Dear Sir Drive is tripping on overcurrent fault. But actually no overcurrent, taking Normal current while tripping. Please suggest how to solve the problem.
In parameter 11.04 - set the minimum speed which is required, in there video, it's 0, set as required. & On HMI - 1-89.1% is the reference given by control room to run the VFD (out of 100%)
Sir. As per my knowledge, DTC mode is selected only for applications where high precision of movement is needed. For general,scalar mode is okay. Torque is generally unchanged : -300 to +300 is set
Sir. It's very thoughtful observation u did. Great. As of now I don't know surely y its VFD motor r connected in delta but... In my observation, I have seen only HT motors (6.6kv) are connected in Star , they need very high torque while starting of equipment. Else all LT motors are connected in delta. Still, I'll check for better results and revert ASAP sir. TQ
Dear Sir, Thank you for your video, I kindly need your help, ABB VFD ACS800-01 , some parameter groups do not show up on the local control panel, the only parameter groups that show are 10, 11, 14, 16, 33 the rest do not show. And also the language selection which should be in group 99; it shows in group 33. I could not find any related setting in the drive manual. any clarification, please
You must speak with your ABB service engineer. I am also a field engineer, do not know that much in details. If you still need help I can talk to my ABB service engineer but he is chargeable.
I want 440volt output voltage at 27HZ nominal frequency I have set I have set all parameters as per name plate data in para. 99 ... The voltage is still 415-420 volt output what should be done else for getting 440volt output at 27Hz freq output frequency.
I believe these drives are designed for 0-50hz frequency only with 0 Hz= 0 V and 50 Hz = 415V, But, you can change the minimum and maximum speed in the limit parameter, you will get the desired voltage at 27Hz. Try this, if u don't get, text me back
@@bishantkumar12589 I have checked in limit parameter 20 here min freq. I setted 0 hz and maximum 27hz then also output voltage is 415volt as I set 440volt nominal voltage in para 99...here I m not seems minimum and maximum RPM setting
@@bishantkumar12589 currently I am testing without load and I seems voltage does not boosted to 440volt and I have tested 4pole motor with this parameter nominal voltage 440volt nominal frequency 27hz and motor design for 415v, 50hz due to motor gets overloaded at this stage even at no load .. It was trial at 4pole motor actually I want to test 440volt , 27hz , 12pole motor which is under production
Assalamu alaikum Hamare pas ACS800 drive hay jes may group 99.1 se direct 99.9 pe chala jata hay motor data nahe araha parameter stat group 14 se ho jata please help Younas cherat cement
namaste ... aapke drive me kisi ne parameters ko lock kar diya hoga... parameter number - 16.02 PARAMETER LOCK , check karo aap. agar 65535 hai too lock hai, 0 hona chahie.
Sir hamare pass ACS 800 hai.. usme fiber optic thi mod bus ke sath hoke PLC ma communication jata hai.. Abhi fiber optic ka light thik hai fir fir bhi communication nhi mil raha or.. Eroor hi ata hai.. communication module 7510 vala
@@bishantkumar12589 in my case I am getting fault in LT drive as ACS800 Temperature fault when we operate above 2nd step speed where as Temperature is normal inside E room. Please suggest what is the remedy? Thank you..
Kys bt hai bht acha Tariqa r zbrdast Information maza agya
Sukriya sir. Please share with your electrical team 🙏
Very informative video 🙏🙏👍
Thank you sir 😊
please support the channel...
subscribe and share
Thank you sir, valuable video. But it's a standard software. Plz make a video hoist software.
thanks sir for your for making this vidio please make more this type of full vidio on all vfd and mainly yaskawa and danfoss and delta
Okay sir.
Love brother
👍
Thank you sir....🙏🙏
Dear Sir
Drive is tripping on overcurrent fault.
But actually no overcurrent, taking Normal current while tripping.
Please suggest how to solve the problem.
Put the drive to scalar mode and check veeresh Anna
@@bishantkumar12589 Sir it is not Tripping immediately, it is tripping after sometime.
How to set control Board temperature and it can Bypassed?
Sir How to set minimum speed that motor will achieve while starting VFD? and sir what is "1- 89.1%" written in the Top of the digital display?
In parameter 11.04 - set the minimum speed which is required, in there video, it's 0, set as required.
&
On HMI - 1-89.1% is the reference given by control room to run the VFD (out of 100%)
Thank You Sir! I have one more doubt ,What is meant by Jog speed or when we select Jog speed ?
Thank you Sir...I have one doubt how can i clear maximum fan running hours alarm in ABB ACS 800 VFD
czcams.com/video/_pyCuF5zLFo/video.html
Sir. Please check this LINK ...
Pl support the channel... subscribe and share
@@bishantkumar12589 Thank you Sir....Subscribed...expect more useful videos
Thanks
Sir plz make a video over dtc mode selection and parameters for dtc mode and how to set range of torque
Sir. As per my knowledge, DTC mode is selected only for applications where high precision of movement is needed. For general,scalar mode is okay.
Torque is generally unchanged : -300 to +300 is set
@@bishantkumar12589 okay sir
As I know, torque is different in star and delta but why motor always connect in delta for vfd control.
Sir. It's very thoughtful observation u did. Great.
As of now I don't know surely y its VFD motor r connected in delta but...
In my observation,
I have seen only HT motors (6.6kv) are connected in Star , they need very high torque while starting of equipment.
Else all LT motors are connected in delta.
Still, I'll check for better results and revert ASAP sir. TQ
Why can't given information about ID run. Its important Parameter.
It's big topic sir and there's a complete separate video on it. U may check my ABB playlist for all the details
Dear Sir,
Thank you for your video,
I kindly need your help,
ABB VFD ACS800-01 , some parameter groups do not show up on the local control panel, the only parameter groups that show are 10, 11, 14, 16, 33 the rest do not show. And also the language selection which should be in group 99; it shows in group 33.
I could not find any related setting in the drive manual.
any clarification, please
You must speak with your ABB service engineer.
I am also a field engineer, do not know that much in details.
If you still need help I can talk to my ABB service engineer but he is chargeable.
@@bishantkumar12589
Yes please,
I would be so grateful to you Sir
would you share your email or WhatsApp number so i can send you the photos and video
Sir,
If I operate drive to MCC panel.
Is put same parameters according yo this video pls confirm.
Yes. Parameter remain same mostly
I have Acs800, I have problem that acs800 have fault BR Wiring (7111), can you tell me how to fix it?
Sure sir. I'll check and let you know
BR WIRING
(7111)
3.17 FW 5 bit 1
Wrong connection of brake resistor Check resistor connection.
Ensure brake resistor is not damaged.
How I can increase rpm hz settings while drive is running on profibus mode
Sorry, I don't have that information. Pl contact your service engineer
I want 440volt output voltage at 27HZ nominal frequency I have set I have set all parameters as per name plate data in para. 99 ... The voltage is still 415-420 volt output what should be done else for getting 440volt output at 27Hz freq output frequency.
I believe these drives are designed for 0-50hz frequency only with 0 Hz= 0 V and 50 Hz = 415V,
But, you can change the minimum and maximum speed in the limit parameter, you will get the desired voltage at 27Hz.
Try this, if u don't get, text me back
@@bishantkumar12589 I have checked in limit parameter 20 here min freq. I setted 0 hz and maximum 27hz then also output voltage is 415volt as I set 440volt nominal voltage in para 99...here I m not seems minimum and maximum RPM setting
@@durgeshkadu8181 what's the speed at 27Hz. ?
@@bishantkumar12589 currently I am testing without load and I seems voltage does not boosted to 440volt and I have tested 4pole motor with this parameter nominal voltage 440volt nominal frequency 27hz and motor design for 415v, 50hz due to motor gets overloaded at this stage even at no load .. It was trial at 4pole motor actually I want to test 440volt , 27hz , 12pole motor which is under production
How to ser drive parameter using vfd drawing
Assalamu alaikum
Hamare pas ACS800 drive hay jes may group 99.1 se direct 99.9 pe chala jata hay motor data nahe araha parameter stat group 14 se ho jata please help
Younas cherat cement
namaste ... aapke drive me kisi ne parameters ko lock kar diya hoga... parameter number - 16.02 PARAMETER LOCK , check karo aap. agar 65535 hai too lock hai, 0 hona chahie.
@@bishantkumar12589 janab shukreya check kar ke aap se contact kar longa. Unlock ka koe pascode hay??
@@user-nl4yc5vq3y ye too apke company ka incharge ya abb service engineer wala hi bata sakta hai kya set kiya hua tha
agar aapko mere videos saahi lagte hai too please apne electrical dosto k sath v share kare is channel ko. thank you
@@bishantkumar12589 zaroor karonga
hi sir, my abb acs 600 drive have i/o comm fault.what is the reason and how to troubleshoot and solve.
Sir,
I have Acs 800 drive how to speed control by Protections meter.
Kindly share Basis parameters Acs 800 drive.
Ok sir. I'll in some time
@@bishantkumar12589 sir,
Can your share mobile number? Pls
Sir acs800 vfd me encoder ko bypass kaise kre
50.06 set internal estimate
How to reset complete parameter
Factory reset can be done 👍
Sir abb ACS 1000 main water temperature reference setting kon se parameters group main milega please reply
Check kar k reply karta hu
ABB ACS 800 vfd parameter UPLOAD & DOWNLOAD using Drive 🪟. Please make 🙏 a video please 🙏 Sir.
Using HMI/CDP is available
Sir Drive window se kaise karte h uske procedure chahiye
@@Fire_palace thode time me upload karta hu
Bro kindly explain master slave parameter of acs800 kindly share
Ok sir. I'll surely try to work on it ASAP
Moter stop hone ke bad reverse aa rha hai ky falt ho skata
Motor reverse run ho raha h kya ?
Ha sir rukne ke bad thoda reverse ghum rha hai kis parameter ka problem ho skata hai sir please tell us
@@earntechsv5384 pump application hai kya ?
Nhi sir EOT CRANE ME ABB ACS 800 DRIVE LAGI HAI USKA USE FORWARD REVERSE MOTION HAI USI KI PROBLEM Hai
@@earntechsv5384 okay main check karta hu
सर ACS लिखा हैं मॉडल मे उसका मतलब या फूल फॉर्म क्या होता हैं
ACS bus family group ka naam hai.
Sir hamare pass ACS 800 hai.. usme fiber optic thi mod bus ke sath hoke PLC ma communication jata hai..
Abhi fiber optic ka light thik hai fir fir bhi communication nhi mil raha or..
Eroor hi ata hai.. communication module 7510 vala
Parameters me bahut try kiya pr vo error nhi jaa raha
Check kar k bolta hu sr
ONCE CHANGE THE OPTICAL CABLE AND TRY TO OPERATE THE VFD
Danfoss drive ka video kijiye.
Okay sir 👍
Hello sir 🙏 app k what's up number chahe sir Mai Nigeria Mai Job Kar hoo mera question tha Discussion Karn hai plz Sir. From odisha Jay Jagannath 🙏
Hello bhai. Kya problem hua h. Batao. Kaun si company me ho waha ? Quantum group?
Sir how to contact with you...plz
Pl ask ur doubt. Here
@@bishantkumar12589 in my case I am getting fault in LT drive as ACS800 Temperature fault when we operate above 2nd step speed where as Temperature is normal inside E room. Please suggest what is the remedy? Thank you..
@@bishantkumar12589 I want to send a problem video clip