Video není dostupné.
Omlouváme se.
How to Remove a 2015-2022 Dodge Charger Front Bumper Using 3 Tools You Already Have | ReveMoto
Vložit
- čas přidán 13. 08. 2024
- There are a lot of hard-reaching bolts on this bumper. We'll show you how to properly remove the Dodge Charger front bumper!
Where to purchase: bit.ly/15-21_C...
Website: www.revemoto.com
0:00 Start
0:29 Intro
0:54 Lower bumper bolts
1:48 Separate the fender & bumper
5:17 Remove the radiator cover
6:56 Remove the uppermost fender bolt
7:22 Air dam separation
10:58 Sidelight reflector removal
11:38 Recap
13:09 Bumper removal
13:47 Outro
Thank you for watching our Dodge Charger front bumper cover removal video. This was our first time removing the plastic bumper cover for a brand new Dodge Charger. It wasn't the easiest bumper we've done but it was a great experience. We specialize in pre-painted auto body parts and we paint a lot of these Charger bumpers. This particular Charger was our shipper's car and we were just replacing his fender for him. Yes, you have to take off the bumper to replace the fender but that is another video. Please like and subscribe if this video helped you out, it really helps our channel.
TOOLS NEEDED:
You will need a screwdriver, a socket wrench, or an impact gun with 10mm and 7mm sockets. You will also need a panel clip removal tool but you can also use a flat-head screwdriver instead.
PROCESS:
This bumper removal starts off easy enough. Like every other replacement video we do, we like to start on the bottom of the bumper and remove any bolts or clips, if any. It's pretty easy and straightforward to do. Then we move onto the wheel wells and separate the fender liner from the bumper. This is also very easy, as it only has a couple of clips holding the liner in. Every bumper will typically have a bolt securing the fender to the bumper. This marvelous Charger has three. Yup, three bolts holding the fender and bumper together, and they aren't the easiest to get to. You'll have to take off more clips on the fender liner to allow for spacing. You could also remove the tire and fender liner altogether to make it a lot easier but we felt like that was too much work. So, we just put our hand far back into the fender and removed the two annoying bolts with just the socket and no wrench. They were surprisingly loose bolts and once we removed them we realized that there was one closer to the headlights and top bumper after we took off the radiator cover. So, remove the cover held on by clips, and take off the 3rd bolt. You will also have to separate the air dam from the fender liner as well, it's secured by 3 screws. Some of you may have foglights and may not need to do this step. Lastly, unplug the side marker lights on the bumper and you can fully remove the bumper after all your hard work.
Follow Us on
FB: / revemoto
IG: / revemoto
Twitter: re...
________________________________________________________
#dodgecharger #charger #paintedautoparts #dodge #highquality #DIY #HowTo #revemoto #paintedbumper #paintedonlineparts
DISCLAIMER: While ReveMoto tries to make the information in this video as accurate as possible, we make no claims, promises, or guarantees about the accuracy, completeness, or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself (DIY) projects entail some risk. It is the sole responsibility of the viewer to assume this risk. ReveMoto is not responsible or liable for any loss, damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.
Thank you for watching!
Purchase your new bumper here: bit.ly/15-21_Charger_Bumper
Wow somebody actually step by step removed all the bolts so I know what points to hit. May you be praised bro
We're glad we can help and thank you for watching!
Thanks for this finally a detailed video on this 🙌🏿🙌🏿🙌🏿
Made it simple and easy to understand. Thanks
You're welcome! If you need a replacement Charger bumper painted to match, get it at revemoto.com
Your video really helped I wasn't trying to take the tires off. I did have to put the front on jack stands to have the tires turn a little more. Also if anyone is unlucky like me and those 2 bolts are tight, you can use a hex key as a handle being that there's not much room
Appreciate it! Glad the video helped. Hex key is smart - thanks for the tip!
Thanks for the video. Have to repair the horns.
You bet, we're glad we could be of help. Thank you for watching!
Hey so if I need to replace the top part the radiator support cover (the piece you took the 12 push pins out of) would I need to take the bumper off to replace it? Or could I replace it with it on the car?
That piece is attached to the bumper and it would be a lot easier to remove the bumper cover. You would have more visibility and range of motion. You could probably manage by removing half the bumper, but it would be difficult to reach in and see what you need to do. Thanks for watching!
Thank you so much for these videos bro
You are very 🙏. If you have any questions let me know. If you need parts for your car go to www.ReveMoto.com
If I wanted to replace a headlight ballast, I would need to follow these steps to remove the bumper correct? I don't think I can access the ballast otherwise?
Yes follow the steps to taking off the bumper and getting to the headlight would be much easier. Go to www.ReveMoto.com for all your car parts needs.
Very Appreciated for the Video, Thank You!
Glad it was helpful!
I use side cuts to get the plastic rivets off - better than the screwdriver, not as good as the tool you have.
If it works, it works! We've done the same thing in the past. Thank you for watching!
My brother, you did a great job. I need to actually pull the whole headlight assembly out because mine has water inside and I want to replace it with a new one. Does it look like the headlight comes out easy?
Yeah it does once the bumper is off
Jus removed mine! Awaiting my new bumper to come in. Thank you!
Did you buy it at www.ReveMoto.com?
@@ReveMoto I didn’t place an order yet! Short on funds right now but hopefully soon I can order one!
@@tyk248 Looking forward to it!
@@ReveMoto do you guys ship to Hawaii??
@@tyk248 We sure do!
Thank you 🙏🏻
Glad it helped! If you decide you want to replace the bumper with a painted Charger bumper, check us out bit.ly/15-21_Charger_Bumper
Thank you!
You're welcome! Please subscribe, it helps us make new content.
Whts a price to have that same bumper takin off on a 2018 charger I want to swap mines
Hello! That depends on the shop. The bumper does have a lot of steps but most shops will charge $50-90 an hour for probably 2-3 hours of labor.
4:15 an air ratchet saved me so much time on this
Nice! Great tip for anyone who has an air ratchet for sure. Thanks for watching & following along with us!
I have a 2015 charger sxt, would I be able to fit gt front bumper in mine?
All charger parts are compatible, unless your wide body lol
How much would a body shop charge to swap my old damaged bumper and put my new one on
I see it go from $300-$500.
do I need to buy screws and what not if I do a replacement w the srt fascia
Hello! We recommend reusing any screws and hardware that you can. Just replace any screws or broken pieces. We can help you with that if you talk to us in the chat. Take care and visit us at bit.ly/15-21_Charger_Bumper
How did you take the inside screw off you cut that part
Which screw?
Appreciate the excellent video - thank you 👋
Glad it was helpful!
Where are these 10mm bolts inside the fender
Right next to the headlight right behind the fender.
Anybody’s bumper conversion not fit ?
What conversion are you trying to do?
@@ReveMoto charger RT front bumper to charger srt front bumper ikon motor sports. I managed to get it on but I had to leave out one of the pieces that might keep it from having a gap between the hood and the bumper.
What are the bolts size ?
Some are 7mm and 10mm.
❤️❤️❤️
Thank you so much! So glad this video helped out. If you need parts for your vehicle go to www.ReveMoto.com
Didn’t work
Sorry, not sure what you mean by this? Were you not able to remove your Charger front bumper?
we might have to bleed out your brakes
For what? That’s crazy what car do you have to do this just to remove the bumper
All I did was drop a bolt, fuck me....
That happens to all of us ahha. Trust me you keep on work with cars its gonna happen again. Thank you for your service also!! If you need any parts for your car go to www.ReveMoto.com
Thank you!