestly have no idea what caused the sine wave in this recording. If I measured the frequency it might help narrow it down.
By reflecting the laser off of the reflective surface, you essentially modulated the amplitude of the laser beam using the music as the modulation source. When you said it sounds like an AM radio, that is because you CREATED an AM radio, which is literally amplitude modulation. The only difference is you used visible light, while a radio station uses a much lower frequency light that's invisible to us/
AFAIK a real laser mic should use FM, not AM. It is an interferometer that measures the tiny distance change by mixing the sent with the received laser wave. Similar setups are used to make holograms. You can e.g. detailedly analyze the partial vibration of musical instruments (violin body etc.) or loudspeaker diaphragms this way. An extreme application of this is the astronomic gravitation wave detector.
Do you have any experience of laser transmitted sound, I believe my neighbour may be targeting our house, 5m away with sound, you can hear it outside but it is audible in our home, I would like it blocked as it is annoying as much as sinister
thank you for this, this gives me ideas for how to frankenstein together something similar now that i understand how those laser parabolic mics can be done on the cheap. cheers, mate
i think putting a shroud around the light sensor would allow you to pick up less ambient light and more of the laser, also maybe using a more powerful laser.
Yeah, and also make a larger angle between laser and receiver beam. Because the less the angle means less the vibration deflection from the mirror, and thereby lower audio quality.
but then the rig is totally distance dependant. idealy it should work at anny distance with minimal settup required for setting up the angles and distance correctly
What if you also put a lens around the photosenor? That way you could align it with where the laser bounces off, so you can only be getting a signal from the laser.
You need to increase the SIGNAL/NOISE ratio. Notice that Your system worked perfectly in dark conditions and in proximity. Maybe using an INFRARED LASER or a powerful BLUE laser as a source will be a good idea. Also using a small array of sensors (maybe nine, and an amplifier) could help. Also putting the sensors in a small Cassegrain telescope could be a good idea (But for infrared sensors You will have to use silver-coated reflective surfaces and maybe cooling with solid CO2)
Really nice video, it's possible that window glass inertia is too high for the cell speaker and does not really vibrate. You could also try to put the photosensor inside a cilinder to filter the photo-noise
longer wavelength lasers work much better; less distortion. Which is not to say laser mics work well at all. Any fog, precipitation or dust in the air and all you hear is white noise. Same deal if there is water running in the room.
Very cool to see this implemented with such a cheap setup. As many others had said, there is room for improvement, even maintaining it cheap, like isolating the receiver from external lights Anyway, it was a nice video!
if we see the sound waves through video camera and convert that into digital music data file through app.our camera is our microphone or waves digital converter.
A stronger laser output, a more sensitive light detector, or maybe a signal amplifier between the Photo-transistor and the amplifier to act as a pre-amp may help. light is pretty sensitive to any interference. A solid mount with a very heavy base would certainly improve the project. The idea being to keep the light source as still as possible. I have also seen success with a cell from a solar panel used in place of the photo-transistor.
Try shielding your receiver sensor with a cardboard tube. Your received signal may be polluted by noise from outside light. Try also a small solar cell and shield it too, or try doing it when it's dark.
Use ir sensor from old tv, vcr , etc mount it to the eyepiece of a telescope mount the ir laser to the telescope sighting scope after calibrating and sightimg in the laser to the scope you will have a very accurate device using a tint piece of reflector tape like a small dot a hole punch makes and sticking it to the center of the glass of a window you could get a clear signal from maby 5 miles away especially at night. If you modulate the lasar giving it a carrier fq. That could then be detected as in an am radio receiver or cristal radio to extract the modulated audio. This would also help to eliminate external noise and to mak it even better you could use supressed carrer demodulation ar a deferential am/fm demodulating method to have a way of tweeking or cleaning up weak signals from long distances or double pained windows or even to listen through walls.
Place the photodiode inside black pvc pipe , to protect the sensor from ambient light like others have said. Also try using magnifying lens Double pane glass is hard to pick up sound from ! any good spy would Know this would give up your location . spy would repeater the signal and send the signal to 2nd location
Years ago I learned about our alphabet agencies using this technology in Russia. I believe you need to use a prism as a light collector or concentrator? I actually stuck to the window to get better sound? I cannot remember the exact specifications
That sine wave I heard in the long distance test has me very curious, did you have fluorescent lighting in that room? I know that fluorescent lights operate at very high frequencies, so maybe we're listening to your lights? I'll bet that a narrow bandpass filter (passing the laser's color) would be really helpful. I was also thinking that maybe measuring the mirror deflection might be a good step towards optimizing the hack, perhaps a very small aperture in front of the photodiode could help?
take a big coffee can, empty the contents, cut out the top and bottom, create a diaphragm out of cellophane with a mirror in the middle. Then point the can at a location you want to listen to. Use the same technique you did here except against the mirror on the diaphragm
Plus a fairly high power infrared laser unless you want it to be seen. aside from that a lot of cell phones and security cameras can already see infrared so you might be seeing lol
Last example failed (and will always fail) because the laser pass through the clear glass window (majority of light waves are only refracted, only few are reflected). You can tape a mirror piece on the window to make it work. The story about this gadget has to do with placing a very small prism in the window which refracted the light waves in 180 degree (if you know the story)
Any vibration on the glass would have been very effectively dampened by the phones mass. If instead placed it so it would not have been in contact then it might would have worked.
Try separate the laser into 2 using semi mirror, bounce the split one into the target mirror, then combine it to laser split 2. It will create interference. Then use high fps camera to see the interference changing. Translate it to audio signal. It might work like LIGO (gravitational wave detector). See like this demo: czcams.com/video/ajZojAwfEbs/video.html
Your story does not match the preamble. It proposes that one can hear what's happening in a room across the street due to reflexion of laser beam from the window glass. And no actual solution is given. And even more. This method will not work due to these facts: - rfelected beam is not bright at all(see Nitin Kumar's comment) - reflected beam must change it's direction(due to rotational vibration of the lighted area of glass) or your gage will give constant signal. - reflected beam must not travel much or it will hit the transistor only ocasionally to give you some random spikes of signal - even if reflected beam travel is just as long as to cover partially sensitive area of the transistor(it is tiny) with the reflected beam(and does move) at all times and you do hear the spies, they will not be sharing any secrets but wondering, why do they have a laser beam in their room :)
This is a very low budget proof of concept. It's not designed to be used by real spies. While it isn't very high tech, you CAN actually use it to pic up sound vibrations and listen. It's just a fun project meant to show what can be done on a low budget and limited time.
That's a known Soviet spy technology of the 1980's, used to spy the American embassy in Moscow. It was defeated using walkmans with loud rock music attached to the windows. Also double glass windows could defeat the laser.
you need more bass like a regular tv speaker or yourself speaking on the other side of the glass, that tiny speaker barely moves the air molecules that move the glass
no it will not help. Two problems here - laser is not reflected from windows as good as from CD (which is especialy made to reflect it), second light sensor is not that good - it just can getect small changes from small vibrations of window.
you need a little bit more equipment so maybe a little bit more advanced and more directive a laser that is brighter and not good with toys I know you only want to make it for $20 but try going a little bit higher with a little bit specific aided equipment and I think you would have a excellent covert pickup
The laser has to point directly back at you to get the feedback, this is why the Americans were putting little prisms on the corner of the window...So I haven't watched yet but I don't think it will work..
DarkMaMon It's not a solar cell, it's a diode that detects light levels. The vibrations on the mirror effect the laser light that reaches the diode in the same way that the sound waves travelling through the air would effect the microphone. Because you are not trying to detect sound waves but instead trying to detect vibrations in a solid object the reflected, light from the laser acts as the medium in which the signal is transmitted. It has to be a laser that gives the light of the way they produce the light. A normal focused beam of light from a lamp or LED would dissipate too quickly through the air and be lost where as the laser can be detected over longer distances with minimal power requirements.
No, you can attach a small prism on the window to reflect the light without it getting through the glass: www.precisionoptical.com/img/products/porro-prism2.jpg
The idea is to set it up using a laser visible to the human eye and then when you actually go and use it switch to an infrared. set up has to be perfect though any variation in angle (45degrees is used) will throw you off.
I really need someones help to prove to police I'm not hearing things. Me and my family are being psychologically tortured and because the tech being used is microscopic and unknown to police, they've put it down to mental health and now I'm stuck in situation with my mum and sister both showing suicidal tendencies but unaware its because of 4-6yrs of psychological torture and abuse to see the physical and psychological impact and how dif a person could be made fo look (my sisters been diagnosed with EDS within this time) and since looking into this iv noticed how the national and global statistics actually reflect the proof of this technology being around for at least 8yrs with its main causes being mistook for Menopause, BPD EDS, Schizophrenia and also in the deaths statistics for deaths by heart attack (mostly caused in sleep) and the overdose deaths caused by opiates as the 1st thing it causes is Adrenal Fatigue Syndrome which shares the exact same signs, symptoms and side effects of heroin withdrawal and at same time if addicted fo crack cocaine too then overuse of caffeine and other stimulants symptom worsens crack use and also drug dealers have been targeted with this tech to experiment on drug addicts that have enough trauma to be traumatized repeatedly and tortured into desperation once done with as this is how the tech is being destroyed and none to very little evidence left as this tech is heat seeking and attracted fo dark things n spaces so ashtrays, lighters and other drug paraphernalia is understandably collecting most of it if not all then burning throwing or losing. Leaving the person tortured to such a low state that also stand little to no chance of ever being caught or investigated given the stereotype of crack and heroin addicts and the stigma of mental health and police also making it easy to set the person up to sound and look like every single red flag of an undiagnosed mental health condition so this advanced technology can go undetected and disguised as mental health or hormone related due to adrenal fatigue. This is my problem iv been ser up over past 4-6yrs n last 2 of which iv been tricked and traumatized into a state of constant fight or flight and believing the threats being made and dangers I was being warned of by voices I could hear and who turned out to be several people from my past and an old neighbour who set up several of the people involved in setting me up so that in future now 13yrs later they've been set up to be the 1s held responsible so that they almost definitely join in setting me up for heart attack that will kill me before I get taken seriously by anyone or police. Iv uploaded some videos with microscopic view of the technology I found on my black pen and on skin and audio recs of what I'm hearing 247 just about audible and subliminal psychological trauma experiments then tailoring the torture specific to my weaknesses etc.
So basically you did is waste your time, waste our time, waste space on hard drive, burn some money, proven it works which we already know, not learned anything new, not showed us anything new. My question is why ?
Togenhere sila😂
axaxaxax😂
sizam shuyodan keldizmi😂
@@user-rg3el8xd9v da
😂😂
😂😂😂😂
Togenherni silkasidan keganla bomi
Red is not a good frequency to use for this. It's why it wouldn't work at all on a window, because visible light travels through glass.
You would want to use infrared frequency, which I believe is what the first ever laser microphone used; it didn't even use a real laser in fact, but rather an IR beam.
UV should work as well, as long as it's high enough frequency.
Higher power output and more isolated receiver would very very helpful as well of course (as you know).
Rick I love your project! ... I think what you want ideally to use is a Blue Laser. Blue wavelengths refract or change directions more. This greater variance would be helpful to your project. Glass absorbs IR. Reflectance from glass is generally only 4%. So sticking a 3mm reflective foil target dot on the glass would be best. In use, this would obscure laser light from entering the room from outside. Also, the energy from the laser is not focused, a quartz glass lens is needed or a more powerful laser.. ... A second way to greatly improve this, could be to use a reflecting telescope with a polished first surface metal reflector (not glass) Then mount the sensor diode at the tube's first surface mirror's convergence point. Reflecting telescopes are designed to look at stars, So it should work well for what you are doing. I love this project Great Job Rick and Great idea!
Okay, so I see some issues with why this didn't turn out well. Like others said, you need to protect the sensor from ambient light. I'd put it inside an opaque black tube to block out all light except what you're pointing it directly at. Another problem I see is geometry and detectability by your adversary. You need a way to ensure that you're actually positioning the sensor where the laser lands AND pointing the sensor directly toward the point that it's bouncing off from. My solution to that would significantly increase the cost of the build, but also greatly improve quality and function. use an infrared laser instead. You can then use an infrared camera without IR lights to find where the beam lands. Keep the camera attached to the sensor and calibrate it to point exactly where the sensor points. When you find where the beam lands, place the sensor and camera there, then use the camera to aim the sensor at the window. When positioned correctly, the beam should blind the camera. Many infrared cameras also have a microphone input, so you can use that to connect your sensor. Most cameras also have built in recording capability upon sensing audio or motion, so if you manage to clean up the ambient noise by shielding it, you should be able to automatically record. A Raspberry Pi and IR camera module would be rather affordable and princely serve this purpose well, but you can find deals on IR security cameras for less than the cost of that if you know where to look.
😮
You have a lot of good ideas. I don't think I had any flourescent lights on in that room at the time, but you are correct that they do produce a 120hz hum. Regular incandescent bulbs produce a 60hz hum. The AC lines in the house can produce the same hum in the amplifier circuit itself if it's not shielded properly. I honestly have no idea what caused the sine wave in this recording. If I measured the frequency it might help narrow it down.
By reflecting the laser off of the reflective surface, you essentially modulated the amplitude of the laser beam using the music as the modulation source. When you said it sounds like an AM radio, that is because you CREATED an AM radio, which is literally amplitude modulation. The only difference is you used visible light, while a radio station uses a much lower frequency light that's invisible to us/
I don't understand how the amplitude of the light would change.
AFAIK a real laser mic should use FM, not AM. It is an interferometer that measures the tiny distance change by mixing the sent with the received laser wave. Similar setups are used to make holograms. You can e.g. detailedly analyze the partial vibration of musical instruments (violin body etc.) or loudspeaker diaphragms this way. An extreme application of this is the astronomic gravitation wave detector.
@@AerialTheShamen
You stole my thunder.
This is the correct information.
Thank you for your kind comments! I'll try to come up with some more spy gadget projects to feature on my channel. If you have any ideas, let me know!
thanks!
Let me know what it is that you hope to invent ?
I'm Steve at Niagara Falls Ontario.
Geologist
Do you have any experience of laser transmitted sound, I believe my neighbour may be targeting our house, 5m away with sound, you can hear it outside but it is audible in our home, I would like it blocked as it is annoying as much as sinister
Use an IR laser it will reflect off of the glass. However, you won't be able to see it
thank you for this, this gives me ideas for how to frankenstein together something similar now that i understand how those laser parabolic mics can be done on the cheap. cheers, mate
i think putting a shroud around the light sensor would allow you to pick up less ambient light and more of the laser, also maybe using a more powerful laser.
I think these are both great ideas!
Yeah, and also make a larger angle between laser and receiver beam. Because the less the angle means less the vibration deflection from the mirror, and thereby lower audio quality.
but then the rig is totally distance dependant. idealy it should work at anny distance with minimal settup required for setting up the angles and distance correctly
What if you also put a lens around the photosenor? That way you could align it with where the laser bounces off, so you can only be getting a signal from the laser.
You need to increase the SIGNAL/NOISE ratio. Notice that Your system worked perfectly in dark conditions and in proximity. Maybe using an INFRARED LASER or a powerful BLUE laser as a source will be a good idea. Also using a small array of sensors (maybe nine, and an amplifier) could help. Also putting the sensors in a small Cassegrain telescope could be a good idea (But for infrared sensors You will have to use silver-coated reflective surfaces and maybe cooling with solid CO2)
Really nice video, it's possible that window glass inertia is too high for the cell speaker and does not really vibrate. You could also try to put the photosensor inside a cilinder to filter the photo-noise
longer wavelength lasers work much better; less distortion. Which is not to say laser mics work well at all. Any fog, precipitation or dust in the air and all you hear is white noise. Same deal if there is water running in the room.
You tried it and you got some results, power to ya! The commercial ones cost upward of £30k.
Very cool to see this implemented with such a cheap setup. As many others had said, there is room for improvement, even maintaining it cheap, like isolating the receiver from external lights
Anyway, it was a nice video!
Wow! That sounds a lot better than I was expecting!
if we see the sound waves through video camera and convert that into digital music data file through app.our camera is our microphone or waves digital converter.
A stronger laser output, a more sensitive light detector, or maybe a signal amplifier between the Photo-transistor and the amplifier to act as a pre-amp may help. light is pretty sensitive to any interference. A solid mount with a very heavy base would certainly improve the project. The idea being to keep the light source as still as possible.
I have also seen success with a cell from a solar panel used in place of the photo-transistor.
You should do a Collab with Styro Pyro. Two mad scientists together on one video, what more could one ask for
Try shielding your receiver sensor with a cardboard tube. Your received signal may be polluted by noise from outside light. Try also a small solar cell and shield it too, or try doing it when it's dark.
Togen here❤❤
Use ir sensor from old tv, vcr , etc mount it to the eyepiece of a telescope mount the ir laser to the telescope sighting scope after calibrating and sightimg in the laser to the scope you will have a very accurate device using a tint piece of reflector tape like a small dot a hole punch makes and sticking it to the center of the glass of a window you could get a clear signal from maby 5 miles away especially at night. If you modulate the lasar giving it a carrier fq. That could then be detected as in an am radio receiver or cristal radio to extract the modulated audio. This would also help to eliminate external noise and to mak it even better you could use supressed carrer demodulation ar a deferential am/fm demodulating method to have a way of tweeking or cleaning up weak signals from long distances or double pained windows or even to listen through walls.
Never seen this kind of project before . Nice job , keep it up . Do more video on spy gadget !
To spy on someone from the dividing wall of my semi-detached house with a laser and a photoresist, amplifier and speaker. It works in my opinion.
try a solar cell instead of the ambient light sensor. pull one from a broken solar garden light.
Place the photodiode inside black pvc pipe , to protect the sensor from ambient light like others have said. Also try using magnifying lens Double pane glass is hard to pick up sound from ! any good spy would Know this would give up your location . spy would repeater the signal and send the signal to 2nd location
Years ago I learned about our alphabet agencies using this technology in Russia. I believe you need to use a prism as a light collector or concentrator? I actually stuck to the window to get better sound? I cannot remember the exact specifications
Togenhere😂
That sine wave I heard in the long distance test has me very curious, did you have fluorescent lighting in that room? I know that fluorescent lights operate at very high frequencies, so maybe we're listening to your lights?
I'll bet that a narrow bandpass filter (passing the laser's color) would be really helpful.
I was also thinking that maybe measuring the mirror deflection might be a good step towards optimizing the hack, perhaps a very small aperture in front of the photodiode could help?
take a big coffee can, empty the contents, cut out the top and bottom, create a diaphragm out of cellophane with a mirror in the middle. Then point the can at a location you want to listen to. Use the same technique you did here except against the mirror on the diaphragm
What I can't get over: a circuit board designed to receive and transmit sound is fine accepting light input and still knows to transform it to sound?
Would be cool to see an upgraded version for sure
Perhaps a capacitor in series with the photo-diode (receiver) and the pre-amp would filter out the background noise.
You got to use like a telescope or binoculars for the sensor I remember seeing the plans for similar a long time ago
Plus a fairly high power infrared laser unless you want it to be seen. aside from that a lot of cell phones and security cameras can already see infrared so you might be seeing lol
Hech narsa olmasdan yasashni hohlaganlar nechtamz😅
Last example failed (and will always fail) because the laser pass through the clear glass window (majority of light waves are only refracted, only few are reflected). You can tape a mirror piece on the window to make it work.
The story about this gadget has to do with placing a very small prism in the window which refracted the light waves in 180 degree (if you know the story)
or you could tape the phone on a mirror
Nimagap
How much will is cost to build one for customized
one laser of infrared reveleable only visor( ir) or cell camera you earl in very security of distance.😉
Togen silaaa😂
RICKOS is there an item that can b e purchased to stop /interefere with covert listening devices within walls?
Use a solar panel to receive the reflected beam
Togenhere is here 😂
Any vibration on the glass would have been very effectively dampened by the phones mass. If instead placed it so it would not have been in contact then it might would have worked.
Have you got rid of the glass ...
& Any effective improvement??
Dood, how did you know how to do that? Your awesome.
Try separate the laser into 2 using semi mirror, bounce the split one into the target mirror, then combine it to laser split 2. It will create interference. Then use high fps camera to see the interference changing. Translate it to audio signal. It might work like LIGO (gravitational wave detector).
See like this demo: czcams.com/video/ajZojAwfEbs/video.html
very nice...you should work for the cia, fbi,or mi6 :)
Togenhere
Togenhere dan keganla -------------->❤
Togenhere dan krganla bomi😂
Your story does not match the preamble.
It proposes that one can hear what's happening in a room across the street due to reflexion of laser beam from the window glass. And no actual solution is given.
And even more. This method will not work due to these facts:
- rfelected beam is not bright at all(see Nitin Kumar's comment)
- reflected beam must change it's direction(due to rotational vibration of the lighted area of glass) or your gage will give constant signal.
- reflected beam must not travel much or it will hit the transistor only ocasionally to give you some random spikes of signal
- even if reflected beam travel is just as long as to cover partially sensitive area of the transistor(it is tiny) with the reflected beam(and does move) at all times and you do hear the spies, they will not be sharing any secrets but wondering, why do they have a laser beam in their room :)
This is a very low budget proof of concept. It's not designed to be used by real spies. While it isn't very high tech, you CAN actually use it to pic up sound vibrations and listen. It's just a fun project meant to show what can be done on a low budget and limited time.
That's what i'm saying.
It is a fun project wich can not be used for the purpose, described in the preamble. That's the only thing i didn't like :)
That's a known Soviet spy technology of the 1980's, used to spy the American embassy in Moscow. It was defeated using walkmans with loud rock music attached to the windows. Also double glass windows could defeat the laser.
can It work if your across the street ,and point it at a group not behind a window?
Pretty damn impressive
oh wow, cool hack. I think filtering white noise in Audacity would make it more clear. Maybe I will expt something similar. Peace! :D
you need more bass like a regular tv speaker or yourself speaking on the other side of the glass, that tiny speaker barely moves the air molecules that move the glass
Thanks for the tip. I'll have to try it again with something that has a little more umph.
no it will not help. Two problems here - laser is not reflected from windows as good as from CD (which is especialy made to reflect it), second light sensor is not that good - it just can getect small changes from small vibrations of window.
TCreatorO
Instagramdan keganlar like
Togenhere🖐🏼
you need a little bit more equipment so maybe a little bit more advanced and more directive a laser that is brighter and not good with toys I know you only want to make it for $20 but try going a little bit higher with a little bit specific aided equipment and I think you would have a excellent covert pickup
Does it matter which color laser you use
very interesting !
Yes! I saw something like this in Treadstone a few days ago👀.
I thought it was BS 🤔
5:54 use reflektor tape to window
What kind of photo cell are you using
The laser has to point directly back at you to get the feedback, this is why the Americans were putting little prisms on the corner of the window...So I haven't watched yet but I don't think it will work..
Yeah , no worries .. Try checkout video on kipkay channel .. Kind of cool too !
Please I will like to get in touch with you concerning this product.
Excelente
How does that work? How that solar cell turn the light into frequency?
DarkMaMon It's not a solar cell, it's a diode that detects light levels. The vibrations on the mirror effect the laser light that reaches the diode in the same way that the sound waves travelling through the air would effect the microphone. Because you are not trying to detect sound waves but instead trying to detect vibrations in a solid object the reflected, light from the laser acts as the medium in which the signal is transmitted. It has to be a laser that gives the light of the way they produce the light. A normal focused beam of light from a lamp or LED would dissipate too quickly through the air and be lost where as the laser can be detected over longer distances with minimal power requirements.
So? If I were to try and spy on someones conversation, they would have to have a mirror on them?
No, you can attach a small prism on the window to reflect the light without it getting through the glass: www.precisionoptical.com/img/products/porro-prism2.jpg
Richard Noggin
No, you reflect the laser off their window.
The idea is to set it up using a laser visible to the human eye and then when you actually go and use it switch to an infrared. set up has to be perfect though any variation in angle (45degrees is used) will throw you off.
What stops this if you're the target
. ТС в 13ч огонь 🔥
I really need someones help to prove to police I'm not hearing things. Me and my family are being psychologically tortured and because the tech being used is microscopic and unknown to police, they've put it down to mental health and now I'm stuck in situation with my mum and sister both showing suicidal tendencies but unaware its because of 4-6yrs of psychological torture and abuse to see the physical and psychological impact and how dif a person could be made fo look (my sisters been diagnosed with EDS within this time) and since looking into this iv noticed how the national and global statistics actually reflect the proof of this technology being around for at least 8yrs with its main causes being mistook for Menopause, BPD EDS, Schizophrenia and also in the deaths statistics for deaths by heart attack (mostly caused in sleep) and the overdose deaths caused by opiates as the 1st thing it causes is Adrenal Fatigue Syndrome which shares the exact same signs, symptoms and side effects of heroin withdrawal and at same time if addicted fo crack cocaine too then overuse of caffeine and other stimulants symptom worsens crack use and also drug dealers have been targeted with this tech to experiment on drug addicts that have enough trauma to be traumatized repeatedly and tortured into desperation once done with as this is how the tech is being destroyed and none to very little evidence left as this tech is heat seeking and attracted fo dark things n spaces so ashtrays, lighters and other drug paraphernalia is understandably collecting most of it if not all then burning throwing or losing. Leaving the person tortured to such a low state that also stand little to no chance of ever being caught or investigated given the stereotype of crack and heroin addicts and the stigma of mental health and police also making it easy to set the person up to sound and look like every single red flag of an undiagnosed mental health condition so this advanced technology can go undetected and disguised as mental health or hormone related due to adrenal fatigue. This is my problem iv been ser up over past 4-6yrs n last 2 of which iv been tricked and traumatized into a state of constant fight or flight and believing the threats being made and dangers I was being warned of by voices I could hear and who turned out to be several people from my past and an old neighbour who set up several of the people involved in setting me up so that in future now 13yrs later they've been set up to be the 1s held responsible so that they almost definitely join in setting me up for heart attack that will kill me before I get taken seriously by anyone or police. Iv uploaded some videos with microscopic view of the technology I found on my black pen and on skin and audio recs of what I'm hearing 247 just about audible and subliminal psychological trauma experiments then tailoring the torture specific to my weaknesses etc.
Amazing
what is the name of the software used to get audio in pc or laptop ?
Audacity
He literally says it in the video...
Why use a red laser? A person can see it. Use inferred lasers
You can use the Audacity to remove the noise also.
The man
I worked in the government when this was highly classified!
Togenhere dan korib keganlar bormi
read radar books, full of ideas to interpret bad signal
nice :)
This is awesome until someone does it to you....ugh
Bro some people use this device and hear my talks. How to stop or how to disable this device
Can you make me one of these. I will pay
Nsa cia fbi eat your hearts out.
Man! Clean that tip or get a new one! Looks like you been using it to melt plastic :)
#freepress #espionnite 🍥🍥🍥🍥
Yeah. Trash
Boooooo booooooooo
Too much talking.....
fake video
Are you a crook?
So basically you did is waste your time, waste our time, waste space on hard drive, burn some money, proven it works which we already know, not learned anything new, not showed us anything new. My question is why ?
Go do it better yourself then. I'll wait here.
@@RickOsgood I can not, that is why I did not even try. For me it is better to not do what I can not do right.
Togenhere sila 🎉
Togenhere