QuickJack Hack Followup
Vložit
- čas přidán 13. 09. 2024
- My fellow Automotive Fanatics, I welcome you to my channel for another DIY HACK!
Today, I am providing a 6-month update to the simply and cost-effective way to hack your QuickJack! I revised the ball bearing rollers used and show users exactly how the hack works.
Items you’ll need:
6 - 1” ball rollers
3M double sided tape
Large zip ties
3”x3”x5/8” wood block
1hr of your time
If you guys have any questions, please post below and I will do my best to help. As always, thank you for watching and supporting my channel! Until the next time, this is Peter, The Automotive Fanatic!
Product here: www.harborfrei...
Music provided by: Mixkit.com, “Hooligans” by Michael Ramir
Holy Cr*p Peter! Wish i would have seen your video much sooner - I store my quickjacks on it's sides on a small rolling dolly i made so that i can move it to the side of the garage when not in use. When i need it, i roll the jacks to each side of the car via the dolly and set the jacks on the garage floor, but sliding them to the correct position was a paint in the butt....until now. thank you so much for the hack! Now, once i repair my power unit - it started leaking hydraulic fluid out of the manifold section - i will install these conveyor ball bearings ASAP. thanks again
Hey Khoi, glad you found this video useful! Moving the QJ around, is definitely something I did not enjoying doing as they are heavy. Good luck with your repair though!
Thank you for your update video! I was worried they would leave divots in your garage floor.
and off to harbor freight!! :) Thanks again Peter
Awesome, glad you found the video useful!
Yes, thanks for the update!
Glad you found this.
Would be nice to see the rise on the single bearing side to. Thanks.
Thanks for the suggestion Charles, perhaps I will do that the next time I use the QuickJack.
you know what, I will try two of the small ball bearing in each side(it state 55lb each), I have a low car and probably will buy the cusco ramp like in your other video too...
Give it a shot. I just found that the larger ones roll better.
Thank you Peter !!!
For sure!
Thanks for the follow-up, Peter! I've hacked your hack and improved it. I mounted the ball rollers to the part of the QJ that stays in contact with the floor when lifted. It's much more stable that way, and those Harbor Freight ball rollers are known to be bulletproof. This way, I can roll my car around once it's up in the air and know I've got a much more solid foundation. (Read: humor)
Hello Dirk, Thank you for supporting this idea. If I understand correctly, where you mounted the bearings allows you to move the vehicle around while it's up? Wouldn't this be exceptionally dangerous because at anytime, 5K lbs could crash the bearings. I'm trying to grasp the idea from a safety standpoint.
Happy New Year, @@TheAutomotiveFanatic! I was joking in my comment --> "(Read: humor)". Apologies if it missed the mark. Yes, you have a wonderful hack and it works well today. And NO, I do not use the Harbor Freight ball rollers to move the car around once lifted. She remains firmly planted on the floor once up.
I suppose some super duper ball rollers could do the job, but not the ones we get at Harbor Freight. :)
@@dirkvanvelzen9030 sorry Dirk, I totally missed it!
Set Playback Speed to 2.0 and watch the video in half the time.
I know Padwan, I tend to speak too much.
@@TheAutomotiveFanatic You don't talk too much. You give great instructions. I speak about as slow as you do. But I always test instructional videos to see how fast they can go, and then leave a note to others, and people thank me for it mainly because they never thought of it. It's helpful to speed up videos when watching multiple how-to videos.
@@dsbennett Thanks for your insight. I think making shorter videos with direct, to the point, conversation would be best. I still think I speak too much though. LOL.
Can you give a part number or where you purchased the bearings? I just got my quick jack for Christmas and am seriously considering your modification, thanks a lot!!!!
Mike, you should without question, do this hack! Here is the info for you:
www.harborfreight.com/1-inch-roller-ball-bearing-67060.html?_br_psugg_q=roller+ball+bearing
anybody know if 5/8 or 3/4 inch ball bearings wheels would work ? I am worried about the height of QJ fitting under car . Thanks
You may need to use a riser ramps to give you some clearance if height is an issue.
How do those ball bearings work if there is some sand on the floor. I have a dirt driveway and a concrete floor garage? I just cannot keep all the sand out of the garage floor.
George, before I coated my garage, I had plenty of dirt and debris. I know it's not the same as your sand issue, but I do not see you having any issues. The main concept with these bears, is that the contact surface is small so it should roll over anything, even if it's stuck.
What is the additional height added when using all 1" inch roller bearings? It looks to be < an inch from the video.
The location where I installed the 1" roller added about 3/4" to the minimum height of the lift.
Hello Peter, how does this modification performs on your Porsche. I have one too. In my case, there is only 5 inches of ground clearance. I'm concerned about the ball bearing not clearing the ground when the top rack contacts the bottom of the car.
I have done the mod and it works fine on my 2012 911 using the shorter lift blocks
Works fine on my 2009 911 (997.2) with the shorter lift blocks. I might try the taller blocks are some point, but the shorter ones work fine.
Can you provide wheel bearing product and part # info as well as source?
Thanks for the suggestion, description has been updated.
Where did you get the 5/8" thick wood from?
HomeDepot
How far from the joint is the rear bearing?
2 1/2"
@@TheAutomotiveFanatic I ended up using 4, 1" roller bearings on each jack (front positioning using 3 rollers appeared to need at least 1" thick wood, so just used 4 total). I set the front ones 8" on center from the front hollow rod. The rears are set 8" on center from the hollow rod closest to the cams. 3M vhb tape was used to secure them. This positioning adds about 5/8" to the overall height which is very reasonable. Thanks for the hack idea! I've only used my QJ's once and immediately did the mod just to make moving them around easier.
@@russelllen8413 Thank you for your exact measurements. Hopefully future QJ owners will see this and try out your placement.