This is 100% the best film installation video on CZcams! Every other video is some amateur struggling with zero tips. If I wanted struggles I would just try to do it without doing research. Your is nothing but tips and is so helpful!!!
I watched this video a few times before installing my lamp liner PPF just to get an idea of how to. And it was breeze to install thanks to this video and the information provided.
I’m with ya. But I find the one little imperfection I always end up with is just for me to remind me I didn’t pay someone to do the job ;) and I’m not perfect. I’m ok with that! Mine had two small bubbles that would not go away. I syringed them out but still can see them. Tried hot water to cure ppf nope.. so I just live with it. It’s not in the middle and no one will see unless I point it out to them. Great video thanks
Thank you, sir. I used these tips installing a pre-cut xpel ultimate kit on my car. It was my second time ever and the film wasn't cheap but great quality and very forgiving when installing. I tried some bulk 3M ppf in the past and it was a nightmare to work with so I just gave up.
Nice subie man I just did my 23 wrx headlights and fogs. I actually put blue painters tape on the headlight and used a sharpie to outline the light then pulled it off cut out the shape then stuck it to cardboard paper and cut that out then onto the film. It was pretty quick. I’ve never done ppf before but it came out pretty good. Could you have used heat on the stubborn corners or fingers as you said ?
Question: In this video you "tacked" down the inside corner of the headlight to begin, but you did not use any "tacking solution". So, will the film adhesive work/tack/stick using only the "slip solution"? Or do I need to apply "tacking solution" to the entire inside portion of the film? I'm going to replace some PPF on my truck, and this is the first time I've ever applied it, so I'd like to get it right the first time. Thanks for the helpful video and reply.
You do not need to use tack solution to make the ppf stick. The slip solution will tack it but not right away. You can also use hot water as a tack solution. If you need to relax the film a steamer works great. Hopefully this was helpful and best of luck on the install 👍
Good to know! I've watched several PPF install videos and no one has mentioned this little detail. I appreciate the help. I've been browsing and watching a few of your other detailing videos as well. Great job. Keep up the excellent work and best of luck in the future.
I do not have a video on that vehicle but I can give you the measurements of the pre-cut if want. Once I get one in the shop I will for sure put the video out for you.
Yes, tack solution is uses to lock down so you can pull the material to relieve fingers. Check out this install which has a better understanding. czcams.com/video/9BUj9iMCojE/video.html
I had some PPF put on the headlights of my new Porsche 911.. do you know if it will harm the headlights if I have them removed and replaced? Does it do damage to the headlight lease or is there a coating I should be worried about?
What year is your 911. On my last 911 I did the dealership had to remove the ppf off the entire car to certified the vehicle. The headlights have a type of coating on them. The headlight did have some areas where they were damaged. This could be from just ripping them off and not using a steamer to help relax the film when removing.
This film is 10mil solargar hydro 10yr warranty. I now used suntek ultra paint protection film which 7mil also has a 10yr warranty both film are awesome!
it would make more sense for you to do this process, but end on the bottom not the top. As it is, it’s easy for the liquid to get into the finger, but gravity works for you in the opposite direction.
Sometimes I do the opposite way. The key is to lock a point and pull the material to relax the fingers so they are gone before you squeegee out the slip solution .
Hey Chris I will try and get one of these in for you. I do have the pre-cut film if you would like to order one after I make the video for you. Best thing to do is tack down a corner and then pull the ppf to the opposite corner and tack that in place. Then squeegee the liquid out. If you have fingers try some tack solution to push them out or steam to help relax film.
Thanks. I'm using a gcc plotter 40in jaguar vlx. For all my templates I used SolarGard and SunTek software. If you need a pre-cut template head over to my website m2mdetail.com 👍
@@m2mdetail781 much appreciated on the info I run a headlight restoration LLC and noticing that the pre cuts make the job a hell of a lot easier you think a 40" is good for what ill need kit for headlights I'm thinking in purchasing one with the software
@@stefangonzalez2285 if you are just doing headlights I would look at 24in plotter that will save you a lot of money then buying the 40in. I have 40in because I do a lot of window tinting and full car ppf.
I have the simplest headlights out there (several Lincoln Town Cars) In roll form this stuff does not behave as shown! Fingers that are smoothed out pop back up in a few minutes. The film will only conforms to one curve. It does not stretch or shrink to fit. I THINK IT ONLY WORKS WITH THESE PRECUTS AND LOTS OF PRACTICE. It looks so easy, so I just wasted quite a bit of money that is now wet, stuck to itself and in the trash. Any advice is welcome so I can waste more money. Who knows, I may figure it out yet.
Hey yes practice does make it a lot easier. When you get those fingers spray hot water in them and knock them down. Also when installing the film lock down one side a stretch the material across so there are no fingers. This will stop the fingers from happening in the 1st place hope this helps and good luck. If you want to try some pre-cuts I sell them on the website. m2mdetail.com
I havent used clar bar on headlights. If you have to do a headlights restoration do that before applying PPF. You want your headlights to be in the best shape before applying.
@@m2mdetail781 hey, thank you so much!!! I really appreciate you responding so quick!! Thank you for the video!! I’m gonna take a shot at putting PPF on my Model 3’s headlights tomorrow!! Wish me luck!!!
Hey thanks for the inquiry and yes I do here is a link for them. I do not have the pre-cut for the fog lights though. I also added door cups, front bumper, hood and fenders templates as well. m2mdetail.com/store/ols/products/2020-toyota-highlander-door-cups-202-tyt-hgh-dr1
You can buy from our website or eBay. Just send us a message if you don't see your vehicle and we will get it listed for you. m2mdetail.com/ www.ebay.com/sch/i.html?sid=marc16sti&isRefine=true&_pgn=1
Already getting lost, when you seem to first , put on ppf, solution? Is not the same- as Slip solution ?" We're gonna PPF this" - Cause I only saw you mix 2 things , Slip & Tack. NOW Im seeing 3 diif Bottles, Black or purpe top, Green tops, and suddenly, white top solution... Im using 3M precuts 2015 accord coupe. For SUN, not paint ? protection, not damage yet . Please use same terms. For 1st timer women,maybe men like me? Written instructions, I got lost- when they mentioned alcohol. Hope you clear this up, for me
So just watched the video twice to try understand where you are coming from.. I only saw two bottles if I used three it was probably another slip solution bottle I have a bunch of them. Here is another video that should help you out. We also only use hot water as tack now no alcohol. Best of luck 👍 czcams.com/video/9BUj9iMCojE/video.html czcams.com/video/CGoj4vEmmjU/video.html Hopefully these help you out.
@@hubertfuent863 if you watch my other video on how to remove clear bra it shows you. You could use a heat gun but it is better to use a steamer. The heat gun can be too hot and the clear bra will not want to peel off.
@@hubertfuent863 I would do it for sure. If you are interested I sell pre-cut kits on my website and a install kit. m2mdetail.com Contact us on the website and I will send you over the template so you can see what they look like for your vehicle. You can also text the shop number found on the website and I can send you pictures of PPF kits. 👍
“Simple process” I tried for 4 hours on 22 wrx headlight. This is impossible! I couldn’t do it. Got frustrated and gave up. There goes $150 done the drain for a front end kit headlights and bumper. This is not DIY job. Unfortunately I live is shity over priced, very expensive Canada and PPF places want $4000 CDN just for front end bumper and headlights! Get bent! Guess my car will get riddle with rock chips. PPF is not DIY job. It’s expertly hard. I followed this video to a T to.
This is 100% the best film installation video on CZcams! Every other video is some amateur struggling with zero tips. If I wanted struggles I would just try to do it without doing research. Your is nothing but tips and is so helpful!!!
Definitely the best conducted instruction on CZcams in this topic.
Thanks
I watched this video a few times before installing my lamp liner PPF just to get an idea of how to. And it was breeze to install thanks to this video and the information provided.
HUMAS SHOULD LISTEN TO THIG GUY. WELL DONE. VERY INFORMATIVE
You make it look so easy. I always get folds and bubbles.
I’m with ya. But I find the one little imperfection I always end up with is just for me to remind me I didn’t pay someone to do the job ;) and I’m not perfect. I’m ok with that! Mine had two small bubbles that would not go away. I syringed them out but still can see them. Tried hot water to cure ppf nope.. so I just live with it. It’s not in the middle and no one will see unless I point it out to them. Great video thanks
That is the best demonstration video I have yet seen. Thank you. 🙏🏻
Great work! It will take me an hour to do that. Thanks for reminding us to be patient with getting rid of those fingers.
Thank you. 👍
excellent tack and stretch technique. very professional effort.
Thank you, sir. I used these tips installing a pre-cut xpel ultimate kit on my car. It was my second time ever and the film wasn't cheap but great quality and very forgiving when installing. I tried some bulk 3M ppf in the past and it was a nightmare to work with so I just gave up.
Thank you. Great movie and very professional given details.
Good clip, youmake it look easier than it is.
Nice video bro, good walk through.
great tip on the tack fluid so many videos ive watched on this no one knows that! great video
Thank you.
He never even used the tack solution that I seen.
@@Thomas998822 Watch it once more, Sherlock. He did use the tack solution.
Excellent video, man.
Great video!
Very useful. Thank you
Great tips! Thanks!
Nice subie man I just did my 23 wrx headlights and fogs. I actually put blue painters tape on the headlight and used a sharpie to outline the light then pulled it off cut out the shape then stuck it to cardboard paper and cut that out then onto the film. It was pretty quick. I’ve never done ppf before but it came out pretty good. Could you have used heat on the stubborn corners or fingers as you said ?
Thank you, very nice.
Is tack solution necessary if you managed to squeeze all the soap solution out?
Question: In this video you "tacked" down the inside corner of the headlight to begin, but you did not use any "tacking solution". So, will the film adhesive work/tack/stick using only the "slip solution"? Or do I need to apply "tacking solution" to the entire inside portion of the film? I'm going to replace some PPF on my truck, and this is the first time I've ever applied it, so I'd like to get it right the first time. Thanks for the helpful video and reply.
You do not need to use tack solution to make the ppf stick. The slip solution will tack it but not right away. You can also use hot water as a tack solution. If you need to relax the film a steamer works great. Hopefully this was helpful and best of luck on the install 👍
Good to know! I've watched several PPF install videos and no one has mentioned this little detail. I appreciate the help. I've been browsing and watching a few of your other detailing videos as well. Great job. Keep up the excellent work and best of luck in the future.
You could use a hair dryer to get the bubbles out and help it to stick to the headlight
Thanks for the info 👍
Do you have a video installing on a 2018 to 21 Subaru Crosstrek? Curious on how well it covers the top of the headlight.
I do not have a video on that vehicle but I can give you the measurements of the pre-cut if want. Once I get one in the shop I will for sure put the video out for you.
Nice Subaru
Small world i'm pretty sure i own it now minus the front splitter and stickers
Hello do you use pure water? me it doesn't stick on the edges... I heated it but no luck
Does this stop the lights from yellowing?
Hello, useful video
Thanks
Can you explain which purpose using the tack solution?
Yes, tack solution is uses to lock down so you can pull the material to relieve fingers. Check out this install which has a better understanding.
czcams.com/video/9BUj9iMCojE/video.html
@@m2mdetail781 Thanks a lot❤❤
I had some PPF put on the headlights of my new Porsche 911.. do you know if it will harm the headlights if I have them removed and replaced? Does it do damage to the headlight lease or is there a coating I should be worried about?
What year is your 911. On my last 911 I did the dealership had to remove the ppf off the entire car to certified the vehicle. The headlights have a type of coating on them. The headlight did have some areas where they were damaged. This could be from just ripping them off and not using a steamer to help relax the film when removing.
@@m2mdetail781 here is my car, a 2020 992, we used SunTek... czcams.com/video/Q6L3bz_H1GQ/video.html
@@Sams911 looks awesome just saw this sorry about the late reply
Can you heat the film to make it conform to round head lights?
How many millimeter is the film, I only want to do this once and have it last/ Great video
This film is 10mil solargar hydro 10yr warranty. I now used suntek ultra paint protection film which 7mil also has a 10yr warranty both film are awesome!
it would make more sense for you to do this process, but end on the bottom not the top. As it is, it’s easy for the liquid to get into the finger, but gravity works for you in the opposite direction.
It's prolly cuz he doesn't want to get rid of the liquid but what's to squeeze it out so bottom to top would keep it there until the end
Do you use the same technic for all headlights? Tack inner corner and advance? I’m having trouble with an Elantra 2013
Sometimes I do the opposite way. The key is to lock a point and pull the material to relax the fingers so they are gone before you squeegee out the slip solution .
M2MDETAIL thank you 🙏🏻
Can you post a video for 2016 Toyota Sienna’s headlights? I didn’t have a pre-cut film, and I was struggling with putting on a ppf last night
Hey Chris I will try and get one of these in for you. I do have the pre-cut film if you would like to order one after I make the video for you. Best thing to do is tack down a corner and then pull the ppf to the opposite corner and tack that in place. Then squeegee the liquid out. If you have fingers try some tack solution to push them out or steam to help relax film.
M2MDETAIL yes, I would love to watch your video first , thank you so much
quick question how do I get that pre cut ppf machine? also what website did you use? awesome video by the way!!
Thanks. I'm using a gcc plotter 40in jaguar vlx. For all my templates I used SolarGard and SunTek software. If you need a pre-cut template head over to my website m2mdetail.com 👍
@@m2mdetail781 much appreciated on the info I run a headlight restoration LLC and noticing that the pre cuts make the job a hell of a lot easier you think a 40" is good for what ill need kit for headlights I'm thinking in purchasing one with the software
@@stefangonzalez2285 if you are just doing headlights I would look at 24in plotter that will save you a lot of money then buying the 40in. I have 40in because I do a lot of window tinting and full car ppf.
M2MDETAIL PERFECT 👌 THANKS FOR THE HELP AND PROFESSIONAL ADVICE IM ON IT!!
What website did you use to cut the template
Which website did you use to get the premade template to cut?
At that time I was using computer cut. Now I used CORE for my software which is suntek software.
I have the simplest headlights out there (several Lincoln Town Cars) In roll form this stuff does not behave as shown! Fingers that are smoothed out pop back up in a few minutes. The film will only conforms to one curve. It does not stretch or shrink to fit. I THINK IT ONLY WORKS WITH THESE PRECUTS AND LOTS OF PRACTICE. It looks so easy, so I just wasted quite a bit of money that is now wet, stuck to itself and in the trash. Any advice is welcome so I can waste more money. Who knows, I may figure it out yet.
Hey yes practice does make it a lot easier. When you get those fingers spray hot water in them and knock them down. Also when installing the film lock down one side a stretch the material across so there are no fingers. This will stop the fingers from happening in the 1st place hope this helps and good luck. If you want to try some pre-cuts I sell them on the website.
m2mdetail.com
@@m2mdetail781 Thank you for your kind advice. I will try again using your tips. If I am still unable to get it right, I'll try the precuts.
so you don't need to clay bar the headlight before applying?
I havent used clar bar on headlights. If you have to do a headlights restoration do that before applying PPF. You want your headlights to be in the best shape before applying.
Is there a website where we can buy pre-made templates without having to buy everything needed to cut it?
Yes m2mdetail.com and you will find us on ebay also
@@m2mdetail781 still have the site? I’d be interested
@@tristancefail yes m2mdetail.com. just send us what pre-cut your looking for along with the year, make, model and trim of the vehicle. 👍
@@m2mdetail781 sent an email, thank you!!
@@tristancefail 👍 you will get an email back shortly. Thank you
hi I am wondering how you get your film cutting machine?
I would go through suntek to buy one.
What’s that white thing you used at the end of the video to “tac” down the edges?
Mac tac. They help soak up the slip solution
@@m2mdetail781 oh. Ok cool. Thank you!! Can you purchase that online?
@@jazminesanchez7449 yes here is a link
bereeloutdoors.com/gdi-tools-mactac-felt-squeegee-gt1000/
@@m2mdetail781 hey, thank you so much!!! I really appreciate you responding so quick!! Thank you for the video!! I’m gonna take a shot at putting PPF on my Model 3’s headlights tomorrow!! Wish me luck!!!
@@jazminesanchez7449 good luck brother! I also sell the pre-cut kit for your center console if your ever in the market for that 👍
What are the benefits of using the Mac tac?
To absorbed the solution
Is there a PFF for a 2014 Honda Accord headlight sedan?
Yes there is contact me on the website and i can get these made. m2mdetail.com
3rd kit i ordered i dont feel like attempting it again 😒
can you ship me templates for 2021 tacoma 3rd pro? and fog lights? Do you have a link to order these?
Hey thanks for the inquiry and yes I do here is a link for them. I do not have the pre-cut for the fog lights though. I also added door cups, front bumper, hood and fenders templates as well.
m2mdetail.com/store/ols/products/2020-toyota-highlander-door-cups-202-tyt-hgh-dr1
@@m2mdetail781 bro I live right down th street from your shop.. do you have templates for a 2020 ram 1500 bighorn
@@NoSpillsChills Nice! Yes I do brother. Give me an email at m2mdetailing@gmail.com and I'll send them over to you in the morning 👍
What's the advantages of using pre-cut, tnx.
Time. They both have pros and cons. All depends on what you are PPF. We use bulk and pre- cuts
Can you do this without a template cut?
Yes. Most of the time it is easier to just hand cut them.
What is that water and dish soap
1oz baby shampoo and 32oz water
How long dose the film last
Film comes with a 10yr warranty
can youpre cut skoda rapid 2013 headlight?
No
Is there a PPF for 2007 tacoma headlight?
I will check for you.
Just checked my system and no there is not any template for headlights. I have your front bumper and partial hood and fenders
Where can i get that ppf ?
You can buy from our website or eBay. Just send us a message if you don't see your vehicle and we will get it listed for you.
m2mdetail.com/
www.ebay.com/sch/i.html?sid=marc16sti&isRefine=true&_pgn=1
@@m2mdetail781 u dont sell by foot ?? Dont want pre cuts
@@christopherpinto884 we can sell by foot what size are you looking for and ill give you a quote.
@@m2mdetail781 12 inc x 48 inc and 6 feet x 8 feet
@@christopherpinto884 okay 12 by 48 would be $40 free shipping.
We only carry 60in roll (5ft).
5ft by 8ft would be $230 free shipping.
Already getting lost, when you seem to first , put on ppf, solution? Is not the same- as Slip solution ?" We're gonna PPF this" - Cause I only saw you mix 2 things , Slip & Tack. NOW Im seeing 3 diif Bottles, Black or purpe top, Green tops, and suddenly, white top solution... Im using 3M precuts 2015 accord coupe. For SUN, not paint ? protection, not damage yet . Please use same terms. For 1st timer women,maybe men like me? Written instructions, I got lost- when they mentioned alcohol. Hope you clear this up, for me
So just watched the video twice to try understand where you are coming from.. I only saw two bottles if I used three it was probably another slip solution bottle I have a bunch of them. Here is another video that should help you out. We also only use hot water as tack now no alcohol. Best of luck 👍
czcams.com/video/9BUj9iMCojE/video.html
czcams.com/video/CGoj4vEmmjU/video.html
Hopefully these help you out.
Does this come off say after 1 or 2 years v
You can remove it at anytime. Comes with an 8 year warranty.
Marc Maloof that’s awesome thanks for replying. Now does it just peel off or do apply heat to peak off ?
@@hubertfuent863 if you watch my other video on how to remove clear bra it shows you. You could use a heat gun but it is better to use a steamer. The heat gun can be too hot and the clear bra will not want to peel off.
M2MDETAIL gotcha gotcha
This is the first time I actually thought of protecting my headlights-since I bought new updated ones-
@@hubertfuent863 I would do it for sure. If you are interested I sell pre-cut kits on my website and a install kit.
m2mdetail.com
Contact us on the website and I will send you over the template so you can see what they look like for your vehicle. You can also text the shop number found on the website and I can send you pictures of PPF kits. 👍
Bro do you have PPF for the 2019 Toyota Hilux 4x2 headlight and tailight?
I will check for you man when I get to work today.👍
Hey brother at this time my software does not have any templates for your vehicle. Once they update you vehicle I will reach out to you.
M2MDETAIL what software do you use?
@@docotis420666 he uses SUNTEK software
“Simple process” I tried for 4 hours on 22 wrx headlight. This is impossible! I couldn’t do it. Got frustrated and gave up. There goes $150 done the drain for a front end kit headlights and bumper. This is not DIY job. Unfortunately I live is shity over priced, very expensive Canada and PPF places want $4000 CDN just for front end bumper and headlights! Get bent!
Guess my car will get riddle with rock chips. PPF is not DIY job. It’s expertly hard. I followed this video to a T to.