4 "Must-Haves": Don't Start Working on the Bench Grinder until you've done These Things
Vložit
- čas přidán 2. 07. 2024
- Let's speak about 4 'must have' things You Must Do Before You Start Working on a bench grinder
Bonus: Easy to make DIY Grinding wheel balancing fixture
📐 Download Free plans - mazaydiy.com/grinding-wheel-b...
👁🗨 3D CAD model - grabcad.com/library/homemade-...
▶️ How to install bench grinder and removing vibrations, balancing, faceplate and and so on:
00:00 Cheap bench grinder "from the box"
00:25 Balancing Grinding Wheels
03:01 Minimizing end-face runout
04:00 Truing grinding wheels
04:22 Secure a bench grinder
🔨 To make it I used:
Plywood Bench Vise - • How To Make A Bench Vi...
Sharpening stand - • 3 DIY Tool Sharpening ...
Drill Press Machine - • DIY Drill Press Machin...
➡️ Follow me - / mazaydiy
☕ Buy me a coffee - www.buymeacoffee.com/mazaydiy - Jak na to + styl
DIY Grinding Wheel balancer free plans - mazaydiy.com/grinding-wheel-balancer/
3D CAD model - grabcad.com/library/homemade-grinding-wheel-balancer-1
It's free, but you can thank me:
☕ Buy me a coffee - www.buymeacoffee.com/mazaydiy
ждём видео с разлётом круга по мастерской)
Great stuff! And yes, the diamond dresser is the #1 tool to buy. I'd say even before ANY grinder! Nowadays even angle grinder discs are so off and unbalanced it hurts the hand. Don't count on them getting true "after you use them a bit".
Jon asked about the safety of drilling the wheel, and whether it might be a risk. I’ve seen 2 alternate ways to handle that. The easier was to use a disk grinder with a masonry wheel on it, making shallow but wider cuts on the heavy side of the wheel. The more elegant way was a shop made washer to replace the stamped steel one, made with about 24 1/4” shallow holes around the inside face. You place small lead plugs into those holes to effect the balancing.
None of this to take away from Mazay’s elegant solution to creating the balancing jig from scrap, and finding side to side runout with a pencil. Nicely done, Mazay!
Thanks for the advice!
I received several opinions that my balancing method is not safe, I answered them in detail here - www.homemadetools.net/forum/diy-grinding-wheel-balancing-jig-96887#post224138
Summary - it is better (safer) to use a different method of balancing by adding additional weights, rather than drilling, although this does not apply to the design of the balancing jig.
Smart ideas. Thank you for showing.
Great work as always 😄😄
Grande!!!👍
Good video
Ну диски типа подсотрутся, и опять что ли их балансировать??
Лайк не глядя 👍
А круг не лопнет потом по калибровочным отверстиям?
Конечно лопнет😁😁😁
Да это слабое место, может при большом давлении на рабочую область и разлетется
@@liih "большое давление" - это лом с размахом.
@@MrChertel или деталь, которую затянет под предметный столик, и создаст обратный удар
Чёткая работа 👍👍👍
Благодарствую. Всё ясно, всё понятно.
Теперь подшипники тоже радуются.
Диски на болгарку не балансируешь?А если серьезно, то я бы колхозил с прижимной гайкой, наверно можно вместо штатной поставить диаметром побольше, отметить положение когда она закручена до упора. И уже на ней, делать балансировочные отверстия.
Тот случай когда с чистой совестью можно написать жалобу с мотивировкой " опасные действия" 🤦🤦🤦
👍👍👍👍
Красотень
Адекватная настройка
Идиотизм !
Техника безопасности писана кровью.
Дети ! Никогда не повторяйте за дядей !
Дядя либо самоубийца, либо провокатор-извращенец.
Да никто и никогда этим не заморачиваться! Это видео для лайка, не более. Когда коту делать нечего....
.
Как раз таки все нормальные люди заморачиваются что бы точило было идеально отбалансировано
Я думаю почему он у меня скачет по столу 😂
Жуть😱