Thanks for your video, it was very helpful, but I'd like to add a couple comments for clarification. 1. You can reach both sides without removing fenders or major components. I found it easier on the driver's side to remove the fuse box cover and the top air dam (6 plastic rivets). 2. If you're removing the power supply cable (not essential but helpful) squeeze on the sides of the white plug, NOT the top and bottom, to disconnect it, at least on a 2011 Avalon. 3. The first cover is about 3 1/2" diameter and looks like an aluminum heat dissipation cover. Rotate it counter-clockwise a few degrees using the two tabs for leverage and pull out. Be careful not to pull too far as there is a braided strap connecting it. 4. Inside of that is the contact points to the bulb. Grasp the outside (approximately 2" square metal block) and rotate slightly counter-clockwise. You can now remove both the cap from number 3 and the contact block from number 4 and remove completely. 5. There are two wire retainers that hold the bulb in place. Starting with either one squeeze it towards the center and pull it out from under the tab that secures it. Repeat this procedure on the other side. The retainer wires will now hinge downward and release the bulb from the socket. 6. Reverse the procedure when replacing the new bulb. When replacing the new bulb be sure that the notch is aligned so that the bulb sits securely in the base. I don't know if this will help anyone, but there were a few instances where the video had you turning it the wrong direction or removing the plug incorrectly. Forcing in the opposite direct risk damaging components.
This video was the only place I could find on the web on how to remove the HID ballast and get down the the HID bulb on my 2011 Toyota Avalon. I bought the car used and had no idea what was going on. Thanks for taking the time to post this video!
I really appreciate your video. It really helped me get the $7,000 lightbulb installed. Are their diamonds in them or what? Seriously, I would not have been able to figure it out without your video. I have a 2011 Toyota Avalon. Thanks.
Thank you so much for this video. Seeing as this particular set up only came out for 2011 and 2012 it's very difficult to find any vids or anything on these cars. They are kind of rare...but once again thanks for this. I will be replacing the bulbs on my 2011 Limited soon since they dont seem to shine as bright as they once did when I first got the car.
thank you for the video...now way i would have figured out on my own without breaking something...when taking the first plug out....you pinch the sides inward...should wiggle out after a few tries....otherwise super easy!!! I just need to take out a loan for the next bulb that goes!
I bought some aftermarket bulbs on Amazon for $26 for a pair. They were rated at 4.3, but for the difference in price I thought I'd give them a try. You can also choose your light color by ordering different ones. I installed them and they work and look great. We'll see how they hold up. www.amazon.com/gp/product/B01KSTL2Z4/ref=ppx_yo_dt_b_asin_title_o04_s00?ie=UTF8&psc=1
Thanks for your video, it was very helpful, but I'd like to add a couple comments for clarification.
1. You can reach both sides without removing fenders or major components. I found it easier on the driver's side to remove the fuse box cover and the top air dam (6 plastic rivets).
2. If you're removing the power supply cable (not essential but helpful) squeeze on the sides of the white plug, NOT the top and bottom, to disconnect it, at least on a 2011 Avalon.
3. The first cover is about 3 1/2" diameter and looks like an aluminum heat dissipation cover. Rotate it counter-clockwise a few degrees using the two tabs for leverage and pull out. Be careful not to pull too far as there is a braided strap connecting it.
4. Inside of that is the contact points to the bulb. Grasp the outside (approximately 2" square metal block) and rotate slightly counter-clockwise. You can now remove both the cap from number 3 and the contact block from number 4 and remove completely.
5. There are two wire retainers that hold the bulb in place. Starting with either one squeeze it towards the center and pull it out from under the tab that secures it. Repeat this procedure on the other side. The retainer wires will now hinge downward and release the bulb from the socket.
6. Reverse the procedure when replacing the new bulb.
When replacing the new bulb be sure that the notch is aligned so that the bulb sits securely in the base.
I don't know if this will help anyone, but there were a few instances where the video had you turning it the wrong direction or removing the plug incorrectly. Forcing in the opposite direct risk damaging components.
Thanks you for the tips it’s really helpful .. Just changed mine and I wonder if there’s a ways to adjust the lights up and down ?
@@Hsukhaybir nope
thanks for the video, I was thinking the same but the instructions in the manual do not account the the HID bulb type...U R DA MAN!!!!
This video was the only place I could find on the web on how to remove the HID ballast and get down the the HID bulb on my 2011 Toyota Avalon. I bought the car used and had no idea what was going on. Thanks for taking the time to post this video!
I really appreciate your video. It really helped me get the $7,000 lightbulb installed. Are their diamonds in them or what? Seriously, I would not have been able to figure it out without your video. I have a 2011 Toyota Avalon. Thanks.
Thank you! For the video and link to buy the bulbs! It was so difficult to find a specific video for the HID replacement.
Thank you so much for this video. Seeing as this particular set up only came out for 2011 and 2012 it's very difficult to find any vids or anything on these cars. They are kind of rare...but once again thanks for this. I will be replacing the bulbs on my 2011 Limited soon since they dont seem to shine as bright as they once did when I first got the car.
You're a lifesaver... thanks for the video.
Thank you for this! You saved me a trip to Toyota because I too could not figure that out.
No problem I will keep posting vids for this car as I go
thanks. i want to learn how to install led strips inside the interior
I appreciate you man, thank you
Great vid!
Yup
Perfect easy understand
Good thing I didn’t pull the engine first
Thank you!!!
Good job 👨
Thank you
thank you for the video...now way i would have figured out on my own without breaking something...when taking the first plug out....you pinch the sides inward...should wiggle out after a few tries....otherwise super easy!!!
I just need to take out a loan for the next bulb that goes!
Just so you guys know, these bulbs are available on Amazon for $29 dollars a pair. DMEX D4S.
THAAAANK YOU. Jesus lol
Wat are the bulbs for the fog lights 9006?
I have a 2011 limited avalon and I need the bulb and ballast I think. Well it is not called a ballast for the 2011. Do you know anything about it?
How did you replace the drivers side? You mentioned removing bumper?
Same way you dont need to remove anything. I tried removing the fender but it's just a waste of time
Where do you buy the bulbs from?
Auto zone has them
Any auto parts store should have them or try amazon or ebay
I bought some aftermarket bulbs on Amazon for $26 for a pair. They were rated at 4.3, but for the difference in price I thought I'd give them a try. You can also choose your light color by ordering different ones. I installed them and they work and look great. We'll see how they hold up. www.amazon.com/gp/product/B01KSTL2Z4/ref=ppx_yo_dt_b_asin_title_o04_s00?ie=UTF8&psc=1
Could you do a video on how to change the fog lights and which bulbs to buy
@mick mick you have to access it through the wheel liners.