How To Fix Ps3 Overheating Problem? PS3 overheats and turning off? overheating after thermal paste?
Vložit
- čas přidán 21. 07. 2021
- How To Fix Ps3 Overheating Problem? PlayStation overheating after thermal paste?
So, you just cleaned your PS3, replaced the thermal paste and it didn't work? Here is the solution for you. In this video, you will see how to remove the metal plates from RSX and CELL chips ( delid ) and replace the thermal paste to bring your ps3 back to life.
So, if your ps3 shuts off while you are playing, watch this video.
IHS removal PS3 FAT
PS3 overheating and turning off
Noisy fan - Věda a technologie
i like how you never showed it running again. how do we know if this fixed the problem?
I wish there was an after video of the noise after the thermal paste replacement
I love the plane you added while the ps3 was making that noise. That was so funny. 😂😂
HOW DO YOU SEAL IT BACK?ARE YOU GOING TO PUT THERMAL PASTE AROUND IT AS WELL?
Thank You! You saved my PS3!
Thanks for the video. Thinking of doing a restoration on my old PS3. It literally sounds like a jet engine but I am going to replace the thermal paste, raise the console slightly, install an SDD and a new fan and see if that helps. What tools would you recommend for disassemble etc?
For dissasembly, you will need a prying tool of some sort, a T8 screwdriver, a size 1 and size 00 Phillips head screwdriver, some kind of cleaning brush to get dust out of the crevices, and about 90 to 120 minutes of patience. I just did mine yesterday, cecha01 60gb, and it is WAY quieter. The improvement is quite major compared to what it sounded like before. Honestly, you probably don't need the fan. The ssd doesn't make a big difference on ps3 either.
Keep doing what you do mark .
Keep making contents
Keep growing up
Thanksssss dude
Thanks for the video Mark!
I recently bought a 60gb PS3 and is loud like a plane but i think you just resolved my problem!
I have a question though, the procedure you are making on the cpu can also be done on the RSX plate too?
Thanks again for the video :D
Yes, exactly.🙂
"If you feel resistance when pushing, you should stop" - welcome to my Ted talk, today is "how to pick up girls, 101" :D
Thanks for the vid man, I found an old ps3 for $25 with overheating issue and I'll buy it.
i got the same problem how can i deal with it help, looking forwad to your help
great video, made me laugh
Keep that on 👍🏼
Thanks dude
To make cooling performance even better, use Thermal Grizzly Conductonaut liquid metal thermal paste for EXTRA cooling and less thermal throttling!
Just started with restoration old PS3(cechh03) Cleaned dust with water from non electric components. Good thing that it’s very modular, every piece can be easily tear apart.
I Broken motherboard, don’t use nothing else but really only blades hah i tried with technical knife, its to hard.
Should I use B6000 glue to reattach the heatsink?
Was the result shown in another video?
Funny thing I just tried this play too flimsy thermal paste to dried eventually got the plate off had to use some heat but wound up tearing up some of the green stuff on the box
What kind of glue is this? Is silicon?
Hi buddie what do you use to stick down the metal plate when you replaced the thermal paste?. Thanks again.
Hello, I didn’t use anything, just applied thermal paste.
@@ReMARKCHANNEL ok thanks I was just a bit worried that if I didn't use anything it would move about after reinstalling. Thanks for you help buddie👍.
Thank you
Hey the photo from 1:50 is my delid photo from reddit haha, small world
Yep, took it to show an example, nice pic by the way😂
thanks!
My ps 3 not even load just ove heates do i need a new fan
But what if i cant replace termal pad
Mi PS3 super slim was acting as if it has a broken WiFi module which was not the case because when i've upgraded (via pendrive) the system software to 4.89 voila! wireless internet conection was back... but and that's a big but... my perfectly functional and fully charged original controllers are not syncing (i'm using orignal USB cable)... any suggestions? i've already tried reseting the controllers with a clip.
Hello, controller uses Bluetooth as far as I know, so this might be the issue.
I have a super slim model and when I start playing games the fan starts to bee so lawed what should i do ??
First of all, take it apart and clean it. Then, apply a new thermal paste. It has to solve your problem.
Can i do the same with rsx. Did u use thermal paste again between cpu and square metal plate (not radiator)?
Yep, there is gotta be the paste.
@@ReMARKCHANNEL what about the edges, originally it was a some kind of silicone, how can i glue it.
@@peceq83 i didn’t glue it
Only my rsx overheats. My cpu is fine after repaste of ihs
I saw something on CZcams shorts about this video and is it true that i will kill my PS3 fat if I take that piece off? Or was it just the PS3 silm and super silms, I want to do this but now I need to know for sure.
Hi it depends on your skills. Use a fishing line to reduce the chance of breaking it
What type of glue should I use to read attathe CPU thanks for the video
Crystal? U mean silicone?
Still overheating and fan noises
In Slim model it is essential to change the internal paste 😅
Hey RE:Mark ai just changed the thermal paste but it still shuts down after ai play it what do ai still need to do to make it work am super confused.
Hello, I guess you have the same problem as I had. You need to scalp those metal plates from gpu and cpu and replace the paste there.
I want to confirm from people in the comments section if it displays before the PS3 turns off
How did you attach the plate again?
I just cleaned it and put it back in place. I didn't use any glue.
@@ReMARKCHANNELdo they fit properly
@@RehanKhan-il7dl well, it does it’s job)
i have my cousins ps3 he didn't want i wanna play some games i bought for it but it keeps freezing it doesn't give me any overheating issue just freezes in the menu i replaced the hard drive and nothing
Hello! If you replaced the hard drive in your ps3 and it still freezes the same way it did before the replacement, I'm afraid there are problems with your hardware - RAM, GPU or CPU...
@@ReMARKCHANNEL yeah same i dont know what it is
it dosent afect to much the PS3 Fat is generall a loud console. Test it with MW3 iz Extream no mather wich Thermal Paste or his replace
@@bernardbockwurst No wonder the first edition PS4 pro is a jet engine 😁 but on amzone you find a set with including Nidec fan it reduce noise 40% the stock Delta is a mess with high pich noise
Why in all the videos of removing the IHS, they also remove the thermal paste?
Is ps3 2500a hot model and its cpu is like fat cpu or not? I recently bought a ps3 slim model 2500, the temperature of the console reaches 77 degrees with a fan speed of 40, but I have had it for about a month and sometimes I played with it for up to 10 hours without any problems. Will there be any problems later? And the last question, how are the ps3 2500a? Like Fat, they don't have a yellow light problem? Sorry for the many questions, please help me by answering them
More detailed information: when the console has not been turned on for at least 5 hours and when you turn it on, the temperature is sometimes 34 and sometimes 40 degrees with a fan speed of 20 and in 5 minutes the temperature reaches 60 to 67 (cpu 67 rsx 64) and If you stay in the menu like this, the temperature reaches 72 and sometimes 75, and when you enter the game and play the game "Battlefield 4", the temperature reaches 76-77 and the fan 40, when the fan is 40, reduce the temperature from 77 to 72-73 gives and never goes higher
Hello, check the paste. If it doesn’t work, must be the same problem as I showed on the video. No, 2500a also shows YLOD.
@@ReMARKCHANNEL my slim stays kool @ 58c idle cpu and 56c rsx, no delidded required
@@joeydelmarsjr.646how?
I have this same ps3 but my ps3 power comes on when you plus it and then when you press the power button it turn green and then go off immediately
I need help please 🙏🏼🙏🏼
ru.ifixit.com/Guide/Fixing+Playstation+3+Green+Light+of+Death+(GLOD)/5163
Hello, man I would start by checking the power supply.
Hi, can you help me, please ?
I have a PS3 Slim Mod. CECH2504A which is equipped with:
- CPU CXD2992GB
- RSX CXD5300A1GB
Firmware: 4.89 CEX
Software mod.:
- HEN 3.1.1
- webMAN MOD [4.82] v1.47.09
After a couple of minutes that the console is turned on:
CPU: 65°C - RSX: 67°C - FAN: 25%
Then the fan speeds up and after a time that varies each time between 5/10' and 30':
CPU: 81°C - RSX: 44°C - FAN: 69%
Sometimes it stays like this and I can play, other times the CPU increases to 83/84°C, then the message to turn off the console appears and if I don't do it, a double beep sounds and it turns off on its own.
Well now my questions:
1) Do you recommend doing the delid?
2) I only tried for a few moments to do as you say in your video, using a cutter blade, but I think it is too thick; Should I use a razor blade then?
3) Isn't it necessary to use a heat gun to soften the surroundings?
4) I purchased the MX-4 thermal paste, can I also use it inside the processors?
5) To reassemble the two "cover" parts of the two processors, what do you use? Silicone, glue, or what else?
Thank you for your patience, if you have read all this, and I hope you want to answer me !
bye
Steve.
Hello. I used razor blade but please be very careful and patient! Second, no force! Work on edges, don’t go deeper. Mx4 will work. Heat will help you to make the glue softer and a little bit easier to cut. I didn’t apply any glue, but you can try something thermal resistant.
One more time. The razor blade must be horizontal 0*. It’s very easy to scratch the surface!
Sorry, did you try to replace the thermal paste? Maybe it will work
thank you for your answers !
well, i already replaced the thermal paste but my old FAT after this passage is turned on once time, fan cooler speed up max level, then turned off and now Rel Light is permanent and i can't turn it on no more (if i press Eject button i feel 3 beep and . . . nothing.
In my PS£ slim i already replaced the thermal paste, but the problem it stays again.
now i'm thinking to make reballing of BGA CPU by a collegue in electronics company corporation where I am employed, I learned that we have reballing machinery and a technician specialized in BGA.
Stay tuned 'cause in January, once the reballing has been carried out, I will be able to say if everything is fine (I hope).
Thanks again and happy holidays ahead! @@ReMARKCHANNEL
What do you use to put it back on
just thermal paste
I have a problem to my ps3 bro when I play God of War Ascension then 20 minutes my ps3 automatically shutdown and there's a notification said that the system has become hot please turn it off and wait for it to cool down something like that then 3 beep then shutdown with blinking red light I think this is not a YLOD coz I can turn on my ps3 fat 80gb model but unlike the other ps3 mine is more quieter than a hair blower please help me resolve my problem any advice will appreciated thank you
hello, check thermal paste under that metal plate, i guess this is the reason
@@ReMARKCHANNEL It's already open before do you think it can reopen easily
@@ultimatesasuke7807 yes, just don't make quick moves and be carefull.
@@ReMARKCHANNEL Thank you very much bro you earn another sub
So, I have a PS3 slim and it's HFW. So like in 5 mins it's already overheating. Does anyone know why?
Hello, have you tried what I showed in the video?
@@ReMARKCHANNEL I'm gonna replace the thermal paste soon. I'll tell you if it works.
Hello i have a ps3 slim and my rsx is always a bit hotter, for 2h of gta4 i get 64C cell and 67~rsx 26%~ fan is that ok ?
That’s fine.
This great 😂 What is your ps3 model number?
Op video full support from Pakistan
Just was passing a Pakistanian embassy yesterday 🙂
@@ReMARKCHANNEL so good bro 🙂
Welcome to Sony Airlines. Welcome aboard our booing-AirStation3. Please fasten your seatbelts
Here in 2024
Hey man it's almost summer time and my ps3 started giving me a lot of overheat warnings although it never turns off and goes up to 85C do i need to repair it ? (I have a jailbroken ps3)
Hello, cleaning and replacing thermal paste may solve your problem. If it’s a fat ps3 like mine, this video might help
@@ReMARKCHANNEL is the original ps3 the fat ps3? i havent used my hb ps3 in a while so i forgot some stuff
I thought I just had to place a fan next to it then we good💀
Got a backwards compatible ps3 while playing for about an hour or two it was a bit loud but not jet engine loud while I was playing scarface game it randomly shut off
Is mx-4 will do good job?
Have never tried mx4 thermal paste. I always use gd900 ( cheap thermal paste from China but does a great job). I heard that mx4 is one of the best. Gotta be good in your case anyway
@@ReMARKCHANNEL but which tool i use open the cpu?
@@xxechobgxx3797 razor blade
@@ReMARKCHANNEL ok thx 😄
@@ReMARKCHANNEL but i can do it with little sharp knife
So I opened and disassembled my ps3 and put toothpaste as a replacement for the thermal paste, unsurprisingly whole thing shut down right in front of my dumbass. Thats my problem but thank god I have a backup ps3 and RPCS3 on my pc if that ever happened.
Nice this good video
Thanks man
@@ReMARKCHANNEL you're welcome bro
@@ReMARKCHANNEL you like this my PSP CZcams channel is video
@@LEECHINLEONG0705 like-minded people🙂
@@ReMARKCHANNEL yeah I gameplay PSP Games GTA God Of War Mega man Tekken 6
I applied thermal paste and still my console still make this noise
there is a software hack mod you can add, that lets you edit when the fans turn on and how much, its the best for this ps3 fats.
howbis it called?@@badtuber1654
Any chance I can send you my ps3 and have you fix mine and I pay you?
I'm afraid it will be crazy expensive. Check how much money it will cost to deliver it to Beijing.
Still no working
Pardon me, what exactly is not working? Your console is still overheating after you did what I showed in the video?
Holy fk, airplanes are silent than this
Yeah... Don't do this. Trying cutting into in for like 2 hours and couldn't do it. I gave up and plugged it up and now it's dead. 😢
Great tutorial! ...but please be really careful with that razor! you pushing it with force in the direction of your hand/arm that is holding the mothermoard made me cringe real hard!
Don't want people to end up in the hospital
Why did they make PS3's to where they would overheat to begin with? Is it just to make money? Because I never knew of any system before PS3 to overheat. It's also absurd to pay all this money on a console where you have to replace a paste. That's insane. If we are paying hundreds of dollars on a console, replacing a paste shouldn't even be a thing.
Oh god, that's an awful design, no wonder these consols last only a few years, why add more failure points sony, just have a cpu, one thermal paste contact, fan on top of cpu, done...
Thank you
Always welcome