Alfa Romeo 159 2.2 jts power steering pump replacement
Vložit
- čas přidán 26. 08. 2024
- Alfa Romeo 159 2.2 jts power steering pump replacement
Замена насоса гидроусилителя руля на Alfa Romeo 159 2.2 jts.
Это видео носит развлекательный характер.
Нам понадобится:
- 1,3 литра ATF Dex 3
- эластичный ремень 3PK977EE
- плоскогубцы
- гаечный ключ 17
- биты T 30, H 5
- торцевая головка 10, 12, 13
- торцевая головка E 12
People out there always change power steering fluid every 2 years, the old fluid has metal shavings that damage the rubber seal and that over time causes the leaks.
that was a LOT of work , thank you.
I had the same issue and I’ve replaced the power steering pump, along with the alternator and air-conditioning compressor, belts and tensioner, which is basically everything on the poly-belt side. And after that, I got the same problem again lmao.
Now I ordered new powersteerimg pump again, with new reservoir and high pressure pipes connected with the pump. I wish I can see some improvements from my previous repair lol
Perhaps there is a problem in the steering rack or the high pressure hose is to blame. I hope this helps
)
Tony Shel well ironically, there isn’t any leakage of oil from the pipe nor racks either 🧐 But yeah hopefully I wish it is cuz of the hose lol
Thx for ur help😁
@@jsl9294 I read somewhere that some valves might get stuck in the tubes. Because of this, the steering system may be malfunctioning. I don't know if this is true)
@@jsl9294 Joo, I have the saaame issue, I'm researching , the noise I have is like a grinder when I first start the car, and when I move the steering it gets 10times worst. But after 10 or 15 minutes driving and the engine is hot it almost disapear. I believe is some bearing but....I don't know, maybe the teeths inside the pump.... I fear to replace the pump and don't solve the problem. Also.. is the same pump for 3.2jts or the diesels? any brand advice? (prices are very different) REGARDS, please keep in touch
@@tonyshel7672 Thank you Tony for replying , I have the same problem as I explain to Joo Sun Lee but I can't miss with the diagnostic "). I have to import it to URuguay and is expensive. is the same pump for the 3.2 jts or the diesel-'s 1.9 2.4 ? regards!
So you dont show how to get to or replace the E12 machine screw on the front of the block, just made difficult by the engine mount.
Mine buzzes when the fluid is low (I have a leak) , very sensitive to this, even a very small amount of fluid missing and it buzzes like a donky. With fluid to the max no problems or noise.
Yes, the Alpha is fluid level sensitive like no other machine.
Where did you order your bleeder screw?
Commonly fail ?
Hi just wondering many hours does it take to do the job? Does one need to drain the system? A mechanic told me there was a recall for a fault of this system and therefore you have to also replace the hydraulic fluid. I that correct?
It took 1.5-2 hours to remove / install the pump. It is better to drain the liquid to the maximum so as not to stain the engine compartment.
Any clues on how to tension the belt? I haven't removed my pump yet but the official workshop manual makes it look very complicated.
I forged the belt with a screwdriver, and my partner turned the wheel to turn the flywheel. The strap stretches a little, so don't be afraid to tear it.
@@tonyshel7672 Great, thank you! I removed the pump today so I will try this later. Thank you for the video
My pump doesn’t make any noise, but sometimes the power steering doesn’t work at low revs / on idle. Really tuff when parking. Could it be the pump anyway, or more likely something else?
Most likely the pump will break soon. Better to fix it, in my country it's not expensive, I don't know how much it will cost in your country)
@@tonyshel7672 where are you from brother?