Solve as soon as possible: broken 2.0HDI 163 RHH injector holder, leaking injector seal
Vložit
- čas přidán 10. 09. 2024
- If you can smell exhaust gasses and some smoke can be seen on top of the 2.0HDI 163 (RHH) engine, then most probably you have a leaking injector seal, in most cases, due to broken injector holder.
This is second time I am having a leaking injector seal. First time the holder was fine, but now it was broken. In this video you can see me repairing this issue.
I have same engine on my 308cc. All video of your channel is the best one that I've ever seen. I appreciate it for sharing. I'm looking forward your new video about Vacuum pump and Thermostat.
Hi, nice to hear that it is helpfull for somebody ☺️ is your vacuum pump ticking?
@@rustoil Hi.😊 Yes. clicking sound is louder and louder as time goes by. and sometimes sounds prrrrff.. after engine is shut off. It's difficult to explain in word. lol
Most likely that connection mechanism to the camshaft has wear and no it is loose. I will try to investigate on mine and will definatelly film it 😉
The fastener must have been too tight! Tighten it to 7 nm and then 55 degrees (that's 7 clicks on my torque wrench). That's remarkebly untight, so the danger of tightening them too much is real!
Yes, I have mentioned required torque and additional angle for tightening.
Wow, man, you made my day !!! Awesome ! I have first diesel so I´m not familiar with disassembling of injectors (even if I have had one direct injection petrol, but it did not need this kind of service) and my mechanic refuses me about resealing injectors due to possible damage or at least stucked bolts and injectors, but now I´m thrilled to do it by myself :) Thx, take care ! Subscribed :)
Hi, thanks. Just be sure to remove air from the fuel system before starting the engine. I have heard, that injectors can get stuck if they get air with fuel.
@@rustoil Thx for advice, I´ll look it up. Looking forward to next videos !
Well filmed video, it has helped me a lot doing my own repair! Never touched injectors before but after this video I had the courage to do it.
And it's exactly the same on a Ford Mondeo 2.0 TDCi (euro 5 engine) which is great.
I just have a question, at 17:25 I can see that you were struggling to attach the fuel return lines. How much force did you use to press them into place? When I tried to press them in, none of them entered the hole in the injector completely. They are just sitting loosely right now. I was afraid too much force was going to break them, so I left them like that. Should I try to press harder?
Hi. Thanks you for your comment. Well, firstly check if those locks are completely ulocked, then those pipes should go in with some force, created by rubber seals. Be carefull not to brake any plastic part.
Hello there. This video helps a lot. Can you tell me, what size is the bended wrench, that you use to turn the injector?
Good job!
Ваше видео мне очень помогло. Огромное спасибо
Excellent thank you 😊
Hi, thank you for all the videos you make on this engine and the C5 as a car! Stay healthy and safe and I wish you the very best! I have a couple questions that came up during watching your video:
1) Now, one thing that was on my mind (I am an amateur when it comes to engines) - when you work on high pressure systems like the one in the video, are there any precautions you take when removing the fuel rail or the high pressure fuel lines from the rail to the injectors? Is there like a depressurize procedure of some sort in the Lexia (like the one for the suspension) or a pure mechanical one to make sure that something doesn't fly off during disassembling those specific parts?
2) When you started the engine, I heard a very familiar sound from the vacuum pump "clicking" (I don't know how to explain it better). I have the same car with the same engine and sound. The way I know it is from there is that a friend of mine had a stethoscope with a long probe at the end and when you put the probe on the vacuum pump, you can hear the clicking in your ears. You can check it for yourself to see if that's the case with you. If it were to be the case, would you buy a new one and replace it or would you use the one from the spare engine to see if that one is better? Either way, would love to see some day a video about this, because I have seen a fair share of these engines with that "ticking" noice!
Cheers from Bulgaria!
Alexander
Hi! Thanks for your support :)
1) no specific procedure to release the preassure has to be taken, as you can see in the video. All pressure goes away when engine is shut down.
2) yes, the vacuum pump is ticking, i will try to replace it. as you have probably seen, I have a spare engine, it had vacuum pump on it, hope that it is better and will not be ticking.
I will make a video when replacing it for sure :)
@@rustoil Thanks for the quick answer! Have a great day and a productive week! Looking forward to your next videos! Cheers! :)
Did you ever change the vacuum pump? Was the ticking coming from it?@@rustoil
I am living with the ticking vacuum pump, does not bother very much when the hood is closed ;)
Thanks for the answer! Good to hear that. I have same kind of ticking noise on startup. I was fearing that maybe it is the valves that are ticking@@rustoil
My problem is that the motor has locked up, will a faulty injector do this? There is a white foam that smells a little like Diesel fuel in the overflow tank.
This is happened to my c3 1.6ehdi 92 injection holder cracking and cause smoke under the hood and engine not working properly before i smell something like its not burning the fuel well. Maybe this is the reason?
Yep, the same... Its a bit scary to drive long trips, car can get non-runing...
@@rustoil After the replacement there are no more problems?
After that time everything ok with injectors.
Will that show up in computer diagnostics?
Hey man, where did you get the book at 16.08? Is that service book ? Can you help us whit this instructions ?
Hi. I have found this sheet on google, in some forum.
Hi, can you tell me which wrench number (mm) was used to loosen up the injector at 7:46? I am trying to make the same tool. Thanks
Cant remember exactly, maybe 15mm.
@@rustoil Hi, since you have experience with these engines, my injector holder was broken and I replaced it 6 months ago. Now again the same cylinder (cylinder 2, the same one as in your video), the same injector holder broke again. Other injector holders are never touched, they are original. But this one now broke again. Do you have any idea why something like this occurs again?
Maybe the holder bolt is overtightened.
I have a 2006 MOY C5 Diesel which I think has the 163Kw Diesel. The injector set up is not like this.
Hi,
Thank you for the excellent video. i would like to ask if you have ever dismantled one of these type injectors to clean them? I done a leak off test on my injectors a while ago and my mechanic said that fuel was too much coming out of leak off pipes. would you know what he rate of fuel should be leaking off from pipes?
Thank you
Sid
Hi. Thanks for your comment. I havent disassembled any injector yet. If they leak too much, look for replacement valves on ebay or aliexpress, there are usable alternatives as long as I know.
Man please help, I have done pretty the same way but, after putting all together I have engine fault, and check light in board... can you help with some solutions or checks? Much appreciated!
Hi. Well, I would check everything that I have touched when working on the car and try to find anything what can be loose and not connected properly.
@@rustoil yes all connected as it was ... but I see in the fuel pipe it have areea with different colours, like is air inside.. it's not all pipe with the same colour...
Does the car start?
Car start normal, but when it start it make some sort of sound like diesel pump try to pomp fuel, or make some checking at the fuel pipe...
Dont know what to say, not very clear if there is any problem if the car is running, regarding the check engine, diagnostic tool should be connected.
Those injector clamps are made of the weakest metal I have ever encountered!
I'm fabricating my own from 10mm mild steel barstock.
Hi. Could you share any photos of it?
👍😉