Video není dostupné.
Omlouváme se.
10 Plumbing MISTAKES Not To Make! | GOT2LEARN
Vložit
- čas přidán 4. 07. 2022
- Join as a LIEUTENANT to chat in my Discord server / discord
/ @got2learn
Stuff I used in this video (Amazon affiliate links):
#1- Lead-free flux: amzn.to/3OPLbNK
#2- Lead-free PREMIUM solder: amzn.to/3ONh0qw
#3- RIDGID 14" Pipe wrench: amzn.to/3At5BaR
#4- OATEY pipe cleaner: amzn.to/3bGEJKa
#5- Plumber's strap: amzn.to/3urRBdO
#6- Sharkbite Depth gauge tool: amzn.to/3NMToAO
DISCLAIMER: Got2Learn is NOT responsible for any damage done to a property of which the plumbing wasn't done by a professional, I do not recommend doing your own plumbing if you are unsure about what you are doing, always hire a LICENSED contractor when doing any type of plumbing so you can be covered by insurances if something does happen, these videos are for entertainment purposes only!
Stuff I used in this video (Amazon affiliate links):
#1- Lead-free flux: amzn.to/3OPLbNK
#2- Lead-free PREMIUM solder: amzn.to/3ONh0qw
#3- RIDGID 14" Pipe wrench: amzn.to/3At5BaR
#4- OATEY pipe cleaner: amzn.to/3bGEJKa
#5- Plumber's strap: amzn.to/3urRBdO
#6- Sharkbite Depth gauge tool: amzn.to/3NMToAO
He's back from the dead 😂
So he voted Democrat? Bwahahahaha!
@@saltycreole2673 isn't he Canadian?
Yup
Thanks so much for your informative channel. I became a new homeowner a little over 2 years ago and didn't know anything about plumbing. Now I've replaced my entire well system with filtration - acid neutralization - and softening while separating my hose bibs from my treated water, re-ran 50 amp multiconductor electrical to my garage along with a generator feed to keep the noise away from the house, repaired acid decayed copper pipe which burst and began an entire decrepit bathroom gut and remodel with new Pex lines to the bath, toilet, and sink, along with a proper fridge water compression outlet since I had that wall open, moved the toilet waste drain so it would be the proper 12" from the wall, installed bypass valves for the on demand water heater flush, and so much more like that. I used your videos most, and I just wanted to let you know how much I appreciate your straight to the point and thorough coverage of your topics. 👏 👏 👏
For the well system in CA, Clean Water Store was excellent and gave me the instructions that i needed for the design, the plumber who I hired to tell me if I messed it up came and only added a couple of small helpful things and told me it's good to go. Wanna give them a shout out too because they have so much instructional content and answer their phone for questions.
Awesome man, thank you so much for sharing this with me 😇😇😇
Glad your back, always a great reference point. Just finished my 1st complete year of plumbing and watched your videos constantly 💯
🤘🤘🤘
Glad to see you back! I think you mixed up the verbal description at 5:04, the one on the top seems to have the glue on both fittings, but the bottom one doesn’t. I definitely liked the tips on installing chrome bathroom fittings.
Yup, thanks for the cue 🤦♂️🤦♂️🤦♂️
Frickin’ awesome video! U present clear, concise advise with excellent examples. The things that u talk abt are spot on. U don’t spend any time talking, talking, talking abt things that aren’t relevant to helping people avoid mistakes. Yr videos are top notch. I just learned several things that will help me. Thank you!
🙏🙏🙏
no Tef tape on compression thread period. This guy! This Is the Guy!
I had terrible management in my early years and this channel trained me up. No joke. Years later I'm doing 7 figure sales for the top wholesaler in our city.
I recommend this channel all the time to everyone. Thank you Got2Learn. keep being the best!
Awesomeeee!!!!!
If all fittings were rust and corrosion-resistant, I would agree with that statement. But a lot of products from the big box stores are made with cheap metals, and two layers of teflon tape are insurance so you can remove the nut in the future. This especially applies under the kitchen sink, where drips, leaks and other problems happen in the dark. A compression valve for a toilet bowl is usually out in the open, and easier to diagnose. Flex hoses are the biggest source of leaks that introduce corrosion damage to plumbing connections. Next biggest cause, outdoors at least, is rain, salt, and sun.
What I like most about this video is that he 100 percent installed thread tape correctly even though it was to a fitting that didn't require thread tape.
Thanks for posting that on the toilet supply line and teflon tape on compression fittings. Another pet peeve is pipe dope on compresion fittings and 2 piece p traps.
I use t+2 dope on the 1/2 in compression threads of angle stops to allow me to get a tighter seal because many times I have had a slow drip come from them without dope. I have tried many different ways to prevent the small leak.
As the man who is known as the "plumbing expert" at the Ace Hardware store I work at, I find the videos to be very useful. Many thanks for making me look good!
Love the content man! Just started plumbing few months ago learned so much from just watching your videos when I get home and apply it next day at work 👍🏽 🙏🏾
👌👌👌🙏🙏🙏
I have been a plumber for 42 years, and you have a great video. It’s a good list of the most common things DIY,res get wrong.
🙏🙏🙏
Welcome back! The information in your videos is very good and very important for both professionals and the rest of us. Please keep posting - do a great job.Thank you!!
🙏🙏🙏
Great video as always! Welcome back 👍
Hhey hey, thanks man!!!
Great tips. The rubber strap wrench and garden hose tips is a game changer.
🙏🙏🙏
This is great advice for DIYers, noobs & novices.
Pay att’n. & do it right the first time !!
He's back! Making CZcams videos is as addictive as crack ;)
he is back!!!!!!!!!!! WE MISSED YOU - OUR BROTHER IN THE NORTH !!! WELCOME BACK !!!!!!!!!!!!!
I have never used primer when I glue pvc. Done 1000s of feet of it and never had a problem. I do commercial fish systems though, not stuff in walls in a home.
in the early days of pvc pipe, primer was not available, but the pvc manufacturers recommended roughing the ends of the pipe and insides of fittings to break the gloss with medium grit sandpaper before gluing the joints together. primer became available to speed up the process but sanding the connections still works today if you don't have any primer.
When i used to do rough plumbing, the toilet always had its own vent, and I use clear cleaner when doing repairs when working in a finished environment, if you spill that purple primer onto finished floors, call your insurance company. LoL
Some more great tips! On stop valves that use a nut and ferrule you don’t have to use thread sealant on the threads because that’s not what is actually doing the ‘sealing’. Just put a little bit on the inside of the valve where the ferrule sits and that’s all you need.
I use dope on threads just for lubrication and in rare repair occasions I will put tape so it hits the ferrule and unit sealing point. Only for the most terrible situations. Or if I only have one chance to turn water back on and it can't be turned back off.
@@beerbeforebreakfast I wouldn’t want to put thread tape on them in case some there was some that shot into the supply line in a rare case. As long as it’s not the old TrueBlue that turns into thread locker over time lubricating them isn’t too bad
@@doublej5171 yeah I know what you mean. I have figured it out, I wrap the tape about 80% on threads of the fitting so that about 1/8th inch will fold in the the sealing point when all said and done. Works 100% of the times I've had to do it. Not enough excess to cause any issues. Only place to be concerned would be kitchen faucet if it's new and fancy. They sometimes have micro filters in the supply lines right at the 3/8 nut that goes to shutoff. Those clog so easy.
Love all the examples of how to do it the right way. Thanks
🙏🙏🙏
great advice, I am a do it yourself guy and I love videos like this.
Thanks 👍!!!
Point of order. RoHS has been the standard in electronics since 2003 and most makers were in compliance with the proposed rules by 2000. So any big box home improvement store will not have leaded electronics solder. You can order solder with lead (Pb) from vendors such as Digikey or if you are in a shop that deals directly with repair/hobby electronics you might get it on the shelf. Not all electronics solder has lead (Pb) in it.
My understanding is that teflon tape isn't only used for sealing/waterproofing purposes, but to act as lubricant between the two threads. If not used the threads can bite into each other, making it feel like it is turned all the way in, when it is not.
Thus it's a good idea to even use it on supply values and other connections with their own seals.
Correct, and straight treads do not need teflon as they seal with a gasket ;)
I personally use either a silicone/PTFE lube or a joint compound on most fittings. They do a significantly better job than tape of actually lubricating the threads and makes it easier to fully tighten.
Yes, for example, a 3 inch pvc threaded clean out cap, Teflon or thread tape would work equally as well. Without it, the fitting will not seat completely due to friction or possible snapped hub from attempting to overtighten. Doesn't take much, 2 wraps at most for lubrication purposes I say.
@@Got2Learn 3rd gen plumber for my whole life and we always laugh when we see teflon on compression or flare fittings and supply lines
@@revoevom1490 😆
Great video, some states doesn't allow AAV - mechanical vents.
Good to know!
Man I love sharkbites. When installed correctly of course. :)
Binge watching your videos right now. Lots of useful information. I do put teflon tape on compression fittings though because it makes them easier to tighten (not to make them seal better because as you have said it doesn't). Not on the outlet end where there is a rubber seal but on the end with the brass compression ring. I usually only do this behind toilets and under sinks where I have a harder time getting good leverage.
😎🤜🤛
Welcome back!!!!!!!
We've missed you and your wisdom!!!!
Keep up the good work!!!!!
👋🙏🙏🙏
I always put some sort of sealant or lubricant on any threads so I can easily remove them in the future. When I'm plumbing, I just use what's handy, which is often teflon tape or pipe dope.
Me too...Don't forget to share if you can, really helps the channel, thanks!!!
Glad you are back. It has been a long wait.
Oatey actually recommends applying primer to the inside of the fitting, then to the exterior of the pipe, then the inside of the fitting again, then applying cement to the exterior of the pipe, then to the inside of the fitting, then the exterior of the pipe, then FINALLY joining them with a 1/4 turn twisting motion. The also (of course) recommend cleaner, probably because they sell it. I'm no professional plumber, but I've not seen anyone use it. And if I have a piece of dirty pipe, I just wipe it down with Windex.
If I have a fitting that absolutely can't be leaking and I've got 3 floors of water waiting on my repair.....I use cleaner, primer and good cement! Can't take chances on major repairs like that. But 98% of the time I do not use cleaner.
It is a HUGE treat to have another video ... Thanks again for all your hard work and education in these videos!!! so great to have you back
🙏🙏🙏😇😇😇
Love your video’s!
I am doing my first year apprenticeship and i watch your videos all the time for tips and tricks! Would love to see more new tools that could help that you recommend thank you
🙏🙏🙏
Thank you brother for sharing the wealth of your knowledge.
This is the kind of sharing that makes us all rich
Glad to see anew video from you! Great stuff as always. We appreciate all the time and effort you put in to these.
Always ''Buck" with a larger wrench!
I've been plumbing for 8 years, and still I enjoy watching your videos
Thanks man keep plumin'
Awesome as always!!! Great info and great delivery. Glad to see you posting.
🙏🙏🙏🙏🙏🙏
As a professional plumber I love your videos there are always hidden gems to be learned
Thank you so much 🙏🙏🙏
@@Got2Learn NP thanks for the content!
@@Plumberslashwaterbender 🙏🤘👌
All great tips as usual! Thanks and glad you're back!
🤘🤘🤘🙏🙏🙏
Love the channel, glad you are back.
🙏🙏🙏
Hey, Got2Learn! Good to see you back!! This was an excellent video as always! You would be a fantastic trades instructor!
🙏🙏🙏
"the sound of hardened teeth crunching"....
😯 the sound of failure
Yessss
There is a study you can read online where it shows unprimed joints are stronger.
Missed the videos glad ur back !
More to come!
Actually IPC, I believe could be UPC, states you only need to use primer on PVC if the pipe is presurized. Or if the AHJ or local code requires it.
I got one of those blue things.. never knew what it could be used on.. it always slips off everythng
This is a great video for beginners. I think most plumbers have made a couple of these mistakes at least
🤘🤘🤘
Mechanical vents should be installed above the water level of the sink, washer ,etc.
This is plumbing 101!!!
At 5min 20 sec. Turn pipe as you push in . Read the can . Then read it again
Very informative, learned a few new things. Thanks! 👍👍
Glad to hear it!!!!
Thank you, thank you, thank you for such info Got2Learn. You ROCK!!! DVD:)
There for a minute I thought I was seeing things and there it was a G2L video , thanks brother glad to see you back from mars Lol , I sure hope all is well with you and your family and hope to see you in many more to come, thanks again
Thanks man!!!
3:10 lmao 😂🤣🤣🤣 dude's balls hanging
Very informative. Thanks.
🙏🙏🙏
Another thing I would add is to make sure your Ts and wyes are orientated in the proper direction. Never bullnose a T.
****** CORRECTION ****** In many parts of the world electronics are required to be ROHS compliant meaning they must be lead free. Because of this lead free solder is becoming more and more common. Check the label. Also plumbers flux can be used in conjunction with rosin core solder to increase its capillary action on copper. As a side note NASA requires that solder used for mission equipment contain lead to minimize dendritic complications at the solder joints.
4:07 Hold up, i thought the tape was to reduce friction and make it easier to tighten, are you saying I shouldn't do that?
Not for straight threads, only on tapered threads, watch this video here: czcams.com/video/G4EijapY7vw/video.html
need the NSF stamp to use on potable water.
100%
Teflon tape/pipe dope on anything other than pipe threads tells me that a hack did the work.
Glad you're back!
Excellent as usual 👍🏻
welcome back, I missed your videos 😉👍
Love your videos. Thanks for the tips!
Most important for plumbers, Don't bite your finger nails !
Always great useful information.
🙏🙏🙏
If you have S-traps installed how can you replace them with a P-trap?
Great question! I have a video just on this: czcams.com/video/pmN88UvZfDI/video.html&ab_channel=Got2Learn
Thank you, guys!
This was GOLD, thanks.
Thanks for that 🤘🤘🤘
I know you're not supposed to use pipe tape on the toilet valves, but I have not been able to get them to not leak without it.
Your valve might be bad in that cases
Welcome back!
The glue also melts a micro layer of PVC like welding literally
You're back!
The purple one is grape flavored. The yellow one is thick and pasty and tastes like glue.
Great tips, thanks
Very good tips. Thanks.
🙏🙏🙏
Great to hear from you again.
🙏🙏
Technically lead in electronic solder is getting phased out however there's probably a lot of old rolls sitting around peoples houses.
Exactly.
Bro! I completely missed you made a video. 😱 You've been missed!
This channel is so informative. 👍
🙏🙏🙏😇😇😇
3:03: Issue with diagram....Testicles not hanging low enough.
LOLLLLLL
You are the best. Keep it up !!😊
Thank you so much 😀!!!
I see videos , mostly DIY , but some " PROS " too , that NEVER de burr pipe , metal or plastic . When you see them uneducated or simply taking shortcuts at the expense of the job , RUN AWAY . Some will even argue that you don't know what your talking about . Beware the Big Mouths !
💯💯💯
Hey, welcome back!
👋
Yay! you are back
👌👌👌
Thanks.
I love this guys videos wish he wasn’t gone for so long and he stsys
😇😇😇🙏🙏🙏
but I was looking for a simple method of soldering pipes where the water keeps falling back into the place you want to solder
I always get something from your videos. Thanks
Guess I'm not as bad as I thought -- I've never done any of these things.
I'd like to see a comparison of where Teflon tape is preferred over plumber's putty, if anywhre.
😇😇😇
Ooops, I made the @4:35 of the video mistake by using teflon tape on compression fitting :(...
love it thanks my friend
@Got2Learn 6:48 To prevent this.... WASH YOUR HANDS! 😜😜😂😂
5:12 I think those are reversed but yes that is a common mistake especially when people start rushing.
Yup I reversed lol 🤦♂️
S trap is fine if toilet is vented up to code 15" I think
Nice to hear from you mon ami 👍
You too buddy :)
I just go with PEX and cramp and save the soldering...lol
I agree with the video, I used to sweat a lot of pipes, and one time made the mistake of using the wrong kind of solder, and it was a very expensive lesson in the material and labor to go back and fix it later. I was not a big fan of PEX in the beginning mainly because I thought "the art" of sweating pipe would be lost... But I think it is approved everywhere for home use right now and the cost difference is obviously a huge Factor not to mention time....