VQ Gallery Gaskets | infiniti G35, G37, 350z, 370z

VQ Gallery Gaskets | infiniti G35, G37, 350z, 370z
Hope you enjoyed the video don't forget to leave a LIKE and SUBSCRIBE also hit the BELL so you get a notification when new videos ARE POSTED!!!
Follow me on instagram:
Mechanic Page: bit.ly/2Dl9vl7
Car Page: bit.ly/35D6JJxr

[@darkspartan806]

Thanks for the video bro. Dealer quoted me $2400 for a new water pump on my G35X. Will do it myself & replace everything including the gally gaskets down to the timing chain. Total cost in parts, $700.

[@Runescape.]

the socket you bought was one made for the crank pulley bolt. but you can make it yourself at home with some duct tape and a long socket, just tape a few sockets onto each other to add more rotational mass, that is literally all its doing is that its bigger and heavier, like a heavyweight boxer throwing a punch, the heavier you can make the socket the more rotational mass it has to loosen that bolt up, because impact guns work on the principle of a hammer, the heavier your hammer is the more damage is can do when you swing it. also you should buy a 2nd car get a honda because these nissans are not reliable for a daily driver. they are more weekend cars for good weather, that is all i would own one for.

[@jarvond21]

Hell yeah 😁 good watch!! I learned a thing 😃. I'm pulling my buddies motor on his G37 after work today and I know how to do the motor mounts now

[@nikodimosmarkose6962]

You could’ve used a breaker bar for the crank bolt bro.

[@noirelol]

did you have to recharge the ac after disconnecting the lines or did the ac work again after reconnecting them

[@flipmode00]

Great video. tks again for posting them

[@tylerdisappeared]

how much you spend on parts in total bro

[@scatpack1381]

Thanks for the tips. How much labor would that be?

[@alex7x8]

Thanks for the tick socket advice - 2 seconds and crankshaft pulley bolt is done.

[@gloglo1275]

I’m at 15 psi at idle and 35ish at 2k. I also have a p0021. I guess is that wonderful gallery gasket.
What parts did you buy? I know the gallery gaskets, but did you buy another chain, tensioner, chain guides?

[@MinimalW204]

did it clear the codes ?

[@deepfrieddeals]

Impressive.

[@panchogomez4238]

When you take off your crank should you worry about it spinning and it messing with the timing

[@JulesMechanics]

No

[@rightanxlog4196]

Can you make a video on how to replace a g35 hood

[@herbie400]

What is the name and size of the socket you use ???

[@panchogomez4238]

Did you find the same of the socket?

[@redroseproductions4479]

How did you empty the ac system?

[@OhToeKnee]

how long was this process? i need to replace my gallery gaskets XD

[@JulesMechanics]

3 days

[@ez-duz-it9683]

Smh I really needed to know how to put the chains back on

[@brandenbryant4687]

Need a big ass cheater bar and go from the back side to the flywheel bolts to keep the crank from turning 🤦🏻‍♂️

[@kevovq3727]

Does solid mounts cause a lot of vibration in car???

[@JulesMechanics]

Yup

[@yrrrrrrrrrrrrrrrrrrrrrrrrrrrrr]

how many miles you had?

[@JulesMechanics]

120k

[@yrrrrrrrrrrrrrrrrrrrrrrrrrrrrr]

@@JulesMechanics im at 125k i guess its time.

[@gmm1904]

Thanks for sharing. My 08 g35 has 117,000. How many miles should galley gasket be replaced?

[@panchogomez4238]

I’m at 115,000 for my g37 2013 , I need to do the water pump and I might as well should do the thermostat and gallery gaskets while I’m at it.