Great video!!! I have noticed that not many people show how to configure the router or the Layer 3 Switch to be a DHCP Server. The only thing that video lacked was showing how to make the L3 Switch to also be the DHC Server of the network
thank you for this. The CCNA volumes from cisco press do a bad job on this topic. I know this does not directly relate to the video, but I can't use the web browser in the simulation or ping the routers from the PCs. How would you set the PCS and routers up to get to the internet using a web browser?
Is it necessary to create additional "interface vlan (10, 20 or 30)" on each L2 switch? Couldn't recall this from CCNA course. And how did you set up trunk port on MLS switch, there was no configuration, but nevertheless it shows that port is operating in trunk mode, was it done automatically after creating vlan interfaces?
Actually there is no need to do that on Layer 2 switches (accept for Vlan for managing the switch itself, in this video he made it interface Vlan99). SVIs are created on Layer 3 switch for inter Vlan routing
@@theFilipinofoodie Vlan99 is for management of the switch itself, it doesn't have to be 99 it can be any Vlan number, but you should give an ip address to it. Native Vlan will be untagged on trunk port, so that devices can use it.
i have question, is it really necessary to enable interface vlan on the access switch that is not in use? Here the management is VLAN 99 and it should be the only activated interface vlan on the remote switches.
Hey thanks for the videos its pretty much helping, i have a probleme. I have this network lan1(with different vlan) => switch => router => router => switch => lan2, i configure an ospf routage on routers but the ping does not work between the same vlan on different lan Can someone help??
Question is why enabled int vlan 10,20,30 on all the access switches? It could be just vlan 10,20,30 and assigned edge devices but why int vlan 10,20,30 on access switches when we don't assign then ips,????? Any reasons for it? Int vlan 10,20,30 should be defined on layer3 switch but why on access?????
You did a great job explaining this procedure. Something I have been trying to figure out for a year or so. Thank You!
Thank Salah. Not only video is great but supporting documents are very good. Fluency is showing your expertise.
Kashif Mohsin Thank you Kashif.
Great video!!!
I have noticed that not many people show how to configure the router or the Layer 3 Switch to be a DHCP Server.
The only thing that video lacked was showing how to make the L3 Switch to also be the DHC Server of the network
Thanks for the great work
very well explained. Great video!🙏👏🤜
Thank you sir. Helped alot!
Excellent ... well done...
Thanks. Much appreciated
thank you so much, good video
Great video, keep up
great work
good video ! Thanks.
nice sharing
Très bn cours
thank you for this. The CCNA volumes from cisco press do a bad job on this topic. I know this does not directly relate to the video, but I can't use the web browser in the simulation or ping the routers from the PCs. How would you set the PCS and routers up to get to the internet using a web browser?
same
Is it necessary to create additional "interface vlan (10, 20 or 30)" on each L2 switch? Couldn't recall this from CCNA course. And how did you set up trunk port on MLS switch, there was no configuration, but nevertheless it shows that port is operating in trunk mode, was it done automatically after creating vlan interfaces?
Actually there is no need to do that on Layer 2 switches (accept for Vlan for managing the switch itself, in this video he made it interface Vlan99). SVIs are created on Layer 3 switch for inter Vlan routing
Please explain what is the use of Vlan 99 and why did you configure native vlan to 50?
@@theFilipinofoodie Vlan99 is for management of the switch itself, it doesn't have to be 99 it can be any Vlan number, but you should give an ip address to it. Native Vlan will be untagged on trunk port, so that devices can use it.
Does it is used to hit telnet ssh too???
i have question, is it really necessary to enable interface vlan on the access switch that is not in use? Here the management is VLAN 99 and it should be the only activated interface vlan on the remote switches.
Hola como debería hacer para configurar el router de Internet1, por ssh con la vlan 99, porque esta en otro segmento, la vlan99 172. 16.99.254
Hey thanks for the videos its pretty much helping, i have a probleme. I have this network lan1(with different vlan) => switch => router => router => switch => lan2, i configure an ospf routage on routers but the ping does not work between the same vlan on different lan
Can someone help??
im confused on the vlan 50. why did it become the trunk vlan intead of vlan 99?
Question is why enabled int vlan 10,20,30 on all the access switches? It could be just vlan 10,20,30 and assigned edge devices but why int vlan 10,20,30 on access switches when we don't assign then ips,????? Any reasons for it? Int vlan 10,20,30 should be defined on layer3 switch but why on access?????
How do I configure uno switch 3650 between 2 routers 2811.
Can you show us how to configure the actual layer3 switch.
hi can you help me with a problem with my labo about packet tracer ?
Where are the links for the two source files?
hi mr Saleh
how to vlan 10,20, 30 pc can ping to vlan99 use for telnet purpose
Why use 3 switches? I mean why cant just connect the two switches directly to the L3 switch? Please give reason why?
صراحة فيديو جميل و اذا ممكن أستاذي أتواصل معك معي مشكلة ف النتوورك اللي سويتها و اذا ممكن تساعدني ف أكون شاكراً لك
I like this video, how can I see more videos on your channel?
My channel is Saleh Al-Moghrabi, there are more videos there,
@@MrSaleh970 thank you
No ping success from switches to cloud g0/0?
Configure a default route on the MLS or a dynamic routing protocol.
@@MrSaleh970 i'm a beginner...can you tell me how?
I can't ping from a pc to MSL G0/2??
I will do the lab and explain it thoroughly so soon, thank you for your feedback .
@@MrSaleh970 it's fine! I just forgot to give the pc's a default gateway 😬 thank you for responding!!
Marie Verlinden glad to hear, best of luck.
well Thank you for posting it but i wish you slow down and explain what you'r doing not detailed steps
Articulate demonstration.