PCP air rifle sidelever Chamber | Part 3
Vložit
- čas přidán 1. 03. 2023
- In this video I built the trigger for the sidelever chamber and connected the sidelever loading system to the hammer so that when you cock the sidelever the hammer also gets loaded.
part 1: • PCP air rifle chamber ...
Part 2: • PCP air rifle sideleve...
Spring for hammer: s.click.aliexpress.com/e/_DEE...
Buy valve: s.click.aliexpress.com/e/_DeP...
Buy Aluminium tank: s.click.aliexpress.com/e/_DdX...
Trigger spring: s.click.aliexpress.com/e/_DBv...
Grub screws: s.click.aliexpress.com/e/_Dn3...
Bolt: s.click.aliexpress.com/e/_Dew...
Copper rod: s.click.aliexpress.com/e/_DeX...
Aluminium rod: www.ebay.com/itm/112742593373...
5mm aluminium sheet: s.click.aliexpress.com/e/_DBH...
10mm aluminium sheet: www.ebay.com/itm/224709512543...
Drillbit: s.click.aliexpress.com/e/_Dnc...
Thread tap: s.click.aliexpress.com/e/_DFR...
Video of Tank & Valve: • PCP Z Valve 0.3L 4500 ...
I impressed ... this guy... whit that right equipment he change the world of the pcp air rifle for sure!!!!!
Thanks!!! I'm still a beginner, not a talented metal worker yet, so there's still lots of room left for improvement.
Damn over 200k views. Alot of airgunner want to make their own PCPs I know I do. Nice vid
This is incredible just using hand tools and a power drill. Much respect to you my friend. Keep up the awesome work.
Thank you very much, I will improve my designs and make better ones.
@codebuddy8315 well I have to say you are doing very well with what you have!
@@pcpairgunschannel
b. nnnnn
givi j nn
Exelente proyecto Esperamos el acabado amigo saludos
Vai ficar top de linha. Cadê a 2parte.
Wow nice.
Amigo que tipo de metal usas
Howmuch bar would this be?
Just a suggestion, use a countersunk screw to attach the chamber on the hammer housing and remove the threaded part in the chamber so that when you tighten the chamber screw, the chamber will press firmly to the hammer housing.
Yes that's a good idea, I will make a new project soon with a slightly new design, I put a countersunk screw in another spot for attaching it, once i realized that its a much better system.
❤
Codyum bomb good video😬🔥
nice video and thanks for sharing....👍👍👍
Muy buen video te felicito y saludos desde Argentina
Gracias! Saludos!
I watched the video repeatedly, but the size with a thickness of 1 cm has not been announced yet. Can you tell me,. Thanks
Word of advice bro from someone who likes tinkering with stuff like you .
For better results and finish i use a wood router with a end mill cutting bit in it 12mm dia then in the trim router i got a 6 mm end mill bit . Clamp you piece down well and put wood either side your piece run your router over the top with more wood for guides for the router take small cuts at a time the finish is amazing mate ive made a full Telecaster guitar out of Alloy its the Dogs Bollocks 😁😁🤘🤘
This is great advice that would have helped me a lot during these times. Just recently I got a mini lathe, so I can attach a milling attachment and get fairly good results, nothing like from an actual milling machine but still far more precise than drilling by hand and filing the edges.
É feito na pura raça, igual eu quando faço é na raça mesmo, sem ferramentas sofisticadas..!👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏
Nice!
Where did you get the buddy bottle and valve from ?
Buy valve: s.click.aliexpress.com/e/_DByh5fT
Buy Aluminium tank: s.click.aliexpress.com/e/_DdXAbPr
in case you wanna learn more about the valve and the bottle, here's a video I made czcams.com/video/PhGg3MchBMg/video.html
😎😎😎 amazing full power
Thanks brother
OUCH, you made a trigger out of aliminium? Oh that's going to be REALLY safe when it wears a little.
True, from now on I used stainless steel.
The trigger is still fine though
GRACIAS GRACIAS GRACIAS
Wow great 👍
Very nice to assembly of pcp
thak you very much sir, I made another one. Video soon
How long does it take to make this airgun? Seem really long and tedious but very impressive considering you only used hand tool, also it would be a lot easier and faster if you have a lathe or milling machine.
If I have all the materials then i think I could make it in 6 hours or so (not including stock) and as long as everything goes according to plan. Maybe one day i will have a lathe or a milling machine
@@pcpairgunschannel 6 hours damn, if iam the one building it even if all the material available i couldn't finish it in 1 weeks let alone 6 hours, anyway thanks for sharing
Pekerjaan yang sangat nagus ,👍👍👌👌
terima kasih, saya telah menonton video Anda🙏
手製のair gunの工程お見事‼️
日本でキット売れますよ。
グッド😉👍️✨です。
Very good job 👏👏
Thanks bro, your channel is very nice.
Công nhận ông này cưa sắt thép bằng tay vòn hơn máy .cao thủ 😂
vâng, hy vọng một ngày nào đó tôi có thể có được những chiếc máy tốt.
Nice to share 🤔😍
فنان artist
I like this
👍
We're did u get the barrel?
It's from AliExpress, but you have to rifle it yourself with a rifling button
You can just use a crosman barrel. .177 or .22. They come in many different lengths also.
👍👍
Can i use pvc tube for the reciever☺️☺️
Plastic is a bit too weak to hold all the screws together
❤
Are you planning on starting that big bore project?, really impressed with ingenuity of this one, but more interested in making a bigger bore one something 8-10mm
One day I'm sure I will make it, but it's not my next project unless I have change of plans
I will make it either 7.62mm or 9mm
The big bore build will obviously have a bigger barrel and a stronger spring, then I will use a higher pressure rate and a larger tank for more shots. I will also change the trigger system so it can handle more pressure and the gun overall needs a sturdier build.
My aim is to make it at least 100 ftlbs (136 joules)
My next project is most likely a .177 cal with a magazine, if I have enough availability for products. Otherwise I would probably make that big bore air gun
@@pcpairgunschannel very well, do you think the small outlet hole on the value will be an issue for the big bore?
@@Sean-- Not a big issue, a bigger outlet hole as well as a bigger hole the valve stem is against would help a lot, but someone made a 120 Joule air gun with this exact valve and I assume they didn't modify the valve. The valve seal would have to be bigger too, if the holes were bigger.
So I think a stronger spring and a larger bore will do the job, but I will research a bit before doing it.
@@Sean-- I am not getting a response very well from the seller that can sell me parts for 177 cal rifle with a magazine, the big bore air gun might very well be my next project.
i plan to make it 9mm and with a side lever loading system, but i will make it much sturdier.
i am from iraq ..good jop
❤❤
厉害
Muito bom, seu vídeo 👏
👍
41111
What barrel are you using ?
just a steel tube 16mm od 5.5mm id, (22 cal). I rifled it myself using a rifling button.
@@pcpairgunschannelabout how many meters accuracy ?
@@pcpairgunschannel🤔
@@khoannong7212 havent tested but i would assume around 50-100 meters
令人震惊的杰作
ชุดนี้ขายยุ่ที่เท่าไหร่ครับ
Fire cylinder for PSP rifles. Can you make an air gun with the head sir 🤔
What head brother, please elaborate a bit so I can understand
Do you mean can you make a PCP gun with a fire extinguisher? You can but the pressure rate is much smaller, safe at around 400 PSI, can handle 800 PSI with a strong hammer.
but if you wanna make a cylinder instead of the big tank, you would need a welding machine or some big plugs. I don't have them so i cant do it.
Halo
I am from Iraq. I would like to know how much the price came to Iraq because I want a quantity of this work. Please reply
I can't sell it myself, but i have left links in the description to buy the same parts, but my design is poorly planned and the build isn't good in terms of quality.
Unfortunately though it seems the shipping to Iraq is really expensive
San po location nyo
Hm boss mag pagawa ng sidelever chamber?
anh có bán sản mình làm ra không ạ
bạn có thể mua các bộ phận từ mô tả
Buy valve: s.click.aliexpress.com/e/_DePwykl
Buy Aluminium tank: s.click.aliexpress.com/e/_DdXAbPr
@@pcpairgunschannel một sản phẩm hoàn chỉnh là bao nhiêu tiền ạ
👊👏👏👏
Интересно, Эдуард видел этот ролик?
Gdgun известный производитель pcp оружия
쇠톱으로 알루미늄플레이트 자르는거보니 졌다..
도구가 부족해서 아무 것도 사용할 수 없습니다.
@@pcpairgunschannel 당신은 최고다!!
It's nice. But, it has to use regulator. Then it will work perfectly।🖤🖤🖤
Yes, you can use a regulator. Without one u can get about 30-35 balanced power shots
@@pcpairgunschannel Gets a decent shot but needs 1000 to 2000 psi. Which is a bit of a pain. No problem using the regulator. Go ahead।waiting for new Video 🖤🖤🖤
@@bdslingshotking Yes, Maybe the next project will use a regulator. This is at 3000 PSI.
@@pcpairgunschannel best of luck.
@@bdslingshotking thx bro. do u have PCPs?
Anh bạn có bán sản phẩm này không ??
Tôi không thể, chỉ đối với một số phần tôi để lại liên kết trong phần mô tả
@@pcpairgunschannel tôi hiểu rồi, có lẽ là do luật pháp đúng không, nước tôi cũng cấm sản xuất, tàng trữ cũng như mua bán😂.
Dù sao cũng cám ơn bạn nhé 👍
@@ee3371 Vâng tôi biết
Nhưng không nhiều người bán súng hơi ở Việt Nam mặc dù nó là bất hợp pháp?
@@pcpairgunschannel luật của Việt Nam cấm hoàn toàn súng bạn nhé, nhưng do sở thích và công cụ hỗ trợ bây giờ khá tốt nên vẫn có thể chế tạo và sử dụng ấy mà ,':v
I need
The valve and bottle are for sale, link in description
Not safety... Boom. 😇
why sir?
1de
These videos are so cool, really impressive work considering your lack of machinist tools.
If you plan on doing another project in the future maybe you could try an airgun with a rotary magazine, there's some remarkably simple designs that wouldn't be very difficult to add to this design such as this one czcams.com/video/Zg4LnzTyWBo/video.html
Thank you very much sir. That actually happens to be my next plan, but the magazine wont be self made sadly. i also have a plan of making a pcp pistol and a big bore air gun, maybe to them i will add
@@pcpairgunschannel If you ever get a 3d printer, I've seen 3d printed rotary magazines before that you could use.
I'm really looking forward to your future videos, especially that PCP pistol.
ເຮັດຂ່າຍບໍ່
What video is this.... Why not in normal those who want to watch they will watch even it's hours so make it in normal
it's in parts because its not all made at once
Hw
Hyess❤️❤️❤️❤️
what tube size (inner diameter) should i used for a 5.5mm/.22mm pellets? anyone?
5.6mm or 5.5mm
if the tube seller has good precision and the 5.5mm is actually 5.5mm and not like 5.4mm then use it, anything in the 5.48mm-5.6mm range will work okay.
im not buying a barrel... i want to make it for myself so i need to know the inner diameter so that i could get a brass tube from the Market..
will a brass tube of 4×3mm works or the 5×4mm??
@@zatesupdates2339 it's not possible to use a tube with 3mm or 4mm inner dia for 5.5mm pellets as the pellets just won't fit, you need 5.5mm inner dia for 5.5mm pellets. If you can't find such a pipe the best could be 6mm Id tube but the accuracy would be just horrible and the pellets probably will be rotating in the air hitting he target sideways... So I guess if you just wanna experiment by making one without good accuracy 5.6mm Id is best, but keep in mind the accuracy really won't be that good.
Please let me know what you want to build exactly and I'll try to help.
👍
👍👍