Video není dostupné.
Omlouváme se.
HVAC Gas Valve Problems and Solutions
Vložit
- čas přidán 15. 08. 2024
- Join this channel to get access to perks:
/ @taddydigest
Wanna Learn more about hvac?
Check out my hvac tips for technicians playist.
• HVAC Tips for Technicians
Fieldpiece SC440 True RMS Clamp Meter
amzn.to/3rdGZ0e
Go check out Fieldpiece Products to learn more about there multimeter the SC440
Fieldpiece Dual-Port Manometer - SDMN5
amzn.to/3SNNLoS
How to set gas pressure for 2 Stage Heat?
Video Link
• Setting the Gas Pressu...
The Dumb and Dumber reference was awesome, Lloyd Christmas is somewhere smiling. Thanks for posting Tad, solid video.
A whole lot of components that I'm not used to I start my new job doing service calls next week I've been doing new construction for the past 8 years I like your content easy to follow and thank you for doing them for us new Jack's doing service calls
Good luck my friend wishing you great success
Thank you for watching
Before taken the inducer motor out I would loosen the burner manifold out. A lot easier
Great as always. Everything is useful in this video. Go on Tad👍Your subscriber from Azerbaijan
Awesome, thank you!
TAD U ARE THE BEST….. I LOVE YOUR VIDEOS . I going from install to tech and all this is GOLD to me.
You are welcome my friend
Thanks for taking the time to make the video.
I would like to know the size of that gas valve fitting to check for gas pressure with the manometer or if you can share a link of where to buy it.
Thank you
Your menometer comes with the fittings
You are best of the best 👌 👍 HI from GOLSTAR healing and cooling
I’m in my 2nd semester of HVac school and ur videos are really good for learning new things
Glad you like them!
never adjust a used belt. always install a new belt and then adjust if needed. put a spare or two in a plastic bag.
I agree then you get the new one you have to re adjust it again
Good video man, I’m starting as comercial pm technician and really looking forward to moving up
You can do it!
It was an awesome video thank you
You can't go off the 24 volt to the gas valve I have had them read 24 but had bad common on board if you have analog volt meter it will read 0
I really like the videos the way you explained and thanks for your hard work.
My pleasure!
Good info Tad ... Thx for posting ...
Great video !
I have a issue with a gas comercial heather that is used in drive tru canopy !
And is not turn on
What could b the issue
The valve or the main gas ?
It’s looks exactly like a carrier rtu but it has yorks shitty controller. Crazy
Great video
Thank you Tod good information all around. However, being new to HVAC, I find it disconcerting when the teacher uses their elbows/fingers to point at something of importance. Please strive to be super clear by using a probe tip or chopstick to point and maintain the point for three or four seconds for a screenshot reference. Thank you.
Great point
Good video, thank you
You're welcome
Great video bro
Thank You 😊
Hello. great content. I Have a question … have you ever experienced a commercial customer call you with a complaint of natural gas odor inside a store? I’m checking these units up and down but am almost out of theories. Is there a premature opening of the gas valve or maybe an induction motor with a leak somewhere? Pretty windy on the roof maybe it needs a exhaust extension brought up higher.
could be a bad board or something like that where its sending power to gas valve and not igniting.
or regulator vent is leaking
Can you use Teflon instead of thread sealant
Do you have a video on how to clock the meter on a unit like this?
No sir but I can make one
Nice video. How did you manage to have a replacement valve on hand?
I did not I ordered it it came in in 2 days
I am an hour and a 1/2 from Nashville to an hour
2 hours from Memphis
One hour from Jackson
I have suppliers all over near me
Man that was a wealth of knowledge!! Thanks tad! What size of manometer fittings do you typically use? I'm in commercial hvac in Texas but still green.
Hey Aaron send me an email thank you so much for joining and being a member
tadfuller1@gmail.com
Glad I could help
They are all standard simple barbed fitting works should come with manometer
Keep doing these vids. I like it 👍
Thanks, will do!
Good video
Thanks Hector
I have some guides I want
To send you
Please send me an email at tadfuller1@gmail.com
Hey great video, but did have one question, you normally check your sensor by ohms reading and not continuity?
Normally I check the resistance reading
Continuity is also a good check
Its generally going to be an ohms reading. Continuity is generally for broken wires. Either way, its the same mode on your meter to look for low ohms or O.L.
It will work the same way I use continuity
which membership is with the private videos and support?
level 3 😁
I would hate to ask but do u have any Carrier/Trane/Rheem unit trouble shoot
I'm not sure if I do or not
I think I do but if I don't I'll have some soon
Why all the rust on the gas pipes and disconnect switches ?? What area of the US is this ??
Tennessee near Nashville
Pipes rust everywhere doesnt matter the location. Even indoors. In salty air, close by oceans, is where metal will rust much faster.
hi what are they symptoms when dirty burners ?
flame will not spread across burners if dirty
@@TaddyDigest thanks
@@TaddyDigest what's causing mini explosions /bang on commercial RTU ? gas furnace
Hey tad quick question how did you know that sensor was supposed to be 10k ohm? I haven't diagnosed that sensor before but on the ODA and SAT MAT sensors RTA sensors etc how do you check those? Is that with a 10 k ohm chart? And has to match the same ambient temp outside???
Hey send me an email I have some guides for you
tadfuller1@gmail.com
yes I use a chart I can send you what I have
@@TaddyDigest just did👍
Awesome
👍👍
Awesome video, giveaway
Microchannel is Cheap coil .
I think they actually cost more and are have better efficiency. But on the other hand, they break easier and are harder to repair. We require them to have hail guards on the rooftops units in our facility.
Your pipe doping skills are lacking here. First, you gotta clean the old threads with a wire brush. Next, apply a thin coat (more is not better). Last, you have to make sure to not get any pipe dope on the end of the pipe (you definitely got a big gob on the end of the pipe) so that it doesn't go into the system and cause problems. A final recommendation is that cogged belts are superior to those straight, standard belts.
thanks for watching and for the great tips 😀 👍
@@TaddyDigest I hope that didnt come as me being a jerk. Its very hard to strike a balance between criticism and not coming off as being insulting or disrespectful. (The same problem happens with text messages too Ive found.) I did very much enjoy your video here and look forward to more.
Friends look out for each other friends say something when others say nothing.
It's better to say something
Iron sharpening Iron
Thanks brother.
Big fan of your videos@Taddy_Digest
Thank you brother. I really appreciate your support and I appreciate you watch the videos