Oh! I had a thought. There's a pair of screw terminals on the trailer modules for attaching a motor. I know they're meant for like a cement mixer drum or some other constant mechanism, but would you be willing to discuss using that circuit for running powered landing legs, instead of the Tamiya pokey-finger mechanism? Ultimately I'm interested in using it to run a screw drive on the DCM Lowboy and rebuilding the neck-to-deck coupler, so it can go from ride height, down to grounding-unpin height, then lift the locking cleat, and finally push kickstand cleats against the truck frame to lift the gooseneck clear, kind of like the Landoll single-valve single-cylinder hydraulic mechanisms.
Just watched your volume 3 of this bierer masterclass. The sounds in the preloaded folder could possibly put a boat engine sound on my Proboat sonicwake for motor sounds? That correct? Thanks Bob
You only need a USB slot. If you do need to upload you can get a card adapter like this: www.amazon.com/Reader-Adapter-Camera-Memory-Wansurs/dp/B0B9QZ4W4Y/ref=sr_1_3?crid=2VORITU88G80B&dib=eyJ2IjoiMSJ9.OP-goGzbVTBErEAb5KAgGPaK3y1KpKlwUa4P6clW3yo1aG2DiNLK9t2OgB3XmNzre-K4Kq6qWMHo9cPgMIw5azZw5WjOw_BdwOMjDy3d1-xj_ZEm0EGqA1qvfoo44Xw2K5A4hw28Jju6XHhyhX-AmctgfdnjL9TaGTYSuTWF7UDkmcxAYD35PZi6WxUkmcabtrtJg9YI8-2QwbnLxYTtsbeLWQ_2EOf4NwAn5ip-ecU.t9Skx7tpFbVhUH0l5c8UII2dlc_oJyGP9akcHz7JmwM&dib_tag=se&keywords=usb+to+sd&qid=1720283157&sprefix=usb+to+s%2Caps%2C148&sr=8-3
@@HobbyconceptsLLC Ok, I am new to the Beier system. i noticed that on the SFR-1 system the S-BUS is attached to prop #6 and on the USM it is prop channel #8. Will that make my USM have SBUS at prop #6 or is there a way to switch that prop ?
God that startup sound on the Freightliner sound set is horrible. Endless cranking. Needs to go to the shop. Hopefully in Advanced classes you'll teach how to chop those sounds down and get just a couple cranks on a cold start.
This is helpful thank you
Again, thanks for doing this!
Hi Bob, Bagger is German for Excavator
Yep, know that but still get confused when shooting videos! I will blame it on Winston's snoring :-)
@@HobbyconceptsLLCNeed to put vegetables and bread in the bucket of your biggest excavator model
Then you have a grocery bagger
Oh! I had a thought.
There's a pair of screw terminals on the trailer modules for attaching a motor. I know they're meant for like a cement mixer drum or some other constant mechanism, but would you be willing to discuss using that circuit for running powered landing legs, instead of the Tamiya pokey-finger mechanism?
Ultimately I'm interested in using it to run a screw drive on the DCM Lowboy and rebuilding the neck-to-deck coupler, so it can go from ride height, down to grounding-unpin height, then lift the locking cleat, and finally push kickstand cleats against the truck frame to lift the gooseneck clear, kind of like the Landoll single-valve single-cylinder hydraulic mechanisms.
Yes, will be doing that. Thanks!
👌
Just watched your volume 3 of this bierer masterclass. The sounds in the preloaded folder could possibly put a boat engine sound on my Proboat sonicwake for motor sounds? That correct?
Thanks Bob
Yes. I do plan on doing a boat soon just to show them in a boat setting.
@Hobbyconcepts-LLC that be great I like to see that
How can you upload from a truck, if the PC does not have card reader slots.
You only need a USB slot. If you do need to upload you can get a card adapter like this: www.amazon.com/Reader-Adapter-Camera-Memory-Wansurs/dp/B0B9QZ4W4Y/ref=sr_1_3?crid=2VORITU88G80B&dib=eyJ2IjoiMSJ9.OP-goGzbVTBErEAb5KAgGPaK3y1KpKlwUa4P6clW3yo1aG2DiNLK9t2OgB3XmNzre-K4Kq6qWMHo9cPgMIw5azZw5WjOw_BdwOMjDy3d1-xj_ZEm0EGqA1qvfoo44Xw2K5A4hw28Jju6XHhyhX-AmctgfdnjL9TaGTYSuTWF7UDkmcxAYD35PZi6WxUkmcabtrtJg9YI8-2QwbnLxYTtsbeLWQ_2EOf4NwAn5ip-ecU.t9Skx7tpFbVhUH0l5c8UII2dlc_oJyGP9akcHz7JmwM&dib_tag=se&keywords=usb+to+sd&qid=1720283157&sprefix=usb+to+s%2Caps%2C148&sr=8-3
@@HobbyconceptsLLC Thank you
Can i use the SFR-1 sound teacher system with a USM-RC-3 module?
The USM is basically just the SFR-1 without the speed control.
@@HobbyconceptsLLC Ok, I am new to the Beier system. i noticed that on the SFR-1 system the S-BUS is attached to prop #6 and on the USM it is prop channel #8. Will that make my USM have SBUS at prop #6 or is there a way to switch that prop ?
God that startup sound on the Freightliner sound set is horrible. Endless cranking. Needs to go to the shop.
Hopefully in Advanced classes you'll teach how to chop those sounds down and get just a couple cranks on a cold start.
Yep, sure will. The great part about Beier is everything can me customized the way YOU want it!