On a 4-stroke, it's true. But on most 2-strokes, having no baffle will actually gain more power. Most 2-stroke race bikes don't even come with baffles from the factory. So an aftermarket exhaust is kinda pointless.
A little history. This engine was created after WWII in Ukraine (then part of the USSR), after which it was produced in Kharkov and later in Leningrad. In the 2000s, the Chinese copied it, changed the volume and shape of the cylinder, removed the spool intake, and installed electronic ignition. But the shape of the body, its dimensions, clutch, and drive sprocket remained from the original from the 50s, made in the USSR. Live with it.
I beg you to buy another 2 engines and mount all three of them on a single bike. You will need welding, but I am sure that is no issue for you. You can mount them over or behind the rear wheel, connect all of the engines to a new axle with chains and then connect the new axle to the wheel using a single chain.
Motorized bikes are the best dude. So cheap, highly customizable, tons of performance, awesome hobby. An actual solid mode of transportation too. It's actually pretty straightforward, just watch some in depth videos on how to do it. Just get a large frame bike if you can, not to hate but this bike was janky especially without being able to pedal 😂
You still need the peddle side chain to get started. Think moped... Also those wheels are going to make you wreck at speed. When you start feeling the heat on your arse pull over. It is your rear axle heating up and will snap and High side you. Speaking from experience 🤙🏻 🚴🏻♂️💨✨
@@JB_Lego I was going 60mph and slowed down to 45 when I was feeling the heat. That's when my axle snapped and half of it fell out of the bike. The wheel started violently wobbling and I took it into the grass and that is when the wheel flopped to the right and steered me to the left which high sided me onto my right side. Slingshotted me. I bought a set of Gemini's to stop that issue from ever happening again.🤙🏻 🚴🏻💨✨ ✨🇺🇲✨✝️🙏🏻✝️✨🇺🇲✨
@@Zane.Wellnitz all my bicycles have been stable into the 40s. I haven't found any safe downhill to get them any faster. A Scott Voltage MX3, Giant Yukon, Saracen Helix and some Viking Race. The bearing did eventually go in the Scott but I rode it a lot - a few thousand miles with a bafang kit - and the replacement wheel was good. A bit blustery at 47 mph due to the wind but no speed wobbles or mechanical issues. Also is the heat of a bad bearing even noticeable above the engine or simply using a back brake? Potholes however. Killed a rim hitting one at 35 mph. Nearly threw me off the bike! Thankfully on the Scott with tough beater rims with 36 spokes and not the dainty Saracen road bike.
Did you make the fuel mix any richer for the NOS? More oxygen = more fuel to go with it. Do you have any two stroke oil in there, cause if you don't it will kill the engine. Also, the left brake is the front in America? Weird.
It has to be broken in before using nitrous and u need to b at top end speed before using nitrous so the piston doesn't explode and the nitrous kit needs to be attached to the intake for a better performance gain
That engine is screwed. You guys need to break those motors in! I literally just bought a pexmor 100cc a month ago and the break in is vital!! I’ve since then moded everything you can and ported and polished mine and changed sprockets. Mine does 60+ mph now.
@Stinky_Couch_Pickle they are acctually very power full when you take the stinger out the exhaust and take the sponge out the air filter drill some holes in the air box and 2 holes at the end of the exhaust and pedal with the bike i swear you can get up some really big hills I think they are deacent to be honest
You should get rid of the old sprockets front and rear, and then get rid of them peddles and weld some pegs cause there isnt really a point in pedals. Also I am getting a 50cc 2 stroke kit for a small supercycle. I have got rid of the front sprocket and am leaving the rear. It is almost done 😄
Y’all gotta stop pestering my boys about the sprocket video I I think maybe he shouldn’t have shown the sprockets on CZcams before making a video about them but
No way dude, that's just how it is. Maybe he is disfigured from an accident or something, and doesn't want to show anything, except the crazy shit he does 😅
Just put in a random amount of gas and oil. Then zip around at full throttle. Then attach Nitrous and zip about, all before a good break-in period. I guarantee this bike will be toast in a short time.🚲
When’s the sprocket vid?
Real
Soon😊
you need that "baffle" for the exhaust to function as an expansion chamber. without it you loose alot of power
Those are very poorly dimensioned, taking them out actually helps.
On a 4-stroke, it's true. But on most 2-strokes, having no baffle will actually gain more power. Most 2-stroke race bikes don't even come with baffles from the factory. So an aftermarket exhaust is kinda pointless.
His neighbors have to hate him with how loud he is lol
It's a 2-stroke, you have to put the mixture in the petrol
100 💯 oil with petrol mix
A little history. This engine was created after WWII in Ukraine (then part of the USSR), after which it was produced in Kharkov and later in Leningrad. In the 2000s, the Chinese copied it, changed the volume and shape of the cylinder, removed the spool intake, and installed electronic ignition. But the shape of the body, its dimensions, clutch, and drive sprocket remained from the original from the 50s, made in the USSR. Live with it.
Awesome bro, but hurry up with the sprocket collection video 😂
And a bigger NOS bottle.
what do you mean you wont be able to pedal thats like most of the point of a motorized bicycle you start it by pedaling and releasing the clutch...
I just run start mine I got tired of adjusting 2 chsins
@@teeco5952so you just took the stock chain off?
I beg you to buy another 2 engines and mount all three of them on a single bike. You will need welding, but I am sure that is no issue for you. You can mount them over or behind the rear wheel, connect all of the engines to a new axle with chains and then connect the new axle to the wheel using a single chain.
Glad u built one of these thier super fun I got 2
I have one of these I built and you keep the basic bike chain on to be able to pedal start it! That's the whole point!
wouldnt the engine spin the pedals?
Motorized bikes are the best dude. So cheap, highly customizable, tons of performance, awesome hobby. An actual solid mode of transportation too. It's actually pretty straightforward, just watch some in depth videos on how to do it. Just get a large frame bike if you can, not to hate but this bike was janky especially without being able to pedal 😂
But illegal in my country 😢
Why did you take the chain off the bicycle chain?
Hi im from Australia 🇦🇺 where do u buy the nos bottle holder from thats on handle bar when nos button from ?
No. Nope. Nos substitute not a great port work, a well dialed carb etc... kid.
You still need the peddle side chain to get started. Think moped... Also those wheels are going to make you wreck at speed. When you start feeling the heat on your arse pull over. It is your rear axle heating up and will snap and High side you. Speaking from experience 🤙🏻
🚴🏻♂️💨✨
Damn my bearings are just a little worn from going 50+km/h
@@JB_Lego I was going 60mph and slowed down to 45 when I was feeling the heat. That's when my axle snapped and half of it fell out of the bike. The wheel started violently wobbling and I took it into the grass and that is when the wheel flopped to the right and steered me to the left which high sided me onto my right side. Slingshotted me. I bought a set of Gemini's to stop that issue from ever happening again.🤙🏻
🚴🏻💨✨
✨🇺🇲✨✝️🙏🏻✝️✨🇺🇲✨
@@Zane.Wellnitz what kind of junkyard bicycles are you riding?
@@TimpBizkit a board track racer and a 125cc dirt bike. What is your issue?
@@Zane.Wellnitz all my bicycles have been stable into the 40s. I haven't found any safe downhill to get them any faster. A Scott Voltage MX3, Giant Yukon, Saracen Helix and some Viking Race. The bearing did eventually go in the Scott but I rode it a lot - a few thousand miles with a bafang kit - and the replacement wheel was good. A bit blustery at 47 mph due to the wind but no speed wobbles or mechanical issues. Also is the heat of a bad bearing even noticeable above the engine or simply using a back brake?
Potholes however. Killed a rim hitting one at 35 mph. Nearly threw me off the bike! Thankfully on the Scott with tough beater rims with 36 spokes and not the dainty Saracen road bike.
Why don't you start it which pedals
Did you make the fuel mix any richer for the NOS? More oxygen = more fuel to go with it. Do you have any two stroke oil in there, cause if you don't it will kill the engine.
Also, the left brake is the front in America? Weird.
When is the sprocket video
They don't fit lol
@@forrift7845 lol
It has to be broken in before using nitrous and u need to b at top end speed before using nitrous so the piston doesn't explode and the nitrous kit needs to be attached to the intake for a better performance gain
Great videos. you deserve more views.
No link to nitros tank?
@zoominalways hope you mixed oil in petrol or it will sieze
16:00 we have a "fuel issue"
Where can I get the nitrous kit
Hey camera man, you blew it ! You missed the crash !!!
holy crap thats a long intake runner! Im still watching, lets find out!
ngl i forgot abt the nos till he reminded me 9:20
VERiNICE !
GRREAT SUCCESS !
i have a motorised and it goes 90 its aboustly crazy love ur videos btw
Mine goe 105
needing an exhaust to be on for a 2 stroke motor debunked - zoomin always 2024
Great video bro thanks for sharing it
I have 2 of these! They are fun. Except when I installed the motor I kept the entire bike intact
the golf cart build please????
They did it already I think
Link for kit?
When doing burnout throttle and dump the clutch
That bicycle kit sounds just like my 74 ke100
A poor guys surron
man u own a nitro rc car shut up
bruh
These can be quite expensive with all the upgrades you can do I’ve got one with £250 ish into performance parts
Sprocket vid?
Yo, can you like link this kit?
That engine is screwed. You guys need to break those motors in! I literally just bought a pexmor 100cc a month ago and the break in is vital!! I’ve since then moded everything you can and ported and polished mine and changed sprockets. Mine does 60+ mph now.
Why would you take all the gears off the back madness
I dont think you would ned the gears since its now petrol powered. I dont know what kind of derailleur would be needed for all that torque
@Stinky_Couch_Pickle no I mean pedal with it like an e bike
@@Motorizedstuff yeah, I realized what you meant afterward as I looked closer at his setup.
@Stinky_Couch_Pickle they are acctually very power full when you take the stinger out the exhaust and take the sponge out the air filter drill some holes in the air box and 2 holes at the end of the exhaust and pedal with the bike i swear you can get up some really big hills I think they are deacent to be honest
@@Motorizedstuff insane bro!
I always replace the studs with bolts😅💯
Time to do a lot of upgrades and mods to the engine.
It’s technically snorkel now😂
Happy to subscribe to you guys.
You should get rid of the old sprockets front and rear, and then get rid of them peddles and weld some pegs cause there isnt really a point in pedals. Also I am getting a 50cc 2 stroke kit for a small supercycle. I have got rid of the front sprocket and am leaving the rear. It is almost done 😄
true, thats an option! I think the pedals are for keeping the bike as a pedal-assist catagory, obviously the speed ruins that tho!
You guys are basically making a dirtbike but with nitro lol
16:00 we have a "fuel issue" ofc it looks like there aint no 2stroke oil in the gas its clear as day!!! xD RIP piston&cylinder
Why take the gears off, that's what keeps it a bicycle, my dad built two and never did anything to the gears.
I got the exact same kitten that's awesome
Bruh I got the exact same bike. So only a 85 cc one would fit not 100cc bruh that’s what I tried the 100cc to big
dat carb intake stole all yor power
W vid
finna try this
Big zooming!
remove the plastic cap that you used to put the nos in (the bike wil have more torque)
no bardzo dobra robota 👌
It takes 40:1 oil n gas
Must be a hard life having a gold helmet welded to your skull.. :(
Gota film dat shit lmao over the bars
yeah man i give it a B+
15:48 😂😂😂😂😂
bro was huffing gas
Insane
Bro this kit is so simple to use and operate how tf you messed it up that much, brain is missing
Now record video tutorial how to put in nitro !!!
I have hybrid bicycle motorized+electric
HELL YEAHHHHH
Talk about a boost
I love it
add a shift kit
Goes a lot faster if u cut the muffler off
How not to install a motorized bike kit 😅
SPROCKET VID!!!!!
NOOOOOO NITRO ON THE ROCK CREEK IS *W I L D*
Bro thats a pocket bottle 😂😂😂
sneaky pete kit lol
Remove the muffler cap!
Zooooooooooooooooooooooooooommmm
450 swap it now
STRAIGHT PIPE IT!!!!!!!!!!!!!!!!!
Y’all gotta stop pestering my boys about the sprocket video I I think maybe he shouldn’t have shown the sprockets on CZcams before making a video about them but
Just attach a go pro to helmet.....
the prob is... is super slow😢
and to expensive $200
you 2 dont need nitrous that's for sure
Hey bro, try a expansion chamber type exhaust on it, it'll give you a power band.
Yoo
ankle burner 500
Dude shut up and let your friend build it 💀
Dont break my bike youll pop a tyre are you saying your friends fat 🤭
Sprocket video or else we are un subbin
More oil
switch gears😂
Walmart fall apart
Take the entire exhaust off
Buddy of mine had one and we had no zaust on it and it sounded like ass but was noisy
B
Face reveal😊
No way dude, that's just how it is. Maybe he is disfigured from an accident or something, and doesn't want to show anything, except the crazy shit he does 😅
Bıke 90 $! wtf so freaky cheap
No it isnt
Just put in a random amount of gas and oil. Then zip around at full throttle. Then attach Nitrous and zip about, all before a good break-in period. I guarantee this bike will be toast in a short time.🚲
First
Big deal
Yeah it is a big deal
the fuel filter is upside down
What a damed waste of money. Go. Get a job.