Honda Odyssey 2019 Install Hood Deflector
Vložit
- čas přidán 25. 08. 2024
- Dial2Fast is supported by its audience. When you purchase through our links, we earn an affiliate commission from qualifying purchases.
Honda Genuine Parts 08P47-THR-100 Hood Air Deflector
amzn.to/2rWZbN2
Or Buy From Ebay:
bit.ly/2018Odys...
Tools:
TACKLIFE 26PCS Magnetic Screwdriver Set with Case
US: amzn.to/2jMU7KC
CDN: amzn.to/2nwAGag
3M Double Sided Tape - 7/8" wide
US: amzn.to/2YvNeOH
CDN: amzn.to/3gtIGPd
========
In this video, I will show you how to install the front hood deflector on a 2018+ Honda Odyssey.
The installation is not difficult. Just follow the step by step guide in this video and you will have no problem installing this accessory.
IMPORTANT: After installing this, I notice the metal bracket from Honda is angled too much which eventually will cause the double sided tape to lift and come off. Removing the old double sided tape and putting new one on will not fix it. The ONLY fix is to bend the bracket open so it isn't angled too far down, therefore releasing any stress on the double sided tape. You will need to adjust the bracket angle so that the hood deflector will simply rest onto the bracket with very little flexing.
To remove the old double sided tape, you can warm it up a little with a hair dryer, then rub it off little bit at a time with your finger. Then clean surface with rubbing alcohol and reinstall new 3M double sided tape (see link above). Also clean the surface on the hood before reinstallation. Use the original template as a guide.
=======
Shop Dial2Fast Store For List Of Tools & Parts
US: www.amazon.com...
CDN: www.amazon.ca/...
=======
Support Dial2Fast on Paypal
www.paypal.me/...
Support Dial2Fast on Patreon
/ dial2fast
Dial2Fast website
www.dial2fast.com
Like us on Facebook
/ dial2fastofficial
Shop Amazon
US: amzn.to/2LqTtuk
CDN: amzn.to/2L5QASt
Join Amazon Prime
US: amzn.to/31i05mP
CDN: amzn.to/3kG0D0R
Try Amazon Prime 30-Day Free Trial:
US: amzn.to/2S3GjHI
CDN: amzn.to/3kG0D0R
========
As an Amazon Associate, I earn commissions from qualifying purchases with the links provided here.
I wish there was a grille guard available, to reduce deer collision damage.
Thank you sir. The installation instructions worked perfectly.
The 2019 Ridgeline Hood Air Deflector (P/N 08P47-TG7-101) installation is the same with the only exception being that there are four (two on each side) hood brackets. The Template that comes with the Deflector has the cutouts for both brackets. Also all four are the same and you do not have to worry about which side they go on.
Wow straight to the point very well explained
Thanks, very clear and easy to understand your instructions!
Thank you so much for these videos. I just got the same van and so far I’ve been able to install the hood deflector and splash guards effortlessly thanks to your videos. Any chance you’ll be doing the door guards?
Can you make a video how to remove the front grill or how to replace fog light
How does it hold up if you go through a car wash with brushes, or no touch car washes with power dryers? Is it stable?
Hi, how can i install bug deflector w/o brackets?
thank you so very much you are the real deal 😎👏👏👏👏👏👏👏👏
Hi very good and well explained only one question could anyone tell or message me where I can obtain a fitting kit like the one you used . I am in Scotland and unable to find a supplier with kits like yours thanks again for a good video .Andy
Where can I purchase the insulation and rubber seal for under the hood for my 2011 Honda Odyssey Ex ?
thanks for the helpful video.
the factory tape is worthless. i would recommend to let the brackets sit overnight on the hood prior to attaching the deflector. i replaced mine with gorilla heavy duty tape anyway.
I also had the same problem after installing it. I ended up bending the bracket so it's doesn't put so much tension on the double sided tape. It definitely could have been designed better by Honda.
How do you watch the front end of the hood after installing the deflector?!
Great video.
Thank you.
Thanks for uploading these DIY videos. Did you so one for roof rail and cross bar installations yet?
That's one accessory I did not get. I really don't have a need for it, and the cost is very high for the part.
Will it fit 2024 Odyssey touring
Yes
You previously installed 3m paint protection film partial panel on the hood for this Odyssey. Did you remove the film before installing the hood deflector? or did you place the adhesive on top of this film?
The 3M PPF film was not installed on the hood because I planned on installing the hood deflector accessory. There is no need to have PPF film protecting the hood when the deflector is protecting the hood. Also the deflector's metal bracket with the 3M double sided tape could possibly lift the PPF film which I didn't want.
@@dial2fast thanks! keep the videos coming!
Hello, you installed it 1 year ago as I see on timestamp, it really protects well? Does it worth it? Thank you in advance.
Well done
whats the point of a deflector?
It prevents rock chips on the hood
It just helps protect the leading edge of the hood, plus deflects bugs and such so they hit above the hood. To some it adds to the look of the vehicle.
Is it causing any problem in car wash? Is it really protecting hood paint from debris and bugs?
I wash my own car so can't tell you for sure if it's safe, but it should stand up to the big rollers. And it definitely prevents rock chips on the hood. The bugs will still hit the windshield.
If not pushing on the reflector to close the hood, how do you close it?
You don't need to push on the hood to close it. Proper way to closing is hold the edge of the hood up about 1.5' high and then let go so it drops to close. Pushing on a hood to close can actually risk denting the hood as many modern cars has aluminum hood.
No one is going to see the notice label, should've placed it near the hood hinge.
If you need to uninstall, what’s the best way to remove the adhesive on the hood?
Heat it up with a hair dryer or heat gun and slowly rub the double sided tape off with your finger.
Those bracket 3m tapes undone itself automatically after couple automatic car washes on mine
Do you notice any decrease in gas mileage after installing this deflector?
No I don't.
@@dial2fast Thanks I wanted to install one for awhile. Great videos by the way. I'm a late tuner as I just switched to Honda last year.
My 3m strips for the 2 side brackets keep coming off, its too tight of a fit, any ideas?
Yes I did have this problem a few months after installing it. I notice the metal bracket from Honda is angled too much which eventually will cause the double sided tape to lift and come off. Removing the old double sided tape and putting new one on will NOT fix it. I probably tried 3 more times with new 3M double sided tape and it still lifted. The ONLY fix is to bend the bracket open so it isn't angled too far down, therefore releasing any stress on the double sided tape. You will need to adjust the bracket angle so that the hood deflector will simply rest onto the bracket with very little flexing.
To remove the old double sided tape, you can warm it up a little with a hair dryer, then rub it off little bit at a time with your finger. Then clean surface with rubbing alcohol and reinstall new 3M double sided tape (see link above). Also clean the surface on the hood before reinstallation. Use the original template as a guide.
@@dial2fast thanks, ive noticed that, bent the brsckets like u suggested, also I ordered just the hardware kit from honda 35.00 dollars. Its definetly a lot better bending the brackets and just having it rest on them.. keep the vids coming, this is my 1st stop with my DIY projects on my oddy... just purchased my 1st oddy last month 2020 touring.. thanks so much for what you do!
Would that fit on Honda oddessey 2022?
Yes it will fit.
I think it looks horrible with that thing