Renault Megane steering lock fault repair.
Vložit
- čas přidán 5. 05. 2016
- Consider to support my channel and all the hard work put into it at / lmautorepairs
Thank you
Hi
In this video I take you through the repair of a Renault Megane steering lock fault.
I have replaced the faulty steering lock with a second hand one, but because this locks are coded to the UCH (Body control module), you can not just straight swap them.
First they need to be blanked, virginized, deprogrammed or whatever you might want to call it, In this video is exactly what I will show you how to do.
A bit of info that I have missed on the video, the tampering safety mechanism can actually de retained, a bit more work, and needs to be done in a certain sequence, if I ever need to do this again, and if I remember, I will make a video show you how...
NOTE THAT THE LINKS BELOW ARE FOR A QUICK REFERENCE ONLY!
FEEL FREE TO DO YOUR OWN RESEARCH PRIOR TO HIT THE "BUY" BUTTON.
Flux used: NC-559-ASM-UV
www.amazon.co.uk/gp/product/B...
To clean: Isopropyl Alcohol
www.amazon.co.uk/gp/product/B...
Fiber Glass Cleaning Pen:
www.amazon.co.uk/gp/product/B...
Soldering Iron: Temperature controlled soldering station.
www.amazon.co.uk/gp/product/B...
Hot Air Gun Station:
www.amazon.co.uk/gp/product/B...
Desoldering Vaccum Station:
www.amazon.co.uk/gp/product/B...
Remote Tester:
www.amazon.co.uk/gp/product/B...
www.amazon.co.uk/gp/product/B...
Uni-T clamp meter:
www.amazon.co.uk/gp/product/B...
EEPROM Adaptor:
www.amazon.co.uk/gp/product/B...
X-PROG:
www.amazon.co.uk/gp/product/B...
Hope you enjoy the video.
Any questions or comments, please put them below.
Like always, thank you for watching! - Auta a dopravní prostředky
Great vid man thanks for sharing. I got my passat b6 steering lock fixed thanks to you.
That's great!
Thank you for watching and for your comment!
I'm mexican, gracias por la clase y el gran tip señor, Dios lo bendiga por compartir sus conocimientos
oi
No necesitas agradecer ... estoy aquí para ayudar!
Much prefer your videos, everything explained in good detail. Thanks
Hi
Thank you for watching and for your comment!
I understand tanks for answer it help's me a lot i dont know a lot of english i'm from romania and for this problem at renault no one helps!all the best for you
Ionut Dascaliuc
No problem... any questions feel free...
Perfect done.. do you have a idea of the metal-bar, who came in and out. it is changeable??
I've got a scenic 2 1.9dci done loads to it already rewired the r2 connections under passenger seat
new rear crank oil seal
2 coils
injector x2
service
But now I have this fault got a kit fro the car but is there any way of bypassing it just to confirm it's the fault?thanks
Sir I am in Oman the problem is here not get renault car part so plz say how can I get car part from were
Does car crank with this fault or not does anything when we press start button coz I got same code on my car df010 , my car cranks but not start , can you advise anything
I have the same problem with my Renault megane2 1.6 16v.
I did change all my car computers including this one and I did program this Eeprom. After I plugged the steering lock module the car started normally I turn it on and off 5 or 6 times without any problem. but when I take the car key out of its reader the same problem came back! I don't understand why. could you help me, please?
Thank you for the very useful video you are making
Renault Fluence 1.5dci 2012 model Steering lock what is the solution
Hi please help, how do I remoce that white thing, its very much stuck in there
Do you maybe know what the code DF1356 engine code mean? For Renault Megane. Thank you!
Hi! Nice video, and very well explained! One question... what if i swap the original eeprom, and move it to the new board? the car actually starts and all, it just doesnt lock the steeringwheel... so i have an mechanical issue more than electronic one...
eXe
Hi
It should work, if the problem is mechanical... if is a corrupt eeprom, you will just be moving the problem across...
Thank you for watching!
Please can I se d you my megane steering lock and how much will you charge to fix it.
Wow. I did not know the bolt only comes out if Steering is in unlock mode !
I obviously snapped it which now causes the lock to be jammed :-(
you a great men, thanks. I have a similar problem, what i can do? i need replace a lock module? can i change only mechanical parts of lock module ? thanks
Eduard Bodrug
If you replace the module with a blank and ready to fit, it is plug and play... otherwise all the info is on the video.
Hope that helps....
Hello, nice video! One question though: couldn't you use a clip cable, so you wouldn't have to desolder the chip ?
Yes.. you can try... I personally prefer to remove it... the pcb circuit can sometimes create issues...
Thank you for watching and for your comment!
Hi pal ...
I have the same issue with my megane, I've change the original with a second one, the car starts one time and that's it...if I will send them to you by post can you fix them???
I'm from Cumbria
Thanks 😊
Hi
Possibly is...
You can also put a new empty eeprom 24c02 and rescue problem, so I solved the problem in that way.
Same thing...
Thank you for watching and for your comment!
Hello sir, I have a question if I buy a second-hand one steering modul and just change the ST24/25xx04 chip only from the old one to the new, it's OK? I have Df055 error Eeprom failed activ. Thank you
mirel m
Probably not... if the eeprom from the lock that is on the car is corrupted, you will be only moving the problem...
You have two options, remove the eeprom from yours and blank it... put it back and see... alternatively you can buy a second hand one, blank the eeprom and that should also work...
thank you for the advice it really assisted me. Do you know of any one who can assist me with that kind of a problem for my Renault. What makes that if I may ask?
Hi
A good Renault specialist, dealer or someone that knows this systems...
Great work mate !
F Norbi
Thank you for watching and for your comment!
Brilliant video. Most informative. I need to buy the eeprom reader and cables ect to perform same tas, do you know were i can get them from. Keep up the good work by the way. 👍
Karl Taylor
Hi
Thank you for watching and for your comment!
You can easily get a programmer on eBay for example...
It all depends how much you want to spend...
lmsvvavr im going shopping NOW lol. Thanks for the help. Much appreciated
Hi I'm having a few issues with the steering module, steering doesn't lock it just clicks.then I try to start the car and it doesn't start I have to lock the car then unlock and try again take s 4 or 5 times.any ideas where to look.
Start by scanning the car..
Thank you for watching and for your comment!
Hello, when you change the dump file to FF do you need to update the checksum, i use beeprog
Soufian Attar
No need to checksum...
Wow job good I love this please can you help me with the problem of renault megane 2000 model the ignition key was broken and I change it now it refuse to start I have try all my best just to measure it start still the problem remains the same please I need some advice and experience from you help me please
Have you transferred the transponder from the old key to the new one?
Thank you for watching and for your comment!
Do you happen to have a pic of the switch on the stalk that stops it winding too far?
Don't think I do... sorry...
Thank you for watching!
Another great video. How did you know the memory was going to be written if you delete it?
Hi
Theoretically I blanked the chip... so when the UCH detected the blank steering lock, just wrote the info again...
If that makes sense...
Thank you for watching and for your comment!
you can read eeprom from OBD2? Renolink i can use for this manipulations with steering lock?
Don't think you can, but I never tried to be fair...
👍👍👍
Hi, i have an issue with a 2006 renault espace steering lock MOT failure, i took the lock off the steering column to see whats wrong because you could turn the steering wheel to the right with card out, is the lock pi inside the problem? i opend it and now the lock pin doesn't go in...
Ta. Tariku
There is usually a small system that engages when the lock is opened, which then prevents the lock to be correctly closed and operational...
Just remove that system...
Thank you for watching!
partner when you left the epron blank is as if it will remain a virgin? Thank you
AstroBoy yo
Hi
Yes it is...
Hey there, I have a basically broken Renault Laguna, very similair steerling lock box, I am taking out of the car what I can still use (I bought a newer Laguna) and then im going to get rid of it but the steering lock is currently locked, I took off the ermm pin module between the steering shaft and the steering wheel, the bit that holds this steeringlockbox on it.
My question is, how can I get it off or how can I just unlock it so I can steer the car, so when they come and get the car, it wont be as much of a hassle?
There is no easy way to remove it if the steering is locked... you need to dig into it, cut or drill the bolts... surely you find a way... perhaps, remove the steering column... Will be easier to work on it when outside...
👍👍👍
@@LMAutoRepairs thanks man, I was afraid of that but it makes sense, ill try to get it off and if not ill make some make shit connector pipe to steer it just to get it on the truck later, thanks again!
The method of erasing details on eeprom is valid for all eeproms in different modules? (Ex: ecu eeprom or sound unit eeprom)
No...
Thank you for watching!
Could you use a new chip which is blank or does it need to be the one from the module ?
What version of Renault CLIP software do you use ?
Superb videos BTW and you make it all look sooo easy.
Arnold Rimmer
Hi
A blank chip should work...
I still using version 160... if I am not mistaken...
Thank you for watching and for your comment!
ok, thanks. I only asked cause the interface looks much better than the new version and I prefer windows XP for all my programming. All the best to you for sharing your videos.
Arnold Rimmer
Win 7 is not bad for most of the stuff... but indeed XP still the way to go in many other softwares...
👍
I had the same problem on a Megane 2 but the real reason it didn't worked was because of poor contact between the steering lock(pin 5) and the fuseboard in the engine compartment on the +12v after ignition. Or poor contact between the engine compartment fuse box and cabin computer same link +12v after ignition. I cleaned them and the 2 related fuses terminals and car works ok for now. Didn't have anything to do with it's 24c04 memory. I don't understand if the guy had problem with the 24c04 memory geting its data altered , why didn't he changed it with a new one? Before starting to blame the steering lock do a can clip diagnostic. Even if it's made by Valeo. it will tell you exactly it's problems. These cars at their age start to develop issues with their connector terminals. Either they corode, oxyde or get burn because of the high contact resistance.
In your case, looks like you had multiple issues...
Thank you for watching and for your comment!
Hi
You was talking about recode the lock, do I understand it this way, after you virginised the lock, it will automatically code the right way first-time you start the car? 🤔
What interface do you use with Canclip, can I use the VCI J2534 from the Autel IM608? 🤔
Instead of de-solder the eeprom, couldn't you just use the clip and read?
that is what i intend to do.but seeing it working, i do nor know what to search for after disassembling. the car is working fine,olny when i forgot to reset the error message it happens.i was planning to buy a second hand locker and use the old controller.
Check that the pin is actually moving all the way...
Look for anything unusual...
hi,can i make the same thing on scenic 2 2004 write with FFFF..?
MrSkimmer06
Never done a scenic... but you always try...
Thank you for watching!
Hello, i'd ask if fuse box's eeprom works the same way. Do you know the no. of eeprom ic. Thanks
Never done on that one... sorry...
👍👍👍
Okey, thanks. I gotta do somehow.
on the lock connector pins 3 and 6 are for the can bus to make the lock operate. do you know how to check them? multimeter or a scope? cheers from Porto
Scope...
Thank you for watching and for your comment!
@@LMAutoRepairs hi thank you very much for the reply. will be diagnosing a bad lock tomorrow and i am doing the homework, i am new to canbus as i work mostly on older cars, will be using an old 20mhz 2 channels analog scope wich i use for my hifi repair hobby, i dont know what signals to expect in the H and L canbus pins but i guess if i see activity when trying to lock/unlock then i can assume the fault is in the lock itself. "potato logic" like we say here
@@MrHBSoftware
Yes... that should be enough...
A quick Google search and you will find loads of samples of can signals...
👍
what is the device that you are using to read the ROM? what is the name?
Hi
In this instance was X-prog...
Thank you for watching!
hi ,nice work for meg 2. what about megane 3 ,does it work the same way for coding the esl., fill all data with FFF. can someone advise please. thanks
jasonics md
Hi
Thank you for watching and for your comment!
Unfortunately I can't help you... I never done a megane 3 nor have researched how to...
Google might be able to help you...
iive tried on google,many forums,it seems no one has done it yet. esl is same as meg 2 with 24c04 eprom. if u get any info let me know friend. meg 2 is 250kbaud meg 3 500kbaud.
Hi everyone, has anyone tried it so far on megane 3?
I had a problem yesterday and tried same way like mk2 but didn't worked. Mechanical part is the same but board is little bit different.. and it's all coated with varnish to make soldering more difficult😭 Luckily, it was a mechanical problem so I swapped out whole board to make it work, but I would like to know if there is a way to virginise it simply like mk2
Thanks in advance
Hi does you clip can be conected to server for reflash and coding online
If you have an an account...
Thank you for watching!
Tank you so much,i like your videos!
MrSkimmer06
Thank you for watching and for your comment!
LM Auto Repairs i did teach many things with yours videos,i hope you will continue!
MrSkimmer06
I will do my best...
Awsome thank you for share to information, elv megane 2❤
☺️
👍👍👍
i didn't disassembled the locker,just took it out and i saw it working - pussing big pin out and in,like it was supposed to do.but mounted on the steering wheel, engine didn't start.also,in day by day, the steering wheel is not locked at all.
Open the lock and inspect...
That would be my next step...
Hello will I be able to virginize the chip using UV light instead of this method using the computer? My Renault megane is doing the exact same thing. I've changed the whole steering lock controller and the car started only once after I've changed the steering lock. Now I understand why it started once thanks to your explanation. So at least I'm a bit motivated now, as I had nearly given up.
Hi
Not sure if possible with UV...
A programmer is quite cheap anyway... you can get one for less than £10...
Thank you for watching and for your comment!
Okay, thanks a million! Please confirm that all I need to do is erase(virginaize) the chip I got from the other megane and then it should help clear the steering lock error?
And I saw you reading the digits engraved on the faulty chip you were replacing, I'm just curious to know where you used that? Is there anywhere I'll need to enter those digits engraved on the faulty chip I'm replacing?
@@thabolegwate4444
The engraved digits are just the identification of the chip... you don't need to insert them anywhere, is just that you know which chip you are working with... so you select the correct chip when to read it...
And yes, should be the only thing you need, providing that there is no other issues with the car...
No there shouldn't be any other issues because it was running perfectly after I changed the engine. The only reason the car won't start now is this steering lock issue. You've been a great help thank you so much, I've been suffering with this issue for months now... Only Lord knows how grateful I am! Can' thank you enough.
@@thabolegwate4444
No worries...
😉
Hi, I tried yesterday to reset and erase 24C04 Eeprom with ICPROG (With hot air solder.... and my Eeprom Programmer with smd/dip adapter) and put it again in my steering lock module but Nothing: Message again Steering Lock Fault
A week ago I bought from UK a new virginised one and put today on my car... Message again Steering Lock Fault..... SO WHAT TO DO NOW?
Patrick Pat
You have a fault elsewhere...
Have you scanned the car?
lmsvvavr I have an OBD little interface but I cannot do if I cannot switch on...
Hi sir, u can use renolink to verginize the EPS
👍👍👍
friend do you repair the megane 2 address columns?
angelo niebles escorcia
Hi
What exactly are you looking for?
Why didn't you simply swap the EEEProm chips or the entire PCB?
Because the idea of this video was to demonstrate how to reutilise the lock...
If the issue with the original lock was mechanical, yes, swapping the eprom or the whole pcb would work...
But this locks can sometimes corrupt the eprom data, which in that case this is the only solution...
Thank you for watching and for your comment!
👍👍👍
my 2004 Renault Megane when I stop the engine, and turn the steering wheel ,I feel clicking like it didn't fully lock and then when I start again the car is fine ,and the clicking goes away and I can just drive back normal ,but it sounds like i need for of these models, where can someone go and get this done ,without having to go to Renault and a crazy money how difficult is it to do what you are doing on the computer or is there a computer?help!!!!
jozzerful2
Hi
You can get a second hand lock and follow the procedure in this video...
If don't have the meanings to do it, the you need to find someone...
Thanks for video. What programmer are you using to write data to chip? Thanks.
If I recall correctly, I used X-prog on this video...
But any other compatible programmer will do it...
👍👍👍
@@LMAutoRepairs Thanks. My friend call me today with the same situation, as on your video... But car just don't want to start on the road.. so we starting to find a quick fix... After a lot of tries he started the engine by manual moving of locking block, and run car to parking... but that was a last chance, after that it finally stopped.
As I understand fastest way to fix it on the road is a cheap chinese steering wheel blocking emulator, because he cant find service, that can help him to fix it
@ukrainian333
Yes...the emulator should do the trick...
👍
hello. i have some kind of the same problem,but my car acts a little bit different.after i press stop button (to stop the car) i receive a mesage of "steering not locked" and a sound like something is hitting the steering column and the steering wheel moves a little bit.if i do not reset the error by pressing one again the stop button,next time whne i try to start,it will not start.only pushed.i have dissmounted the steering lock and it is moving normal. do you have any ideea? thank you and sorry for long post.
Hi
Thank you for watching my video!
By your explanation, your steering lock is not working properly...
You might have missed something when you had it open...
have you open it completely?
Hi friend,how did you knew it/read if you put fff on data then it became a virgin data?can be applied every car or? would like to learn more plz..
I have Audi A8L have same problem can same method u did can be applied??
Hi
Not every car is the same necessarily...
I never did that one, so not sure...
But I would say on an Audi is most likely different...
Thank you for watching!
When I just turn on the ignition, the lock works normally and turns on and off, but when I turn on the car, it just turns off but will not lock when the car is turned off. Lm do you know what it could be
Either a mechanical fault with the lock, or a similar issue as per the video...
Difficult to tell without checking...
Thank you for watching!
@@LMAutoRepairs Thank you
hi
How did you know that the problem exists in steering lock ?
mohamed mohamed
Hi
Experience... this locks are known to be coded to the car and they are part of the immobilizer.. so you can't just replace it with a second hand one... as this will be coded to the car it came from....
Stuck at roadside again :( happend 4 times in the last 5 months the steering wheel says it locked and the workshop do something it starts and the then in a month no go again. Anyone any suggestions?
Hi my friend, I need to read and reset mine. Please let me know which windows program did you use to read and write eeprom and which kind of adapter did you use to put the eeprom inside. Thanks
Patrick Pat
All the answers to your questions are on the video...
X-prog to read and write...
ok, thanks, so is it good an Eeprom GQ-4X device to put the chip on it? and Renault Chip Eeprom is protected or not as you know, I think no, is it?
Patrick Pat
That programmer should work... with the correct adapter...
The eprom is not protected.
Se hizo todo como dice el vídeo, pero después de un rato de estar prendido. Se apagó y no volvió a encender!! 😭😭😭😭😭 Que puede ser!!! Auxilio help me!!!
I've been having trouble starting my car I just hear clicking so I took the module off and the bolt that comes out I use a screwdriver to push in and out a few times and that seems to off done the trick for me anyway..
I would add some lubrication to it...😉
Thank you for watching and for your comment!
@@LMAutoRepairsso would wd40 be OK to spray in where the bolt shots out.. I'm not gonna take it apart
@@andrewbeardsworth5461
Possibly... but I would use silicone based lubricant...👍
Would any silicone spray be OK or a specific kind..
@@andrewbeardsworth5461
Not really... any should do...
i have same problem but when i shaking my steering wheel car start up....so that modul works fine but i think he losing connection or something pls help
Check connections etc...
Thank you for watching!
@@LMAutoRepairs tnx......check jack connection.....can i lubricate that iron who lock and unlock sterring wheel? (sry for bad eng)
@@ipe7739
Yes you can... you can easily remove the lock when on the unlocked position...
@@LMAutoRepairs tnx i will try
hello friend greetings from canary islands, i have a renault megane with the same problem exactly what you recommend me to do, i have a programmer vvdi prog can i do with this team. can you help me thank you very much...... hola amigo gracias
I am pretty sure that vvdi can do it...👍
Thank you for watching and for your comment!
@@LMAutoRepairs hola amigo con el equipo que te comente vvdi si pude hacer la lectura . pero no puse toda la informacion en blanco de el archivo, el coche sigue igual hay que poner el todo el archio en blanco. gracias por tu a tencion
@LM Auto Repairs hello friend with the team that vvdi told you if I could do the reading. but I did not put all the information in the file blank, the car remains the same, the whole file must be left blank. thanks for your attention
hi nice video, but how someone can take out the lock, its only one screew but doesnt come out
Hi
The lock need to be on the unlocked position, in order to come out.
I never had to remove one that was not unlocked, surely I will make a video for it when one comes along...
Thank you !
Thanks!
👍👍👍
Thank you 😊😊😊
Anass Lakraker
No worries... Thank you for watching!
Another ask, Do I need to use at the end also Renault Clip device to reset all or to recode the new Steering Lock or just put the virginised one and push start? I don't want to buy Renault Clip and Software to use only for Renault Cars...
Patrick Pat
Just put it back...
No need clip...
Might need to clear codes, but for that any reader will do...
So, If I buy a new or recoded "Virginised" one from ebay, just to put after i get out mine, and push Start button, it might be work?
As you know, is it possible that there is a bigger problem on the Steering and my car gives the same error on display that is not only an electric problem, that if I buy a virginised one and put it on my car will not work because of it?
I would buy in the future the Can Clip device, I have just the software, as you know, could be good and useful for another car or just only Renault and maybe Nissan motor cars for the future, do you suggest to buy? Now I have only a OBD Elm bluetooth device and Android App like Torque, OBD Doctor, Dash Command that in the specific case doesn't work to reset errors
Patrick Pat
OK, it should work...
Most os the problems with this system is the 'locking mechanism/module'...
So if replace it should fix the problem.
Unless, very unlikely though, that you have a problem with the steering shaft...
Patrick Pat
Clip does only renault...
There is although, some versions of the Consult (Nissan diagnostic tool), that can do both...
If you want a tool do do different cars, then might be better you research a bit more...
Depending on how much you wand to be able to do on cars, and how much you want to spend, there is several options out there...
Hope that helps.
Good job
Thank you for watching!
thanks a lot man
Oltian MUNGA
No worries...
Can you fix mine?
Hi i buy this to replace the faulty stering lock AD-MEM01
tell me how i cant conect to my pc to use please
Ionut Dascaliuc
I am sorry, but I am not familiar with that programmer...
Does it not come with instructions?
i ve just order that product i see when he came!i have another question for you do you have anny ideea if another parts of steering fault repair work on my car if i buy from another car end i do the same thing you do in this video?
Ionut Dascaliuc
ok... your question is a bit confused... but if you buy the whole steering column it will come with a steering lock which you will need to virginize(as per the video...)... Otherwise the steering will not unlock...
Hope that helps...
Do you think it's the UCH problem? But do you think I can buy all ECU UCH Steering Lock and key from other car?
Patrick Pat
Possibly... or a wire problem...
Have the car scanned and go from there...
Hi, What you mean with scanned? you mean with Renault Clip device? No, I have just an OBD ELM interface that doesn't work. Hey, Renault Clip could work or not before you solve problem? Does it communicate via CAN interface also with the problem?
I would like now to check my ECU, 3 Connectors, and also to take out my ECU to open and see if there is oxid somewhere inside, I noticed oxid on the connectors. Another way I want to take is to buy the complete kit: ECU UCH Key and Steering Lock from an other Megan Car, is it a good idea?
Patrick Pat
That will might work, but might not...
If your problem is for example a wire problem, that will obviously is not going to solve your problem.
Scan the car first...
Does not need to be with clip, see a garage, they can scan it...
See if there is something that might point you in some direction...
when finished how do you re- connect the lock back in to the car ?
Yvie Stevenson
What do you mean with connect?
do I have it unlocked or locked when re connecting, how do I plug it back in lol
Yvie Stevenson
I usually close it down and fit it in the unlocked position... but that shouldn't really make a difference...
If the reset is done correctly, the lock will sync with the UCH and that's it...
obrigado. muito bom!!
Alvaro Barreto
Obrigado!
Hey up have the same car and my stearing lock keeps saying not locked would this be the same thing. my car starts just here a little bit of clicking when turning the wheel :-)
Carp Guy2016
Possibly... Unless there is something wrong mechanically inside the locking system...
lmsvvavr thanks for that how much would I be looking at to get fixed thanks
Carp Guy2016
Depends... not all garages are able to do this, and the replacement is often the easiest option.
You can look on eBay for example, and look at the price... usually about £60 reseted. (Same procedure as per the video...)
Please can you fix mine if I post it to you , I can pay up front.
You are my lost hope i did every possible thing but eventually i bought a new one for more then 400euro, but nothing happened. The lock is new from the dealer in box so he was empty. When i push the start/stop button i hear something like an airco and inside my backmirror their is something also like a small motor/ airco making noise. Further i hear when i push the button a ticking noise but i cant but my car on. Everytime i push the button it will turn of and then one , everytime. In the garage they told me that it was the lock so i replaced the lock. My car is in front of my house because i used a cable and a friends car to put him here.
I was wondering if you have any last ideas.
The things he does is.
1 put key inside and pushes button start/stop
2 the car makes ticking noises and breezing air
3 . Then service and steering lock dispears and then when i want to start everything is resetting.
What could it be...
Hi
Have you checked wiring integrity from/to the steering lock?
Scan, any other codes?
Thank you for watching and for your comment!
@@LMAutoRepairs Before i changed the whole unit ( steering lock). i got the following codes.
DF002: Key Colomn, intern electronic defect lock colomn.
DF010:combination circle lever under the handlebar not properly connected
DF009 circuit +APC incoherentie
df 031 , df 027. The garage deleted all except the df 002, that's why i thought i would change the unit. What can i do, because when i try to start the car, with star/stop button. everything is resetting and the airco i hear, and i can't even put my windows up anymore, THE update is after i put on a new unit like your video, it says, electronic malfunction.
Is it possible you could help me, if i make a video?, because the garage and everyone have no idea about the electronic things... I was thinking when i try to start the car i hear clicking and i believe that are they fuses, but the garage told me he checked them. i have no idea what to do.. thank you my friend
czcams.com/video/e83EbZI4Wlg/video.html , i made a video
Hello Brother tell me how to use this tool Xprog
There no simple way to explain it... whatch my other videos on it, and do some research...
The main bit is the connections really...
👍👍👍
well done big up
Thanks!
Hello my friend
I wonder an explanation of inertia switch operator fiat doblo 1.6 diesel 2015
My fiat makes an accident the engine will not start and warning lights flashing
I do a diagnosis by autocom the fault code is U 0427 Inertia function : present
What the solution about this
Med téchnicien
Hi
The car been involved in some sort of accident, correct?
There is a procedure to be followed to allow the engine to be restarted...
Something along these lines:
turn ignition key to MAR;
* turn on right turn signal;
* turn off right turn signal;
* turn on left turn signal;
* turn off left turn signal;
* turn on right turn signal;
* turn off right turn signal;
* turn on left turn signal;
* turn off left turn signal;
* turn ignition key to STOP.
whats the name of the program that you used to erase the data FFFFFF's ? give me a link to downlaod it pls!!
Touil Abdelghani
I have used the editor from the actually x-prog (the programmer)...
That comes with the unit... any other programmer will surely come with its own editor...
partner leaving blank fff memory then can be mounted?
Hi
Not sure if I understand your question...
But u would say yes... blank the chip, put it back, connect and turn ignition on...
Thank you for watching!
@@LMAutoRepairs traducir a español pliss
Why don't you translate?
Copy and paste....
Hi Louis Thanks for sharing your work, I want to ask if this way with( FF) fit for clio 3 year 2012 i have the same probleme
@@abdoudfi8205
Never tried or researched... but you can try and let us know...😉
Thank you for watching and for your comment!
My car Saab9-3 got the same problem and I wanna rest the fault code! You know how can I know which eeprom should I choose? There is no information on internet!
Valeo SCL modules name name. Tnx for your time 🙌
The might be a completely different procedure...
I never had to do one on a Saab, so can't really advise...
@@LMAutoRepairs Tnx for reply! So u mean there is no way to know which eeprom is correct even from Ecu.
No... that is not what I said...
If you open the module, you can relatively easily identify the different components...
What I said is, the reset of the eeprom most likely is not done the same way as the one on this video...
You can always try, but I have doubts that it will work...
What is the issue you are having any way?
@@LMAutoRepairs unfortunately I can not share any picture or video here I could show you! Streering wheel lock fault dosen't let's car start?
@rmt5820
OK... but that doesn't necessarily means you have the same issue...
The electronic steering locks, have little motors and microswitches that can fail...
So, though you might have the same symptoms, doesn't mean you have the same problem...
You need to start by scanning the car, look at live data to see if anything points into any direction...
Hi
Can I use bdm 100 to read the rom and reprogram it again ?
Hi
I don't think bdm100 can read this eeprom... only mpc555...
LM Auto Repairs I found in the description of bdm 100 that it reads the software for the following
29BL802 SSOP eprom file (or ROM memory with maps if eprom physically not present);
MOTOROLA MPC5xx Processor file;
Serial Eprom content.
So can it be used or not?
@@ahmedesmat6137
You have not researched enough...
29bl802 is a flash memory...
Mpc555 or similar is a MPC...
The memory I am reading from this steering lock is completely different...
Research more and you will see that bdm100 will not be much of a help in this case..
LM Auto Repairs
Will please tell me what are the alternative for xprog to reprogram it ?
@@ahmedesmat6137
Any eprom programmer... there is many out there...
Willem, orange, xhorse, and the list goes on...
thanks
Krystian Straus
Thank you!
Thanks man
☺️
👍👍👍
Hey awesome tutorial. Where can I order the chip reader from please
solpex
Hi
There is several online places... eBay is a good starting point...
Thanks for the reply mate, eeprom read right ?
solpex
Read and write... yes...
Thanks bro
Private message me a cheap one if you can place mate they are pricey
Hello, what is the procedure for resetting the locker to unlock, before I remove it from another vehicle? Do you know anything about it?
Thank you for the video!
Very useful :))
Not really sure... if renolink can do anything to it... this is the only procedure I am aware of... but I will try next time I have one around...
Thank you for watching!
LM Auto Repairs the first part of the issue is that I can’t separate it from the steering wheel assembly. It’s locked. I can’t extract the screw.
Can you help me please?
Thank you:)
Is there a video to see how it all off? How do I get this part? And how does this part is called to be purchased? Thanks, man.
Bili Kid
Hi
It might be a video on how to take it out, I never captured it due to how simple it is.
You have one bolt and one plug... that's it.
This part is the steering lock.
Search for "renault megane steering lock " and you will find it.
EBay is a good place...
Thank you very much. Can you just say, if you buy a new part that you have to decode it before installation? Have a nice day.
Bili Kid
If you buy it brand new, it is plug and play.
On eBay, for example, you will see that there is sellers selling them already reset and ready to fit.
thank you for ansower
Med téchnicien
No worries...
did you delete the white plastic?
Cerrajería Security
The anti tamper pin?
Yes I did...
Thank you for watching!
nice jobe
Alli Osm
Thank you!
Can this same technique be applied to the steering ecu ?
for a clio 3 that is.... I plan to pull the dump over the next day or two :)
Mike Jones
Hi
Possibly... I never done one of those...
Ive found a couple of dumps for the clio 3 but once in the hex editor they look nothing like yours ..
Hello :)
Mike Jones
They don't need to... each car is different... even on different megane the data would be different... That's why they are not interchangeable... each lock contains the data that locks the steering lock to that car....
the moment of troth nice job ooookkkkkk
😊
👍👍👍
What year is this Megan?
2004 if I recall correctly...
👍👍👍
You can replac it !? or u need to copy cods to the new one.
i-Bird
The replacement needs to either be blanked of contents copied from the original one...
Ok ! thank you bro
i-Bird
No worries...
Ok .How can i help my self if this problem come in desert & the car wont started!
i-Bird
Well... you still need to remove the steering lock and do whatever...
If the steering lock is locked and won't unlock, it is a bit tricky to remove it, but can be done...
will it be OK to just unplug and plug back in
canyouseewhaticansee
Depends on what the problem is...
lmsvvavr when I first got the car steering lock worked a couple of times drove no problems. last week constant L E D and stop sign on dash won't start there is a click from the reader when you press the button to start then nothing .
I've done the fuses cleaned no water damage + ecu good new 6 months ago +battery good + all connections good live + earth cleaned put back.
going to have a look at the key card module not sure if it's anything to do with that .
so with the steering look worn now do I unplug and put back.
thanks
canyouseewhaticansee
If is the steering lock that is causing that, it is logged in the UCH...
Hi, before thanks a lot about recording this video.!!
I want to ask you about if is posible to buy a new one unit of 24c04 eprom (maybe this unit came erased in FFFFFFF all)
My problem is the next:
2 years ago have a problem wiht this. my solution was go to a scrapping cars and take a used unit.
After i changed the circuit board from my car to the steering lock that i buyed.
2 weeks ago i had the same problem and i made the same thing, 1 week ago, i have again the message of blocked steering.
I tried again buying the used steering, but now i cant make it works.
So what i should to make now. I was thinking about to buy a new one 24c04 and replace it, but i dont know if it is possible, or is mandatory to use the old 24c04 epprom from the steering circuit of the car??.
Thanks a lot.!
F.A. M
Hi
Thank you for watching and for your comment!
A brand new eprom should come empty... so should work...
Do you have a programmer, to read and write chips?
i ask you this because i have not a programmer to write chips, and i was thinking to buy only the eeprom and change it. If it was not posible i will have to buy the programmer and try like you.
I ask you because o didnt know if the eeprom has more information inside like a Vin code or other.
Is it work are you try to replace 24c04 with new one
F.A. M
I really apologise... only saw you message now...
A new EEPROM should come empty a filled with FFFF... but not necessarily...
Ask the seller of he can do it before send it to you...
Hello i tried with new one it doesnt work for me.
can u bypass the system?
Chris Jenkins
Hi
If there is a way, I am not aware of... never even looked for.
Do some research and see if you can find something...
Help me
السلام عليكم