FULL DETAIL EGR CLEAN DIESEL 1kd-Ftv - TOYOTA Land Cruiser Prado or Hilux
Vložit
- čas přidán 4. 12. 2019
- This is a TOYOTA HILUX Prado 120 almost the same 150 also very similar.
Lots of tips, tricks & information included so please listen carefully.
Toyota Hilux egr clean.
Do some of this replacing Injectors.
Happy feuds night or weekend watching movie length egr clean!
LC120 LC150
TOYOTA LANDCRUISER
1kd-ftv Diesel
Fourby4diesel
J120 J150
LEXUS
My injector replacement videos are very similar to this - Auta a dopravní prostředky
Can't believe I just sat here for an hour and 47 minutes, watching a CZcams video. Most of the time, I get over it within a few minutes because people have really poor camera angles, neglect to talk through certain processes and just expect people to know the little details that comes with experience and just all round poor quality videos.
Dead set best instructional video I've ever seen.
You're a bloody legend. Cheers
I’ve spent almost two days to did this, weather outside 5C, rainy and windy, garage without heating, but i did it :) EGR was fully caked, throttle body, quite nice, rest also caked, worst things upside down bolts. Thank you Anthony and greetings from Poland.
The only complete EGR clean video out there which I watched to the end & I "dared you"
Is the blow-by needed for the gas in the engine or can you go some were els with it and not return it to the intake. Pleas tell me.
Thanks mate your run down of this procedure is by far the most clear and educational video of the 1kd I’ve seen 👍
Excellent work, greatly appreciate the effort you put into showing us how to maintain our 1KD-FTV and vehicle.
Anthony, just commenting to say thanks for the video. I watched it in its entirety first then watched it, pressed pause and play while doing the job. Invaluable info and the car is running great now (had a cracked MAP filter too). 2007 1KD Prado with 404,000km on the clock. Thanks again!!
Can't thank you enough Anthony watched this video & had a crack at cleaning my 1kd today. I think mine has been done some time in the past because the build up was nowhere near some of the ones you've shown us. But none the less it's a messy job but done. Thank you again.
Just want to say a big thankyou to you Anthony! I really appreciate all the knowledge you put out for all of us. I watched this in advance to see if i could do it myself then followed it step by step. Only issue I had was the 10mm upside down bolt left side of egr, quick run to the shop for the right tool and it was allgood. 103xxxk 2015 trd. Barley needed a clean but I did it anyway, 7mm plate. Ute feels noticeably faster and without a doubt be running better in the long run. Cheers mate love your work.
Watched it to the end, well done, Ryobi have been good to me over the last 20 years, I have a 1kz-te, but I learnt some things anyway. Many thanks.
This is the best produced, detailed and informative video I've seen.
I will now follow through and look at others previously produced and keep an eye out for future videos.
Great job thanks
Thanks for taking the time to make this video I for one truly appreciate it
Thank you sir, got this job done today. Was thinking as I was undoing everything “I’m not going to be able to get these back in” but was so much easier putting it back together. Kaon didn’t end up sending me a plate so I didn’t bother chasing it or installing.
Great video. I did mine two weeks ago. I saved $$$ and happy like a pig in mud. Now I watch your videos when I get a chance. Lot of great information for free. Thank you so much. :)
Was umming and ahing about doing this for ages. Probably the third time I watched this video I gave it a crack and it was so much easier than I thought. Couple of fidly bits with those hard to reach clips but saved myself a shitload of cash. Really appreciate the detail in this video. Definetely wouldn't have even considered it without it. The egr valve was maybe a bit worse than the one on here. Can appreciate the time it takes to clean them.. thanks again!
Very comprehensive and professional. Highly recommend watch the complete video for D4d hilux owners. Answered alot of questions for me.
Bluddy brilliant video ol mate. I've only just stumbled across this channel recently and the missus is getting jack of everytime she looks and sees what I am watching it's your videos!
Doesnt matter because I can hand the remote over and go out to the shed and watch these videos whilst my bonnet is up and the plastic removed.
Great work mate
I've just cleaned my EGR valve on my 150 using a combination of this video and the workshop manual. Your advise made it so much easier than I thought. Great video mate.
Side note: After I did the job my fuel economy went from approx 12.5ltr /100km down to 9.6. I can't believe the difference it made.
wow! that's a huge difference mate! did you use a full blanking plate or the one with the 7mm hole?
@@jonyjonsyhe only mentioned cleaning, so I'd say it's standard
I had to clean and replace the egr valve on my landcruiser and this video was absolutely amazing. I followed it to the letter. Top notch thank you
Mate, perfect lock down activity, got it done this arvo, major clean out needed so glad I got in there, took heaps of crap outta my valve and elbow. Couldn’t have done it with out you mate so cheers heaps...and yep you dared us!
Did this job today after watching this a few times end to end. The Hilux is humming again! Thanks!
Hey ant, love your vids very comprehensive and bucket loads of valuable info. This vid helped heaps saved me heaps of coin and got the 1kd ftv breathing properly again. Can’t thank u enough thanks mate.
I've not done this job for 10 years thanks for the refresher course . I like the egr restrictor plate compared to blocking it off .
Great video !
Awesome Video Anthony, used it to disassemble my prado 150 EGR and clean it up.
Thankyou for all the great content on the 1KD-FTV.
Just cleaned my egr on my 2015 hilux with 84,000km and I was shocked how bad it was. It’s stock standard, filthy EGR! Thanks for the tips.
just did my 2015 hilux with 105k, I was impressed egr piping was pretty clean did not really need a clean but did it anyway and put the 7mm plate in as well...happy days
I dared you to rattle em up 🤣, awesome video, heaps of information that was clear and understandable, plenty of tips. Watched the whole way through. Will watch many more videos, and will have a crack at this myself soon. Cheers mate, really appreciate you taking the time to make decent video's like this! Love your attitude and how you spin a yarn too. Subscribed.
Watched a few time before attempting myself on my 120 Prado.
You make it look a lot easier then I did.
A huge thank you. & I Dare You.
Great video so far and very educational I’ve watched some of your other videos too and they are all great
I’ve got a 2013 hilux sr5 and I brought new and a couple months after I brought it I got a very good outfit in Chch Nz to remap the ecu and I wanted to blank off the egr valve but they said it was easier to just shut it off or deactivate it they put a bolt behind the actuator to stop it opening or closing or what ever it does and did what ever they needed to the ecu to stop the egr light coming on
It doesn’t blow any smoke and it runs extremely well I’ve also had a 3” pipe put on from the turbo back so it breathes properly it’s now done 200’000kms I change the oil every 10’000kms and after I change the oil I use cheap oil and tip it in and keep tipping it in till the it runs out the sump clean usually use 4-5 Litres then I put the bung back in and fill with 0w30 fully sinthetic oil and the oil stays clear and transparent on the stick for at least 6-7000kms then slowly darkens up but I can still see the metal of the dipstick through the oil
I’m not a mechanic but I’m sure the motor stays so clean because it’s not circulating the dirty air back into the motor
I would love to here your thoughts on this and what I have had done thanks very much and happy new year to you and everyone
I’m going to finish watching your video
Cheers
Bob
Good onya Anthony, bought a second hand Hilux and did this straight away. Lucky I did - it was caked. 170k - prob had never been done. 7mm plate installed while I was there. Haven’t driven yet but idled smoother and quieter on startup. Thanks for your videos.
Ive been wanting to do this clean for a while and after watching im ready to give it a go. very informative and greatly appreciated for taking some time out of your day and filming it for myself and others to educate themselves. also i dared you haha .
Great video.
Did my Hilux today , 160k and it was caked and I’m glad I did the job. It ended up being pretty straight forward. I was putting it off cause I thought it was going to be a pain. The longest part was removing the plug on the common rail to install the plate.
Ended up with a whistle from the plate on cold start up but it goes away when it warms up.
Car runs better with a smother idle and more throttle response.
Just have to repeat for my prado now!
Another awesome video from the Assassin of Soot & The Killer of Carbon. Thanks. Now I need to save up for injectors! Much appreciated.
This is a video I’ve been waiting for someone to make for a long time
Thanks I have a Mitsubishi L200 4D56 turbo engine. Now I know how to clean my EGR value , you doing a very good take up.
Good to see a very comprehensive video. looking at this to do my J120 soon. will definitely pull it back out when I do it. "I dared you" Thank you for a Great video.
I have a 1kz-te learning, i know this is the wrong series, but what to expect, this is just an incredible video
I did the clean this weekend. I can see why you don't do this anymore it's a s$%t job and it gets everywhere. My Prado 150 has just clocked over 190k it was pretty bad, hopefully won't have to do it again, thanks KAON. Took it for a drive for about 20km after doing it and dropped the oil, had a look up the sump hole with my inspection camera at the pickup strainer all clear. changed oil and filters budda boom budda bing.
Then found one of my CV's is buggered which probably means another buggered weekend.
Thanks for the videos keep up the great work, oh and i use the same Ryobi impact driver too it is a pretty good tool.
Great video I am new to owning a hilux and am confident in doing a egr clean after watching your video thank you for your time
Love your work 4x. Thanks for the education... and I dared you.
Mate great vid just did the whole procedure as you've described. Thanks heaps.
I was waiting for a dentist joke when you vacuum the manifold. Awesome vid Anthony
Greetings from Trinidad and Tobago. Great stuff. Keep them coming.
WoW!!! Awesome stuff...
Iv'e done the same as in the video (small diffrences to the 1KD in the Fortuner in SA) but non the less the same out come...
Keep up the good work and the video's. Always something new to learn from you👌
Cheers Anthony for the great video.And info that's beneficial for us home mechanics... and the addition of the blank plate info is great ... I dare you to do more videos... cheers
Great video all the way to the end. talking all the way through with reasons and how.
Great to watch someone else doing it for a change, done mine yesterday ,still trying to get my hands clean 🧼 and yes I had gloves on
Awesome video, I did my EGR clean watching this.. thankyou...
Anthony, thank you bud 🙏 very educational and love the humor. I just completed the clean on my 05 Hilux, it was different (maybe slightly easier) then my 08 model.. definitely watch these videos till the end always extra information, I dare you 😆
What a fantastic video!! More please. Very well narrated.
Thanks mate that was very informative and has given me the confidence to do it myself...cheers
what a great vid loaded with info. feel like i may have wasted my time instaling a catch can now ;) im due to change injectors so this cleaning will be a must. thanks for the info m8. from. over here in nz
Mate I don’t even own a diesel 4x4 and watched the lot. Was very interesting. Thank you
Thanks Anthony, Legend! completed full ERG clean on 2010 Prado, (without Oil Catch Can) most tar like substance caught in EGR control valve very little at elbow at Inlet Manifold. Saw improvement in Load percentage 15.9 down to 14.5% and approx. 0% error on EGR position @ 800 rpm 85 degrees. Hope to get down for Injector change after Covid 19.
So your Obd never shows EGR error?
Thanks for video
I’ve just done my hilux to say the least it’s not straight forward as stuff breaks bolt get stuck etc on a 4wd that actually gets used on red roads a lot not a black tarmac people mover.
I did the water pump timing belt removed manifold cleaned egr and blanked it off with the old 7mm plate
Has taken all Easter break work is done now cheers
Thanks Anthony great video I watched 3 times I have 2014 hilux 52000k and egr on albo bend completely caked runs like dream now but must do map filter clean K&S and don’t forget 7m plate works well👍👍👍
Thanks much my friend for the education i have watch the hold video to the end,
I sincerely appreciate it.
Thank you.
I watched to the end mate, great video
bloody good. Covers everything!!! cheers
Perfect video..watched to the end have a 2008 Hilux same engine found your video very helpful...thanks a million
Mate thank you so much i followed this video for my hilux and prado and it worked a treat A++++++ Video
I watched the whole thing & I dared you", thanks Matey good descriptive job just what I needed
Nice work Anthony thanks for the detailed vid. I’d be taking the wiring harness off definitely don’t need to be stripping heads of bolts. I recon I’ll do the manifold, erg & injectors together at 279,000km its worth doing all together with new gaskets. Looking good bro👍
Спасибо тебе большое, чистка впуска не сложный процесс, но твое видео помогает и воодушевляет. Долго не решался начать. Еще раз спасибо
Just done it. Took 6 hours, including the install of the 7mm plate and looking for a dropped bolt that took about an hour to find. Thanks for the video Ant, helped a lot!
Legend as always, dared but gently, practice is knowledge 👍
Excellent work man, I'm learning here in Honduras to work in my Hilux 4x4 2012. Greetings
Hi friend your video is very informative , watching you from Cape Town South Africa
Hi mate great video, very well done. I was wondering if you will ever upload a video on how to do a full remove/ clean and refit of the manifold for those of us who have found a large build up inside of it. Cheers
You're a Legend, well explained and presented, thanks you very much. Is there a video you had presented the service of Prado 2012 Diesel without dip stick, the change of transmission oils , primary and secondary fuel filters.
Thanks mate great video I’m going to watch again before I do it
Great job Anthony super informative.I watched the whole video to the end and I dare you.
Awesome video anth very informative keep up the great wok
Great piece of useful information. I had a similar experience with my Toyota Hilux 2KD engine. I cleaned purely by guess work. This video has empowered me more?
Very informative and easy to understand; thanks
cool great video just about do the whole procedure as you've described. Thanks Anthony heaps.
Great Video Anthony. Thanks for all the tips. My 150series just ticked over 360k 👍😀
I'm dared....
Great to watch all your videos mate
Thank you
Grateful to you for all the assistance you provide.
And yes I did dare you to use the impact driver
Handy Video answered a lot of my questions and I dared you.
Thank you so much, great video, very informative!
Thank you for this very informative video.
Watched video I dared u and am now going to do the job myself thankyou
Im doing this the coming weekend! Thanks for the very detailed video.
Can you comment on the fuel efficency after the cleanup? Did it improve?
Thanks for the detailed vid. I'll get into that EGR clean after my kaon plate arrives. I dared you...
Hahaha..... Catch Can....Catch Can..... Awesome Video mate, your the man....and I dare you to put a few more together.... lol..... Anthony how about doing a basic step by step Major Routine Servicing Videos.. just a thought....
Thoroughly enjoyed watching this egr clean the tips and explanations are great thank you very much. A BIT LATE BUT I DARE YOU
Awesome Anthoney. I made it to the end.
I might hit you up about an injector kit, and EGR cleaning kit soon. I have 2013 hilux 180,000kms
Cheers bro.
I watched it to the end and I did say out loud “I dare you” to which my misses reply I dare you what 🤣
Batter boom, batter bing. Love it mate. Thank you
Hi many thanks for this, just done the job on our 150 Prado something for others to consider. I was not able to get the restrictor plate in from the bottom despite much effort, ended up removing the water connection above it and doing it from there, you need to remove the hose to the cabin heater and the stand off that is bolted to the block to move the water connection out of the way, makes it a lot easier but be carful not to lose the gasket down into the skid plate below the engine, ask me how I know this! Once you have the plate on the studs re attach the water connection while the EGR cooler is loose or it is really hard to get the connection in between the timing belt cover and the cooler, tighten and then loosely attach the cooler over the plate, then proceed as per the video. I did not pull the wiring harness all the way back and worked around it, the EGR plug was very hard until I used a miniature pair of water pump pliers to release the catch and slide it off. It is the same at low power but if you push it the response is noticeably better, our EGR valve was similar to the ones in the video (100k km) so about a quarter of the inlet was blocked at that point. Obviously the coolant had to be topped up again, took it past the full mark with a litre of premix, ran the engine and turned up the heater to get that full and then had to add another half a litre. Once again many many thanks not an easy yob and messy but well worth it in my opinion.
Thanks Anthony, great video!! Unfortunately it took me bit longer then half a day, just to get the bloody clip form the common rail sensor took me about an hour, I was about to give up on it when it finally came off. It was a bitch to get there in a Prado, had to take the power steering container off, and some other stuff that I have there.
2012 LC150 1KD, Spain, EU. Inspected but clean as a whistle, well nearly, after 240k. I do use injector and DPF cleaner once a month. Thanks for uploading
SUPERBLY EXPLAINED BROTHER. Thank you.
Watched till the end very informative think I’ll have a go at my 150 now ? cheers Anthony.
I watched until the end and I dared you! Haha excellent video as usual.
Smashed it to the end. Go the impact driver to finish off. Kaon plate on order.
He makes you wanna have a go..
Great video. Where can i find your injector videos you mentioned?
Also in regards to grease on bolts, I'm not familiar with this. Which grease do you use?
Great video mate, I double dared you too for a few ugga duggas on that highly dangerous semi automatic heat seeking rattle gun, long live Makita 😉
Dude I can't believe ive only just found your channel and your an Aussie
Thanks for the video, bloody awesome.