Manitowoc water level probe troubleshooting
Vložit
- čas přidán 21. 08. 2024
- Manitowoc ice machine not working properly. Water was over flowing the water trough during the fill cycle. Removed and tested the water level probe.
If you found this video helpful please consider supporting the channel on Patreon.
www.patreon.co...
I recently started working for an ice machine company in OR. I don't have much experience with this stuff, but I am learning as much as possible, and your videos are very helpful. My goal is to become a full fledged tech at some point, so I am very grateful for all of the info you put out. Thank you.
Awesome bro! I was in your shoes about 4 years ago. Keep learning and watching videos. You’ll be a full fledged technician sooner than you know.
Im about to binge watch your videos, thanks for sharing. Interested in learning more about this service
I do all ice, all day. I’m hoping to make many many more.
Always looking forward to your videos. I learn a lot. This water trey episode is one of the best
They’re getting better right?
Yes
I’ve been switching out water fill valves, now I feel dumb. Thanks Dawg!
lol
Nice video and thank you for show us how to check stuff.
You’re welcome!
🇺🇸❄️💪👍 great informative video
✨ 💎
Thank you 🙏 for sharing great to know
You’re welcome again!
👍🤘☝️
💪🤛🛠️
Our companies brand new, maybe a month old Manitowok ice machine has been having the issue of water trough overflowing constantly, however water probes have been switched out and hasn’t made a difference, it’s sort of intermittent, we had a second machine brand new sitting on the shelf so we hooked that one up and it is having the same issue… could it be a water issue? Maybe not enough minerals in the water to consistently cause the probe to ground out like it’s supposed to?
Sounds like you’re on the right track. The water needs a minimum TDS for the probes to properly sense the water. There’s a jumper on the board that is used to increase the sensitivity of the probes. If you haven’t already I’d recommend calling Manitowoc tech support. They’ll help you out with your problem.
@@IceMachine411 interesting we will look into it thanks!
My Koolair ice machine water pump it runs and stop .can it be switch float
Im not sure exactly what you’re asking.
Good video ! Subbed. Liked. I just got a video call from a customer - ice o matic ice0600HA4 water curtain drops into the bin when it harvests. Lol 😂 never seen that one before I think. Gotta go check it out.
I’ve been watching your videos for a while now. You’re pretty awesome.
Sometimes the ice will double slab and the large block of ice knocks the damper off. It could be anything though. lol. Good luck.
@@IceMachine411 Thanks For the Compliment. I Appreciate it. You Look like You know your stuff too. Happy New Year, I Hope it’s a Good one. Thanks for the info / tip too. We shall see. Going to be interesting. 🤔
Ok I'm having this problem ... I pulled the part here in video and test mine I got tone on all probes but still have this issue with thick ice drops . Any advice would be helpful
Watch the video about the ice thickness probe. Might be the ice thickness probe that is giving you trouble.
czcams.com/video/na-q5cW4IW0/video.htmlsi=AR5N37ynMXvJf7xS
Your probe is probably good. May just need to be adjusted. That is unless the ice doesn’t fall during harvest. Then you’d have a different problem. Maybe a curtain switch issue?
id0906a-261 harvest sequence when does water go over evap right away when turned on?
I’m not sure exactly what you’re asking but the sequence of operations are usually posted on the inside of the front panel. Refer to that and it should tell you when there should be water flowing over your evap.
@@IceMachine411 i think i figured it out the lcd shos water level high and low ...both hread high. gonna replace level sensor.
Hope that fixes the problem!
Sir toking you Hindi dubbed please 🥺
I’m not sure how but I will look into it.