Installing the kickstart assembly on a Yamaha SR250 (Exciter)
Vložit
- čas přidán 9. 03. 2013
- Here is a photo of the finished install
flic.kr/p/rfeXUF
The pieces that you need to buy and the written out instructions (in Spanish) are on this website. Click on "Manual instalación pedal arranque":
sites.google.com/site/clubsr2... - Auta a dopravní prostředky
2023 and this vid was very helpful thanks for keeping it alive. Just to note on UK bike the idle gear should be the other way around to stop it catching the inside sump. Thanks again
You can buy the parts including the gasket from a Yamaha OEM part retailer like partzilla and sometimes they have them on ebay, too.
Wish I fitted my new kickstart shaft myself I know it was an easy job now watching I know how easy it is
Push the kickstart assembly into the hole. Then turn it clockwise while still pushing it into the hole and you will have accomplished the same thing. Maybe I made it sound more complicated than it is in the video.
Great video, Would it be to much to ask to get a list of the part numbers needed for this conversion? Thanks in advance
Thanks for posting!
The black thing between my thumb and index finger at 0:12, right? Good question. It's a metal cap with a rubber outer layer that will pop out if you hit it hard enough. You want to hit it from the inside of the crankcase going out so you will need something blunt to hit it with. I read that someone did it with a hammer and crankcase screw. Make sure to clean the whole afterwards to get a good seal.
if I order the parts, how do I put the assembly together? The manual makes no reference to kickstarter. do you know which other kickstarter can be used on the sr250
Just what I needed, thanks!
Yes you can. With all the parts added up it cost me about $80
Do you know how to fit one onto a XVS250 ?
Thanks for this video man!
So good to see you here haha! I am doing this tonight! SR250 Community Unite!
i've learned from this quite a bit yet I still can't find an kickstarter for my yammy. I've seen the OEM site but these parts are sold individually and I am not certain I can put them together correctly. There is nothing about this in my factory service manual.
Thanks for the video, nice job on it. How did you knock the little plug out of the right side engine cover that the kickshaft is gonna go through? Do you knock it in towards the motor or out like you are knocking it through the cover? Did you heat it up at all? Thanks
Work on 02 ttr225
Was wondering can I add a kick starter on a 2009 Yamaha WR250X?
Hi, I'm looking for the shaft engine for my yamaha special, do you know if there are another engine to use from another yamaha? thanks
Do you know which bike's kickstarter would work on this bike?
I've checked around and read that the XT250 and SR250 share the same engine, but the SR250 never got a kicker. True?
Do you have some serial number or any information of a kickstarter that would fit this bike?
Bhai kya main 220avenger me kick starter lga sakta hu...
Will this operation work on an Yamaha SR250 from '99?
Awesome, thanks!
hi, your video is great. it saved may days. by the way, did you use parts from Yamaha exciter? I need your help so that I can tell a yamaha reseller that I can use those parts from Exciter. thank you
As far as i know the XT 250 has the same engine like the SR
At least the 82 model like my SR
Which model is the kickstarter off?
this can be done with the motor installed right. And how much was the assembly
I have a ttr 230 will it work on mine I have all parts order
I need a video showing me how to replace the kick start spindle shaft on a pw80 Yamaha dirt bike 2002 model
Framnces Maddox would like to fit a Kickstart on to my 2005 Yamaha DT 125re would this be a simmer setup ??
Yahmaha r15 s what support the kickstart
Thanks for the video
Hey, I got one more question for you. Around 4:06 you describe that the lever from the kick axle assembly must come up on the stopper. Could you talk on that a little more? I'm not sure I understand what you mean.
Do you know if you can install a kick starter to a 2007 yamaha ttr230? I want to do this but am not sure.
Hello man, G R E A T video, thanks a lot
Just a question, after installing the kick starter, should we consider to reduce the oil amount in engine?
Do you need a battery if you install this?
Old but worth noting, you didnt check the starter freespins, assuming its correct in the stopper position etc and just putting a case back on could cause serious damage, obviously you checked but people may not think of it as it all spins with the clutch basket etc
Hey Al, I'm thinking about converting my 250 as well, did you need a capacitor for more juice?
I haven't tried it but I heard that the 68k uF capacitor works well with the SR250.
Deadly !!!
I HAVE A 1981 YAMAHA SR250 I AM TRYING TO FIND THE WHOLE KICK STARTER ASSEMBLY FOR IT CAN YOU PLEASE PUT A LINK ON THERE WHERE TO ORDER IT FROM
Kick start put the ttr250 right?
What about the XT? Does that exist anywhere?
I really want to buy kick starter of YAMAHA SR 250 So much ! who can help me !
Where did you get your kickstart install kit? Also what did you use for a gasket after you installed the engine case cover?
Hi is it possible to fit this without removing the clutch thanks mike
Que Bueno tengo una moto Sr 250 Yamaha
3:03 I thought you were not meant to reuse circlips, aren't they a single use item like a gasket etc?
Yes, good point. They are cheap, too. In any case, make sure it sits tightly in the groove!
it's all good mate, I was just interested in your thoughts. Thanks for the vids :)
❤️❤️👍
Too bad I S upside down but I got it ! Thanks
Hey man, can I give you ny email or you give me yours? I am trying to install my kickstarter but I'm wondering if I hammered that stopper in too far. It didn't get bent bit it seems like it is in too far for the spring to latch on to it. I have some pictures I'd like to show you to see what you think. Thanks
脚蹬启动
Hi Al. I know u post the parts number here but i contacted Yamaha dealer here in Australia they dont seem to have it. where did you order yours? Thanks
incomplete video
Why bother? Electric start is good enough.