How to Replace Front Wheel Bearing 2009-13 Mazda 3
Vložit
- čas přidán 9. 09. 2024
- Buy Now!
New Wheel Bearing & Hub Kit from 1AAuto.com 1aau.to/ia/1ASH...
Worn bearings can create lots of annoying noise, and wear out tires unevenly. Watch this video to learn how to install a new bearing and hub in your 2008-13 Mazda 3.
• Check here for more videos on the 2008-13 Mazda 3: • Mazda 3 2nd Generation...
This process should be similar on the following vehicles:
2010 Mazda 3
2011 Mazda 3
2012 Mazda 3
2013 Mazda 3
Tools you will need:
• Flat Blade Screwdriver 1aau.to/oCQ/1AX...
• Pry Bar 1aau.to/oh3/1AX...
• 14mm Socket 1aau.to/oCU/1AX...
• 32mm Socket 1aau.to/oU/1AAS...
• Bearing Race and Seal Driver 1aau.to/oh/1AXA...
• Press
• Snap Ring Pliers
• Straight Cutters
• Ratchet 1aau.to/oFs/1AX...
• Socket Driver
• Socket Extensions 1aau.to/oCU/1AX...
• Torque Wrench 1aau.to/osF/1AX...
• Brake Parts Cleaner
• Copper Anti-Seize
• Liquid Thread Locker
• Paper Towels 1aau.to/oeM/1AX...
• Rust Penetrant
• Center Punch 1aau.to/obR/1AX...
• Floor Jack 1aau.to/ojE/1AX...
• Hammer 1aau.to/oio/1AX...
• Jack Stands 1aau.to/oiH/1AX...
• Pick 1aau.to/ogj/1AX...
• Wheel Chocks
• Wire Brush 1aau.to/oc6/1AX...
Subscribe: / @trq
Check out our playlist:
Mazda 3 2nd Generation 2008-13: • Mazda 3 2nd Generation...
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.
√ *Watch the Video*
√ *Buy The Part at 1A Auto* 1aau.to/m/Shop-TRQ-Parts
√ *Do it Yourself*
√ *Save Money*
I noticed some serious damage to the bearing at 4:30. Was the due to wear or using the press?
I appreciate that you are using the old bearing instead of a fancy press with proper adapters. Not everyone has the right tool available!
+Benjamin Lagace Thanks for watching our video! 1aau.to/m/Shop-TRQ
Great video, I have no issue with paying my mechanic to do the work.
You guys don’t get enough credit. I buy a lot of Mazda parts from you guys and you guys are amazing. Videos are definitely the best too
+Kwon Orange Thanks for the feedback, we greatly appreciate your business! 1aau.to/m/Shop-TRQ
Best video on youtube for replacing wheel bearings.Should have many more views !. Thanks for laying out every detail for doing this job, especially the the press work.Thanks again !!
Great video. It must be nice to have such rust free parts to work with. Just getting the rotor off was almost impossible on these vehicles if they are rusted. You literally need a sledgehammer to do it if its rusted on.
You gonna cry?
I used this video as a guide for my hub/bearing replacement.. excellent man!
I wish my bearing would have came out as easy as yours! I had to douse it with PB Blaster until it gave up!
+Benji Mann Thanks for watching. Buy the part in this video on 1AAuto.com: 1aau.to/m/Shop-TRQ
Just gave that like button a loving bonk. Great video.
Thanks for the video, loving bonks cures everything :)
The crowbar tricks to lock the wheel is a great idea but it ruins the threads of the studs, use a screwdriver through the caliper to the inside of the vented brake disk! It's a wayyyy better way. We did exactly as you did on the first side and we damaged the threads on a stud and need to replace it
Great job but those ball joints where toast. Would have been prime time to replace those...good video 📹
Let's continue on replacing this bearing so we can continue on driving! 😊
Great informative video!
+sch1181 Thanks for watching our video! 1aau.to/m/Shop-TRQ
Great video! Thank you!
Quick question - how many tons is the press. I tried with 6 ton press and couldn't get the bearing nor the hub out.
Thanks. Very good instructions!
+Wojciech Gurak Thanks for watching our video! 1aau.to/m/Shop-TRQ
You definitely had me at loving bonks.
Video looks great!! Thank you for using a torque wrench and sharing the torque specs!!
Very good video for this procedure
Thanks man I followed your instructions and I did my front wheel bearing car is silent and smooth
You had all the press?
I def need to take my Mazda to mechanic cause this is a lot of work with tools that I do not have
Wow. This is quite the job. Of course I had the castle-nut spin with the stud in the tie rod ends. Such a pain in the ass.
Such a nice video. Thank you! 🔥🔥
wouldnt you grease the hub shaft before inserting dry into bearing assembly
THANK YOU VERY MUCH . VIDEO VERY CLEAR
+hung nguyen Thank you! We love empowering our customers and showing how to perform DIY auto repairs with our high-quality auto parts. 1aau.to/m/Shop-TRQ
Do you think a Diy can do it himself? I don't have a puller or a press
thumbs up!!! true shop do it all!! good job
Great video well explained
Is the wheel hub, bearings, and spindle sold together already assembled so I don't have to do all the dismantling and pressing?
Good stuffs 👌 very informative 👍👍👍
Assuming we have a press in our garage. 🙄
Excellent video....!!!!!
I need the whole knuckle with the hub and bearings..do they sell it one deal.. I bent the part that held the caliper bracket on. How it bent the knuckle not sure
Hello, is it a must I replace the the hub as well? It seems to me that it’s just a piece of metal with No moving parts. Could I reinstall the original hub?
Yes you can reuse huv
Just got front wheel bearings for my 04 Mazda 3. The spec sheet in the box says to tq the axel nut to 39 ft lbs the go 90 degrees past that. So do I just do that or tq to the min tq at 172 ft lbs?
Thanks 👍
Do these bearings not need greased before installation?
do you press out the old bearing from the inner race?
Ausome video 👍👍👍👍
Hello
I have a question, can you use the old hub and replace just bearring? Thank you
Yes you can. This is what was done in the video 👍🏻
@@neuideals588 Oh it looked new to me...maybe he just cleaned it up?
I have reason to believe my bearing was replaced backwards. I have no speedometer or abs or blind spot monitor. Can I check If the bearing is backwards without disassembly?
Good vid !
what size of socket is required to remove the hub? 32mm?
Yezzir
@@NewDemons666 what size is the inverted torq socket
?
Does this Work on 09 Mazda 3 s hatch
Good work
Well done !! Thank you for sharing ... :)
"keep in mind it`s a small bolt and you don't want to break it, snug it up and torque it to 68lbs"
All i need to do is remove the wheel hub to put on new wheel studs, i dont want to remove the whole assembly.. is it possible to do without press
+Jesse Osborn For this specific part, you will need to use a press when replacing the bearing.
Would it have killed you to say WHAT SIZE each bolt was when removing??
God thats a lot of work.
i guess you really do need a press to do this job. I was hoping to be able to hammer old one out ?
Were you able to do it with a hammer?
do it your selfers dont all have presses. oh boy
Why not replace the LCA as well??? Worried about a wheel bearing but not the control arm ball bearing that’s blown out. How comical.
Shit. Think I’ll just get a new car, this seems extensive
I torqued the wheel bearing axle nut 4 times😂
Did you guys steal this video from 1a auto