How Much Horsepower Will GT40 Intake Make Vs. Stock 5.0 Intake ADD BOOST!
Vložit
- čas přidán 27. 08. 2024
- SMASH LIKE, SUBSCRIBE AND BELL FOR NOTIFICATIONS OF NEW VIDEOS!
Here we go again. Making horsepower with less parts. How to install, Test drive, Dyno Time and Race track results. All one video! Stock Block GT40 intake w/ SUpercharger. Old school style FMU! Enjoy!
SUPPORT THE CHANNEL! teespring.com/...
JOIN THE NEOMUSTANGS MEMBERSHIP CLUB!
/ @neomustangs
INSTAGRAM: neomustangs
TWITTER: / neomustangs
EMAIL: MYBUSINESS01@HOTMAIL.COM.
#neomustangs #mustang #fordmustang #foxbody #projectcar #streetcar #vortech #gt40 #dragracing #horsepower #stickshift #turbo #foxbodymustang #supercharged #stockbottomend
PLAYLISTS:
TECH CORNER PLAYLIST: www.youtube.co....
PROJECT HOTWHEELS: www.youtube.co....
BLACK CAR: www.youtube.co....
GRUDGE NIGHT RACING: www.youtube.co....
DADS CAR: www.youtube.co....
I've owned 4 5.0 Mustangs. Even to this day it is the platform I would choose to build on.
💯
@@Neomustangs Had a question... I know you have a lot of experience for a while now! A couple of months ago I put a 94 cobra upper intake and gt40 lower from a 90's explore on my 94 SN....
It had a small baffle not like my stock intake with a long baffle. And I noticed I was loosing quite a bit of oil! So I added a oil catchcan to it and, sure enough I filled that catch can every time i drove over 60 miles Can you to tell me by switching to the lower with a big baffle will prevent oil suction through PCV??? Somoene suggested I put a 2nd pcv on driver side valvecover up in front of motor. So I did that and it pulls half the amount of oil then before and runs a ton better but still too much oil for my liking. And it dosnt have blow by to myknowledge.
Currently have a new 333 stroker with 7000 miles on it now in my 94 GT AODE with stock heads
Any help is much appreciated
Your videos are great for all enthusiasts, nobody left out. Simple straight forward real world testing and you aren’t hiding any of the equipment failures we all experience. Kudos for not doing deep pocket mods very affordable using stock parts to boot. Thanks
Thx man. I do have the deep pockets mods on my other cars who sit and watch me do
This lol
I remember driving these cars brand new off the dealer lot...they were amazing!
Yep
Yea I had fun in a few. I Just did a bunch of stuff to a nice 92 LX for a young man. I didn't have the motor open, mainly fixed exhaust leaks, straightened battery/charging system out and tidy up things.
It had trick flow alum heads, Holley intake, bbk Cai headers and flowmasters with 3.73s. I don't know what cam or anything but it ran damn good when I was done with it.
He got the itch and wants to boost it now lol.
@@Neomustangs True story. I bought an 82, 85, 86 ASC Capri and a 90 Lx. I currently road race an 85 Mustang. Currently building an 88 Turbo Coupe with a Faux Cobra Motor. ( Explorer motor with Roller Rockers and Cobra cam.) Best fun a gear head can have.
Glad to see another channel supporting the fox body. subscribed.
Newbie here and I am impressed brother. I'm on my 6th Fox. 85 GT vert
Very very low miles.
My first was an 87 Gt I bought back in 89. Hooked ever since.
Welcome to the channel!!
By your pfp it looks very clean, one of the best looking ive seen in a long while
my 88 fox is nearly identical to yours at a glance minus the spoiler! Yours is waaaay more worked over than mine, but same color, 5 spd, hatch. Youre a man of good taste sir!
Thanks. Ya it’s a simple. Not perfect combo I enjoy
Nice vid bro!!! And thanks for the gt40 intake you sold me years ago!!! Im still rocking it!!!
Nice !
Thanks for the suggestion on the 1.7 rockers for my GT 40 heads last week I hooked everything up so now I have Edelbrock rpm intake GT 40 ported heads 1.7 rockers on a Stockham 14 pounds of boost now I’m working on suspension keep up the great work I love your channel
Right on! thank you!
My favorite is when people say that the stock cars or the gt 40 engines are weak. But they are the same one that wreck em because they can't handle the power lol
I love your show, and FoxBody Mustangs, keep up thd great work I've been a FoxBody Mustang lover my whole life! May the Fox be with you brother, God Bless.
And you as well !
I really appreciate you putting these videos together. Great stuff buddy
Glad you like them!
The E7 heads are a much bigger restriction than the stock intake. Either way, she's movin!
Thats correct. And knowing that, i know that converting to mass air is my only option with GT40 heads. Im arleady doing this intake a disjustice right now ccause it makes more NA and boosted than that. Just limited to 19s.. and no tune ish.
I hate it when people call a explorer intake a "GT 40" ITS NOT A REAL GT40 ITS A EXPLOARE INTAKE. A REAL "GT 40" was tubular
@@bretthusted1167 Here we go.....
@@bretthusted1167 they are very close and also flow the same and also use the same lower. So yes may as well call it a GT40 variant. As far as performance you have a GT40 in the explorer intake for far less money.
I've been a mustang fan for most of my life. I've owned 3 fox bodies and am about to buy my 4th and plan to put some $$ and work into it. Love your videos 👍
Still working on it? Just curious lol
@@chris_htepo Still working on getting another lol. I ended up getting a Navigator not long after I made this comment. Needed something with 4 doors
@@reptilelovers3850 Nice! I actually always wanted something really spacious like that too but somehow ended up with an 89GT lol funny how that works out.
@@chris_htepo I completely understand how it seems to work that way lol
I just got my fox back from being tuned after turning the boost up.... this motivated to get some new track times.... time to see how far 430 rwhp will take me
Let’s go !
With the blower, I would like to see what a fuel pump and 24lbs-ers would do. I feel like the blower setup might be starving a bit at peak.
I love the thought though that this is sort of the way we used to slowly bolt on mods though.
That driver mod I tell ya! Lol I think I seen some daylight under that front wheel when you left. Enjoying the new style of videos! Parts, dyno, track!
Cousin paul says yes.. that happened.
Well I've got my 86 gt 5 speed converted to maf. Can't wait to see what yours does with it. All I'm missing that you have is the pro charger. And I'm trying to find one now. Lol great video as always. Glad to see someone else that likes gt40 as much as me. And not so much Ls swapping these. you can make these cars fast without all the LS BULLSHIT
Nice. And thanks
Taking that oil baffle off of the bottom of the lower intake WILL cause the PCV valve to suck oil. It will pull oil through the cup screen and it will burn that oil. You will see lots of smoke coming out of the tailpipes when you put your foot in it. Ask me how I know!
I'm really liking this build
TY
Can’t wait to see what it makes with gt40 heads
Ya i gotta mass air convert for that.
Bro I love all your videos!
Glad you like them!
Great vid brother. I have a Holley Systemax II on my '89 notch. I'd like to see the difference between the GT-40 and the Systemax.
Noted! Hmmmmm
Me too I have a Holley systemax intake manifold also on my 89 Mustang it maybe it's just me but when I first put it on it felt fast but now that it's been like maybe 5 years it feels like it got slower Maybe the air velocity is low with this intake
@@michaelgarcia3452 This intake didn't make you slower. The Systemax II is the best intake for the 5.0 Fox up to 6,500. Go to an NMRA Pure Street race and look at what intake most of those guys are running. Its the Systemax.
Maybe I just suck at racing
Fully ported GT40 intake manifold has very competitive flow numbers.
Loved this video brother!!! Love it!
Appreciate it!!
Totally agree with you about the maf conversion.I own a stock 86 gt 5.0.plan on leaving stock.So hard to resist though lol.I live in Cleveland and plan on driving it as much as possible before the snow 👍
Yes sir. Will have to convert next year
Great information about the explorer intake. I’m running the gt40 on the Reddemon. Keep the vids coming great tech tips.👍
Thanks! Will do!
Keep grinding, youtube is slow demon. it'll come to ya!
@@Neomustangs thanks brother I appreciate ya. 🙏🏻
@@DEMONFOX5.0 YW man!
I've only ever heard it was the years 1996-97 for explorers
If you're going to take time, money, and effort swapping heads, there are a lot better options than gt 40 heads. Beautiful car brother. Love the the video.
Thx but price wise vs hp gains there really not.
@@Neomustangs are used aluminum heads for good price not available anymore, sorry been out if Foxbody scene for awhile
@@msk3905 even good used aluminum heads are significantly more than iron gt40 heads.
I paid $1,800 for a set of aluminum gt40 style heads. They have 2.02" intake valves and 1.6" exhaust. I could have gotten away with spending $600 on a set of rebuilt cast gt40 heads but I had a few extra dollars laying around. The front of the car is about 60 pounds lighter with aluminum heads. But best bang for buck would be cast, hands down.
Stock parts,killing it!💯
Always!
Damn that car is beautiful!
Thx
Thx
Always go turbo 😊
Cool test. I like seeing what the little things do
Thank you!
I love the step by step with the SD Mustang....lets me know where I need to go with mine.
Question, do you have A9L's in your store? I need to trust the seller and I've bought parts from you in the past and trust you aren't selling junk. Let me know, thanks and keep on keeping on!
Yes I do! And if theres an issue i alwasy back it up> I have some ECU's i havent sold yet. I usually take them apart to make sure the capacitors arent bleeding or bad before i test them. ANd i repair that when they are.
@@Neomustangs thanks! I'll go check your inventory for it. I'll get with you out there if I don't see them
@@jpp9846 ok
Love the cars and the projects, great channel. These 5.0s were my dream cars in H.S. Do you build engines for customers? Thnx.
We Enjoy watching your channel 👌 Great vibes , We definitely support big time 🥂😎
Thx man
Good video bro
Dude that’s solid! I’m trying to dial my fox in but only for 1/8 mile racing
Good luck!
Yep next big jump would be a decent aluminium head. I wouldn’t even bother with the GT40 heads.
I’m waiting for my money tree to start popping out cash. Branches have no leaves damn it.
HAHAH right!
gt40 intake, gt40p or gt40 heads, cam, probably tfs1 or a b cam, longtube headers will make no where near 350rwhp but will definitely have some torque to it. which for a street car, is more important.
always like gt40 videos. best bang for the buck
The Explorer intake is a small improvement. The original GT-40 intake from ford racing was made from tubing. It will pick up a few more horses. Not sure how rare those intakes are today?
The car is plain out of space to make power on 19s. I think 30s and.a tune it makes more power right now
Very rare and people think they’re gold when they try to sell them. I’ve been them listed for $1,500 in some of the foxbody fb groups
Good stuff. Love the info.
Ty
These might not be the fastest cars anymore(not that many of them ever stayed stock anyways lol), but man, there are few cars as cool as a clean fox body, especially now that they're one of the elder statesmen of the Mustang crew.
Thanks and yes
That cover underneath the lower intake keeps hot oil from splashing onto the runners and heating up the air going into the engine. On any intake, wet or dry, it's good to get the covers off underneath and clean all the gunk before installing on a new/fresh engine--otherwise it's like doing an engine swap without flushing the radiator out.
It's worse than that. The PCV valve will pull oil through the cup screen at high rpm and the engine will smoke.
Thank you for all of the info!!!!
Any time!
About time that car hit 11’s. Should have just threw 24 or 42 injectors on it before intake swap
Ya did that and failed. It’s speed density. It don’t like to
Rowing gears like a Boss. Good Job! You running stock t5?
Yes and yes
Congrats on your 11:90!! 👍👍
Ty!
You can make more power with speed density. Use the megasquirt computer
I know I can make much more with other tuning too but that wasn’t what I wanted to do here
Love your channel!! Keep up the good work. Format, amount of tech, etc is Perfect!
Stock disc in fmu? Whats the fuel pressure and boost at the top?
Not sure but its 45 with vac off idle. Stock FMU yes.
New to the channel. Love it. Curious what rear tires you are running?
One dads car? 275/40/17s
Nice vid man, I'd get the tires more centered on the top of the rollers.
Thanks for the tip
Hey thanks for all the great videos ! How important are torque box plates on a stick turbo mustang ? Second I have drag radials but car didn’t hook in first gear 6lbs of boost . 315 60 r17 tires
Pretty important to keep an eye on. If you go
Race just buy a secondary set of rear wheels and put slicks on it. Be done with it. Same the street drags for street to drive around ok
Great video!
🔔😎
Springs, rockers, and intake about plus 20.
So what rockers change?
Ratio, full rollers, ??
Just intake plus 10?
What cam?
I ran a 12.9 with f cam and aluminum heads, dam I need to throw on my supercharger
Evan Smith did that in a GT stock full interior totally stock engine back in the 90s when he had MMFF magazine.
Revnevan on YT.
Do you have a preference of the GT40 over the GT40p? From my research the GT40p is slightly better but only up to about .500 lift due to the smaller exhaust valves. So if you intend to run any cam with a higher lift you have to port them so the GT40 is actually better for a higher lift cam.
P over regular but you just have to understand the spark plug dilemma
@@Neomustangs Oh yes. It is going in a Ranger so that is definitely being considered.
Run the maximum lift possible with a particular duration. The earlier the flow maxes out, the longer the flow stays maxed out = more area under the curve = power.
I’d be curious what the difference is between the stock intake and the GT40 over the whole curve, not just peak HP. Congrats on 11’s!
Never thought to do that. I should have layed that over top each run.
@@Neomustangs search Richard holdener pretty sure he has dyno
E7 heads are very limiting. Upgrade heads to take full advantage of that intake system. 👍
The whole point was doing a simple
Experiment with simple numbers. These are multiplicative with tuning and larger combos
I have a 94 gt with a 302 or a 5.0 if you will. When i got it it was skipping. So i tore the top part of the motor down and pulled the heads and come to find out the stock e303 cam didny have enough clearance between the cam and push rods and we kept bending the pushrods. Then the second time i tore it down to replqce the pushrods i took the heads off. And replaced the single spring with dual springs. Put it back together and it wouldnt run for shit. Then i am tearing it down now and placing a new 512 comp cam with gt40 heads with new lifters and new rockers and new pushrods.then i put a exhaust system which was a borla off road H pipe with no cats Hopefully this will be the last time if nit. I. Yanking the 302 out and dropping a 383 stroker bore 60 over in to it
Sounds like your hands are full there !
Nice job.
Thanks !
I hope you can test 87-93 maf sensor in 4.0 explorer 70mm and sensor in sn 4.6 80 mm housing, all ford parts after all, it was easier to pay c and l
Right.
New to the channel-Love the content🙂
Th
Extrude hone that intake and port match the lower along with a set of ported GT40 heads and car will make a lot of power.
Still have to maf convert.
I did the same and added a 1inch spacer between upper and lower and its 👍
BigDogs ported is much more cost effective.
Nice video man
Thanks for the visit
Hey do yourself a favor and get the Holly Terminator x harness mass air system.... you won't be disappointed.
Plan to go 10s on a stock speed density motor and nos first. I already own term X
Awesome Content!
TYVM
If anyone is interested, I have a complete GT40 set up for sale Heads, upper and lower Intake. As well as Y303 SVO Ford Motorsports Aluminum Heads with SVO 1.6 roller rockers, Trickflow push rods. Located in Central Ohio.
Awesome stuff.
Thanks!
I'm a little late on this series, but I love you pushed the SD system. Everyone is so quick to covert to mass air and while the SD has it's limits, if you stay within them, it runs pretty good. I'm about to put a Novi 1000 on my stock 88GT and had a question on the check valve. Did you just run it inline to the map sensor or T it in and let it vent to the atmosphere?
Thx i agree! the check valve is in line with the vacuum hose that runs from intake because SD doesnt vent to atmosphere.
@@Neomustangs Thanks man!!! Seems like some people put it on a T fitting and let the boost vent to the atmosphere, but I'm going to take your route and just put it in line.
Love the videos man just got a vortech v3 sci they forgot to send the spring tensioner pulley tho so now it's just a waiting game. Any way, just curious what psi your running. Thanks in advance!
Thx for comment. It’s only 7 pounds
@@Neomustangs how many horsepower per pound of boost?
Seems like being supercharged 19lbers would be way to small o would think 30s 36s or 39s would be more fitting
This works off an fmu.
What’s the timing at? Im guessing 14-15
Yes 15
What about the F-150 big-port 5.0l intakes? Nobody does those???
@11:49 I felt that! 🤘
Yes sir.
This is my other channel. I'm Strokedmustang66
I will def check it out!
Nice car! Aww those svo seats? Did you have to strengthen them?
Nah just 86 GT
Once you convert to MAF, put some 36lb injectors/Billet fuel rails and F303 cam in the car. Porting the heads, extrude hone the upper and port matched lower as well. Did this on my 93' Cobra back in the 90's and the car ran 11.75 at 123mph on its best pass. This was rolling out on a street suspension and not a 5k dump as didn't want to break anything. MSD Boost retard back then and some help with 116 octane. On 93, car would run 119-120.
Nice thanks for the info!
@@Neomustangs Some crap on the alpha cams from Ford, but that F303 was a blower specific cam. I paired very well my my GT40 Irons, 1.7 rockers, cobra style GT40 intake, 65mm TB and Pro-M 77mm MAF. I was running 10lbs on the old B Trim that was the predecessor to the S Trim. I have an archaic vid posted on my channel from the 90's if you care to hear it. Not seeking subs, just making a reference to hearing the chop of the cam.
Other than hood clearance issues, I’m curious to know why mustang racers don’t use the EFI truck upper & lower intakes??? They’ve got longer runners, it’s a dual throttle body and there’s larger diameter truck throttle bodies available from the aftermarket too!
Curious myself.
Neomustangs me especially so due to current and vehicles 10yrs old or less all for the most part can be either factory retuned using factory software or tuned with aftermarket software without removing the EGR if equipped or any emissions components. Obviously, that’ll only go so far then it’ll be necessary to remove all emissions and go all out for performance.
In my case since I need to remain street legal and within EPA & CARB meaning (instant inspection fail if a check engine is on) but, I’d like to get as much power from upgrades like your doing with old blue except the need to keep stock EGR & emissions A.I.R. pump and equipment with at least high flow catalytic converters.
My current application is a 1985 Mercury Grand Marquis LS 2-Door, 302 nothing special 0.030” over bore with stock rockers, pushrods, flat-tappet hydraulic lifters, stock E7 heads & intake with RV cam, EGR & Complete AIR system with TAB & TAD valves, EGR control & EGR Valve solenoids, A/C throttle kicker, Choke control & Exhaust heat control valve all are electronically controlled and vacuum operated and all working, stock 2BBL CFI Fuel injection & TFI Ignition, stock exhaust manifolds with one O2 sensor on passenger side, 8.8 LSD with 3.73:1 gears 28-Spline axles on P225/70R15 tires on 15”X7” 5 on 4.5” rims.
In the last year I’ve installed the following new parts, HD spring assisted front shocks, air assist rear shocks, full 2.5” exhaust, magnaflow high flow AIR Assisted Catalytic Converters, H-Pipe, dual flowmaster 40 series mufflers & tail pipes over the rear axle, head gaskets, lapped the valve seats, new valve seals, double row timing set, new front & rear main seals, one piece oil pan gasket, intake & exhaust gaskets, replaced all sensors including EGR Valve, replaced all vacuum lines with new lines, installed a Monster Transmission AOD built for 400HP/450torque with slightly higher 1,600 - 1,800 stall torque converter (factory was 1,300 - 1,500) made a mount and installed three 15” X 7.5” X 3/4” trans coolers 3/8”s ID, made new 3/8”s trans cooler lines added trans temp sensor in the return line, added remote mounted spin-on oil filter for the trans.
Removed entire engine harness except harness that goes through the firewall, repaired any shitty Factory Ford wire slices, ran new sensor wires for a tach, coolant temp, oil pressure & trans temp into the factory harness loom, 4-pod A-pillar gauge pod with autometer 2-1/16” gauges, wired PWR & GND for gauges into stock harness loom, wired the gauge lights into the headlight/dimmer harness loom, soldered/shrink tubed all connections and replaced all factory loom tape with Tessa tape & flexible split loom all for stock appearance and fitment, replaced old frayed 10AWG alternator charge wire and fender to block grounds with 8AWG wire, replaced 4AWG PWR & GND’s and added a block to frame 4AWG GND, added a 8AWG GND for the alternator to the regulator on the fender to assure good charging GND’s.
Installed new severe duty water pump & Fan Clutch, new 3-Row radiator without factory skimpy trans cooler, new stock 70AMP alternator, new belts, all new hoses for cooling, heating and emissions, fabbed up a functional 2”T X 12”W X 18” hood scoop with fabbed 18” X 4” air cleaner housing to seal under the hood with stock 9.5” X 3” air filter, new distributor, wires, E3.42 spark plugs, new factory 16GAL fuel tank, fuel pump & tank level sender, basic maintenance new fuel filter, air filter oil change & filter, new brakes front & rear, new tires, new 800CCA battery.
My problems are, EGR Insufficient Flow fault code and no idea what parts to upgrade to stay reliable, good idle, more power and stay CARB inspected. My idea is a sleeper that has good fun power, ok cruising mileage and passing state inspection. I’m not by far trying to break and power records here, just a fun old paw paw sleeper car, no turbo, NOS or forced induction except for small ram air hood scoop.
Nothing beats the tubular gt 40 intake from ford
They all make same hp lol
@@Neomustangs did you try tubular one from ford motor sports
I have one i know
@@johnrau2873 .....they did a comparison many years ago on Muscle Mustang and Fast Fords magazine. Same exact HP rating. Cobra/explorer/tubular. Fact explorer outperformed it by a few Hp/TQ
There i posted the muscle mustangs chart on my blog so you can see it. They did a dyno test on all three intakes. All 3 intakes use the SAME lower style. Only uppers are different.....
Mine came from ford racing back then
That intake was about 9 hundred
They only made a few of them
The one that came off explorer's are close
Great video. Iam a subscriber and will follow you. Just bought 93 gt. About 4 months ago. Here's what my set up is. Wondering if you could ballpark my HP? 5.0 stock bottom, gt40 heads, cobra intake, e303, BBK shorty headers, BBK 65mm throttle body. 70mm mass air, 19lb injectors, BBK H pipe, Flowmasters, 3:73. Thanks Darryl,
Nice !
@@Neomustangs what kind of HP you think iam around? Ball park. What else would you recommend that i could do besides, ( supercharger, turbo, nitrous)? I like it to be street / cruise and dependable, granted stuff happens. We are in our early 50's, and a FOXBODY it's a great way to go MID LIFE CRISIS. LOL. Fun car to drive / cruise. Much appreciated. Darryl
Seems like that distributor may be giving out or spark plugs are too cold. On the power pull unburnt fuel was puffing. Slight bump up in timing and fuel will say yay or nay! Would raise fuel pressure first to verify that it isn't a lean misfire!
Untuned you’re gonna have that a little. It’s not that bad. But ya. Timing maybe. But then I’m being greedy in an already super lean situation I’d imagine
@@Neomustangs oh damn! Did not knownit wasn't tuned
MSD are like magic.
Hard to find any definite answers on this but can I use the Explorer accessories drive on an Explorer motor if I put it in a Mustang Foxbody? Explorer alternator , Power Steering pump , water pump, A/C compressor on the Explorer brackets?
Honestly I would just use the long block and swap all the foxbody parts over.
@@Neomustangs that would definitely be the best route to go. It’s HARD to find a foxbody 5.0 with accessories that’s not in a car. Guess maybe find a foxbody with a clapped out 5.0 HO, would be the best route.
How much work is it to convert to mass air for gt40 heads? Love the videos 🤘
You dont really need to convert mass air to use heads.
Gt40 intake was never that great of a mod. The car would way cooler with the stock intake. 20hp nitrous woulda put it into 11's....
Nitrous is a possible next week mod. For shits and gigles.
It would be cool to see what nitrous would do
I always had good results with the Cobra intake. More power and 500 more usable RPM up top...
The cool part of this build was how fast could it go with stock parts. Change the stock intake he might as well drop in a Roush nascar long block....
Did you loose any boost psi with the new intake? This is a cool ass project👍🏽
None
Neomustangs Time for that fuel system and 10lb pulley! Let it eat🤔😝
Did that fucker just pull the left front wheel while only making 325?! I can’t wait to dive into my LX.
Yes
Hell yea 11.90s on 19s nice
Yes!
Listening sir I have a '91 F-150 and I'm very curious why I'm not why how can I and what do I need to have to change my F-150 engine is not a ho just a regular 5.0 out of a 91 my question is first what kind of ECM PCM will I need the code the three digit code and two what would I need to install also to ensure that this thing runs correctly
If I could put a vortech where the ac compressor goes on my 5.0 explorer swapped ranger..or a torq storm..
Ya that would be cool
I just watched your video I liked it.... just kinda wondering if I could get y'all opinion on my setup to what kinda power you think it might have I've got a 306 speed pro 4 valve relief pistons, gt40p heads intake, exhaust runners been gasket matched and cleaned up under the valve s been cleaned up stock valves with a 3 angle valve job, b-303 cam, 1.7 roller rockers gt40 intake 24# injectors long tube headers 65mm throttle body not sure on the mass air meter.... just like to have your thoughts on thanks
William
Dyno
i got a question for you. i have a 91 5.0 i just picked up. its running like pure shit at idleand def has what seems to be a miss. i changed the tps, coolant sensor, new plugs, cap, and rotor. it is still doing it. its idleing so bad its like it has a cam and a miss lol. i just cleaned the egr and throttle body as well but waiting on gaskets. the funny thing is i can remove a plug wire and it doesnt change. not only that you cant even tell you removed a wire. almost forgot i checked the timing as well and it was gtg at 12 w spout plug out. im at a loss on this one man. do you have any suggestions or anything else i may be missing. i just bought the car 4 days ago and have been chasing down this issue. any help is appreciated. thanks in advance
Im going to be honest it needs to go to a reputable tuner and get looked at. Sounds like possible ignition or dead hole in the motor. Check compression.
Nice hit!!!
Thanks !
Just got an early sn95 with the 5.0, also in ohio!
Nice !
I have a 302 with gt40 3 bars have been wanting to cam and heads but I am curious if gt40 intake will still perform well with aluminum heads and larger cam the engine is in a 1984 datsun 200sx. I barely clears the stock hood i am afraid a different intake would require hood mods i like the stock look to this car it did come with a 4 cylinder the v8 really runs well in the car
Yes it will.
Go for the shorter 93 TBird, 94-5 Fox uppers.
The intake curve actually reduces turbulence into and out of the TB a little. Appearance is subjective.
So you think it would only make 20ish more rwhp with GT40 heads and long tubes?(legit question) I was hoping the gain would be atleast 30-40hp with the heads since boost is involved. I'm planning on the GT40Ps with my little Novi blower and that's disappointing. Lol I thought they were usually good for 25ish hp NA. BTW, love the channel man. You and Brew2l have the best content!!!
We will be revisiting this
@@Neomustangs I'll be looking forward to it. 👍👍
You bet!
Lots of variables.
Casting roughness, valve job, bowl ridges, good springs, etc. Minor details.
There's 10 HP difference easily.
Northeast Ohio shout out thx Dan
West Park (44111) here my 89 needs some track time brother !
Let’s go !
Would you be interested in another quarter horse I was going to run it on my fox but switched to Holley terminator
I’m all set thx tho
Need to put an intercooler on it
Bah going turbo next speed density style lmao!
So this car only has 19# injectors, stock heads with valve springs and roller rocker? No cam no nothin? No headers/exhaust? Basically GT40 intake and a super charger? I'm just curious for my own build. How much boost is that supercharger making?
That is correct. 7 pounds at 4500.
What can you do for power in an emissions state ? Supercharger ?
Dyno numbers are great to talk about for some people but do not always equate to a good et. Your car proves that 330whp can run 11.90’s. I know guys that claim 460whp and are stuck in the 12’s.
Weight, Trans, driver can all contribute to slower car on the track.
Thats true.