![Ice Machine 411](/img/default-banner.jpg)
- 71
- 216 181
Ice Machine 411
Registrace 16. 01. 2021
I work on ice machines pretty much every day. I created this channel to share some of the jobs I do and try to pass on some of the knowledge I’ve gathered. I’m constantly learning and growing as a tech and I apologize in advance if I make a mistake or lead you down the wrong path. I hope you enjoy the content.
Feel free to support the channel by clicking the Patreon link below.
You can also email me at icemachine411@gmail.com
Feel free to support the channel by clicking the Patreon link below.
You can also email me at icemachine411@gmail.com
Manitowoc Neo model UDF0140 Harvest/Hot Gas Valve replacement
This video shows the process of repairing a Manitowoc ice machine that is not working. This ice machines model number is UDF0140. This Manitowoc ice machine is sometimes referred to as an Under Counter Ice Machine or a Neo ice machine. This under counter ice machine had a bad Harvest Valve. The Harvest Valve is sometimes called a Hot Gas Valve. In this video I show the complete process of replacing the Harvest Valve.
Please consider supporting the channel through Patreon. www.patreon.com/Icemachine411?
Please consider supporting the channel through Patreon. www.patreon.com/Icemachine411?
zhlédnutí: 634
Video
Manitowoc IY1474C control board, low pressure switch, touch pad and ice thickness probe replacement
zhlédnutí 438Před dnem
Manitowoc ice machine repair. This machine was not making any ice. I replaced the ice thickness probe, control board, touch pad and low pressure control on this Manitowoc ice machine. After completing the repair the ice machine now makes ice. Viper WetRag amzn.to/4d46lU9
Scotsman ice machine gets hot and keeps shutting off on Code 1 and Code 2
zhlédnutí 636Před 21 dnem
This Scotsman ice machine has a bad fan cycle switch. The fan cycle switch is supposed to turn the condenser fan motor on and off as needed but wasn’t working properly. After troubleshooting the problem it was pretty obvious that the fan needed to be replaced. This video simply shows how to determine if the fan cycle switch is bad or the fan motor is bad.
Ice-O-Matic ice machine fan not working and flashing red light
zhlédnutí 657Před měsícem
Piggyback Spade Connectors amzn.to/4cg7LL1 Alligator Clips amzn.to/4bjTBas This ice-o-matic ice machine kept shutting off. The fan was not working. The machine would over heat and shut off. There was a flashing red light in the front. After troubleshooting it and talk to iceomatic tech support I found the the fan cycle switch was not working properly. I fixed this iceomatic ice machine by bypas...
How to clean an Icetro ice machine
zhlédnutí 451Před měsícem
Ice machine Sanitizer amzn.to/42tf1PA Ice machine cleaner amzn.to/48wyu3u This was my first time cleaning an Icetro ice machine. I followed the instructions in the Icetro technician’s handbook. While cleaning this Icetro ice machine I ran into a small problem with removing the water pump but I was able to figure it out after contacting Icetro tech support.
Manitowoc ice machine low pressure cutout switch not working and bad control board
zhlédnutí 522Před měsícem
Working on a Manitowoc ice machine Model #IY1474C-161. This machine shut off on Safety #2 Long Harvest. After clearing the alert I completed some diagnostics on the ice machine and found that it had multiple problems….
Hoshizaki condenser fan motor replacement
zhlédnutí 480Před měsícem
Last week I diagnosed this Hoshizaki ice machine as having a bad condenser fan motor. This week I returned with the replacement fan motor. This video shows the process of replacing the condenser fan motor on this Hoshizaki ice machine.
Hoshizaki ice machine with a bad condenser fan motor
zhlédnutí 422Před měsícem
Went on a weekend service call for a Hoshizaki ice machine that wasn’t working. It makes ice sometimes but isn’t consistent. Went through some troubleshooting and found that one of the condenser fan motors had gone out. The fan motor will be replaced by the customer and the machine will start working again.
Manitowoc ice machine not turning on - Power button trouble shooting and repair
zhlédnutí 1,2KPřed měsícem
This under counter Manitowoc ice machine wasn’t turning on. Pressing the power button wouldn’t turn the machine on like it should. After troubleshooting the power button I determined it was bad and needed to be replaced. I should the process of replacing the power button and fixing this ice machine. This manitowoc ice machine is also known as a Neo.
Scotsman Flaker ice machine code 2 and making a loud grinding noise
zhlédnutí 524Před měsícem
Troubleshooting this Scotsman flaker ice machine Model #F1222A. The customer called in to say that their ice machine was making a loud noise and making any ice. I found that the top bearing had failed and the Auger was grinding against the Evaporator.
Manitowoc SMS050A under counter ice machine troubleshooting
zhlédnutí 408Před 2 měsíci
This Manitowoc SMS050 ice machine came into my shop because it wasn’t making ice. After some quick troubleshooting I found that the spray nozzles weren’t working properly. They were clogged with scale and needed to be cleaned out. The water inlet valve was giving me trouble as-well. The water wasn’t filling the water tray fast enough. We’ll end up replacing the water valve.
Avantco ice machine troubleshooting and repair
zhlédnutí 1,8KPřed 2 měsíci
I received this Avantco ice machine as a gift and it wasn’t working when I received it. I went through some troubleshooting procedures to determine why this Avantco ice machine wasn’t working. Found out there were three different problems. I fixed a refrigerant charge issue, a drain plug problem and a curtain switch malfunction. This Avantco ice machine is now up and running and making ice.
Ice-O-Matic ice machine troubleshooting - red light flashing and not getting any water
zhlédnutí 2,9KPřed 2 měsíci
This Ice-O-Matic ice machine was not making any ice. The red light was flashing 3 times. This means the ice machine experienced either a long freeze error or a long harvest error. I reset the machine by pressing both the clean button and the power button in for 6 seconds. After troubleshooting this iceomatic ice machine I found the float housing to be malfunctioning. I replaced the float housin...
Scotsman Prodigy ice machine cleaning and sanitizing process
zhlédnutí 1,1KPřed 2 měsíci
Scotsman Prodigy ice machine cleaning and sanitizing process
Hoshizaki not making ice - intermittent mechanical bin control failure
zhlédnutí 777Před 2 měsíci
Hoshizaki not making ice - intermittent mechanical bin control failure
Hoshizaki ice machine troubleshooting - 7 beep alarm
zhlédnutí 994Před 2 měsíci
Hoshizaki ice machine troubleshooting - 7 beep alarm
Scotsman under counter ice machine cleaning
zhlédnutí 2,4KPřed 3 měsíci
Scotsman under counter ice machine cleaning
Scotsman CU50 ice machine troubleshooting - bad control board
zhlédnutí 663Před 3 měsíci
Scotsman CU50 ice machine troubleshooting - bad control board
How to clean a Manitowoc ice machine - step by step instructions
zhlédnutí 6KPřed 3 měsíci
How to clean a Manitowoc ice machine - step by step instructions
Koolaire ice machine making thick ice - intermittent water float issue
zhlédnutí 1,6KPřed 3 měsíci
Koolaire ice machine making thick ice - intermittent water float issue
Hoshizaki ice machine cleaning - so bad it stopped making ice
zhlédnutí 1,3KPřed 3 měsíci
Hoshizaki ice machine cleaning - so bad it stopped making ice
Manitowoc ice machine making thick ice and how to fix it
zhlédnutí 2,5KPřed 3 měsíci
Manitowoc ice machine making thick ice and how to fix it
Manitowoc saved by 16 year old compressor
zhlédnutí 2,1KPřed 3 měsíci
Manitowoc saved by 16 year old compressor
E5 HPC fault Manitowoc ice machine troubleshooting and repair
zhlédnutí 2,4KPřed 3 měsíci
E5 HPC fault Manitowoc ice machine troubleshooting and repair
Manitowoc ice machine troubleshooting - compressor not starting
zhlédnutí 896Před 4 měsíci
Manitowoc ice machine troubleshooting - compressor not starting
Do THIS to fix a Manitowoc ice machine not getting water
zhlédnutí 3,4KPřed 4 měsíci
Do THIS to fix a Manitowoc ice machine not getting water
Easy Manitowoc ice machine troubleshooting
zhlédnutí 1,9KPřed 4 měsíci
Easy Manitowoc ice machine troubleshooting
Hoshizaki ice machine TXV and Mechanical seal repair
zhlédnutí 1KPřed 4 měsíci
Hoshizaki ice machine TXV and Mechanical seal repair
Im about to do this same job today. Awesome video, I will try removing the line. that's a good idea. Thanks for the video
Why doesn't manitowoc just have a schrader install on the high pressure switch?.
How about showing the actual installment of the water pump. I can’t get one in. I took the O ring off and it goes in, but just barely. It does feel like there is enough room for the O ring to be on and go in. Very very tight. FYI 30 years plumbing experience.
Good job thank you for the excellent instructions.
You’re welcome. Thank you for your excellent comment.
That 280 volts probably messed up alot of the electrical components. Would not be surprised if other issues arise
You’re probably right. It took out the pump for sure. I was kinda surprised that the machine came on at all considering the high voltage.
@@IceMachine411 yup. Electricity does some funny things
Do you have Instagram or TikTok? Just subbed, it's been a good minute since I worked on a Hoshi. That float switch according to hoshizaki should be all the way down from factory
Not at the moment. I’ll be starting one soon though.
@IceMachine411 hope to see it soon, I have questions that come every now and then. I don't work on ice makers as much as I use too
Never actually seen one done, this will be helpful. Got a Blueair to do and they are almost identical
Blue Air is from South Korea I think. 🤔. They do look exactly like a Hoshizaki. I hope you plan to make a video!
Very nice…..
Thanks
Hi! Can you make a video for the temperature sensor replacement?
I will if I get a chance. It’s pretty easy to do. Accessing the probe will probably be the hardest part.
Mine is brand new same issue?
Make sure it’s not an install issue. Then call Manitowoc. They’ll take care of you under warranty. They’re awesome people.
👍👍👍
💪🛠️
your new name, The IceMan
Im one of many IceMen out here fighting the good fight. Raise a 🧊 in the air for the Techs out there battling the Ice Machine Army.
Great video. Thank you for sharing
Thanks Kenzy!
Good morning, where I can contact with you buddy?
My friend! Icemachine411@gmail.com
Hot gas valve same as txv? I ask cause the new job i start this week deals with ice makers sometimes
No , two different components.
No. TXV’s meter the flow of refrigerant into the Evaporator so that ice can be form. The Hot Gas valve allows hot gas refrigerant to enter the Evaporator so the ice can slide off the evaporator after it freezes.
Good work tech
Thank you Silent Tech.
Dude! Your video saved me a lot of time. The pump kept losing prime. I could fill the tray until it primed each time the machine went into freeze. The impeller was barely spinning. Thanks!
So happy to have been helpful. I’m glad you were able to figure it out and saved some time. When those pumps start to run slow it can be kinda tricky to catch.
Great video I’m always learning something new 👍🏻👍🏻
Thank you. Glad you enjoyed the video.
How do you take calcium buildup inside the water hoses? Thanks for the video.
I use a pipe brush. For the 1/4 inch hoses I use a pipe brush with the bristles cut off so that it’ll fit in the small hole.
Excellent, thanks for making this video. This is our exact machine. About twice a year, it gets black particles in the ice. Now I know what to do for sure. Here I go, doing it right now.
You’re welcome. I glad you found it helpful. Hope all goes smoothly with your cleaning.
See those exactly like that alot with the newer ecm motors. Older units they just fail open. At minimum, Pinch just below the switch and cut off the switch and braze shut. Install service tee on high side, install flare nut on new switch and install. (Loosen schrader just enough the get pressure to switch) And in a year do it all over again when the new one burns up. Or install a adjustable fan cycle control, set it and forget it. Or best, recover refrig remove switch, install 1/4" shrader and install adjistable fan control, oem filter then do your pressure test and evac and weigh charge. That way you fixed the problem "hopefully permanently", confirmed charge is correct. I did a stupid short video on using a pinch off tool and tool to open the pipe back up, but it leaves the pipe extremely vulnerable to breaking.
Love your advice! Your method is definitely a solid method to complete this job. I’ve always been a little hesitant about pinching the copper but I’ve never had a problem with doing it that way. The comments left on this video were pretty hateful. Apparently there’s a lot of people who think this is a terrible idea. Honestly I’m just following Manitowocs guidance on completing this repair. Hope you enjoyed your weekend. Hope you have a smooth week. Stay safe out there. 💪🛠️
My unit freezes but won’t go into harvest Could a bad prob be the reason why it won’t go into harvest , low float light never comes on
Sounds like you’ve figured it out. The low water float is what sends the machine into harvest.
Great video work. Can we get extended versions though for someone a bit more unfamiliar. My scotsmans are in awkward spots so would love to see the full breakdown of how you took parts off or got to certain areas
When I get a chance I’ll try to make a more detailed version of this video.
Great video work. Can we get extended versions though for someone a bit more unfamiliar. My scotsmans are in awkward spots so would love to see the full breakdown of how you took parts off or got to certain areas
When I get a chance I’ll try to make a more detailed version of this video.
@@IceMachine411 checked another one of your videos and it was from 2 months ago. You did an even better job and gave more details. You might not realize how many people you are helping. You explain things very clearly so much appreciated for your work and due diligence
Really!! Sorry i dont agree with your procedure!
I know it seems strange but this is the procedure given by the Manufacturer. If they hadn’t told me to do it I would 100% with you.
Call the manufacturer , I'm sure you know better than the people who designed the system and defined the procedure .
How can you seal a metal pipe by pinching it?
Pinching the line just stops the refrigerant from flowing out. Welding it is what seals the line.
@@IceMachine411 Yeah, sorry. I phrased it poorly. How can the pinching stop the stuff inside and then releasing it opens it? I didn't know it's possible with a metal pipe.
I think it’s because it’s copper. Copper is softer and more malleable.
@@IceMachine411 Cool!
so, that does damage the pipe you pinched??
Yeah, that looked less than great… but I’m no fridgy.
He applies a little heat then uses channel loks to open that pinch back up
I assume it’s possible if not done correctly. I have not seen one damaged by using this procedure.
Thank you. This video was so helpful.
Glad it was helpful!
Thank you so much. I didn't come to our restaurant, so I turned on the main switch and waited, and it came out a little bit, but I wonder if it's going to take a long time
Only time will tell. Hopefully it starts working!
Ate you purging air and nitrogen ?
Neither. H pinched it. So it was still charged.
@@user-de3cm9lf8oYou can pinch a copper line?
Purged the air out of the line. Didn’t use nitrogen. Would have if I could have.
When you restore pressure to that switch you’ll hear a click.
I guess I should pay more attention. I’ve not been listening.
Good fix tech
Thank you!
Holy shit!! Nice!!!
Right on! 👍
I have one that will run if you put it in test mode via the control board but the touchpad does not respond. Not lights or anything. Is the touchpad a common failure with these units?
Fairly common. I’ve replaced a few recently. Unfortunately they come as an assembly. Have to by the door frame. Can’t get the touch pad by itself.
@@IceMachine411I see. Thanks!
Obviously r 404 grab the orange jug and let’s go
I have the same one, water is not freezing.
That’s not good. Check to see if your harvest valve is stuck open. That’s a common problem with these machines.
I’ve been battling with a 20 yr old large Manitowoc ice machine for two yrs…. I’m almost sure it a harvest valve now…. Great video thank you for the education….!
Pretty cool that you have a machine that’s 20 years old and is still working.
lol same, q series! Gave it a little knock and, wallah! Harvested ice😅
Working on a machine just like that. A big pain in the butt. 😂😂😂. Thanks for the information Man. Good video.
Right on bro. Glad you found it helpful.
My dude !!!!! End up being water filter 😮
Nice! Glad it was an easy fix!
What causes this ? i have a hoshizaki 900 scalloped ice machine , and the plates done this ,it is only 3 years old . I had a icomatic 500lb i never did anything but clean it , i got rid of it because the ice clogged my fountain drink machine , and i needed a little more capacity .
The welds slowly break over time through the freeze/thaw process. Every once in a while you can just get a bad machine. Hoshizaki covers repairs under warranty for up to three years. You can also get the part only up to 5 years. I’d contact hoshizaki tech support and see what they can do for you.
Bro maintvoc ice machine doesn’t produce ice and the machine frequently turns to off mode then we have to switch it on again… after sometime it goes back to off mode? Any suggestions
Without being there in person to look at your machine I’d have a difficult time trying to figure out your problem. Call Manitowoc and talk to one of them. They can help you out over the phone. Manitowoc Technical Support: Phone: 800-247-4520
How does this Avantco determine when to harvest?
I think it’s the water float. When there’s no more water in the trough it gos into harvest.
@@IceMachine411 I tracked down the manual online and it would seem to be time based after evap reaches 32F. I presume this as the adjustment on the "digital" thickness adjustment equals "+/-90 seconds to freeze cycle". I'm not sure if I trust that method.
You’re right. Sorry for the bad information. Idk what I was thinking.
Great video thanks
Thanks
I need to replace a CME unit that's seen better days. I'm comparing this and the Manitowoc cuber. This appears to be a 22" Hoshi and seems remarkably less cramped and faster to clean than the wider 30" Mani you cleaned in your other video. I know you edit, but the Mani video it twice as long and your busting your knuckles to remove parts. Is that Hoshi much easier to clean and service than the Mani?
The Manitowoc is easier for me to clean. They take about the same amount of time. Really just comes down to preference. Hoshizaki ice machines use a ton of water.
Same model machine 2 pic issue. One machine power button lights is slightly blow color no dark and water no coming.second machine pad area power is coming press on button water is not coming
The best thing for you to do is call Manitowoc Tech Support. They will be able to help you out. Phone: 800-247-4520
Great vid. Which water filter brand are u using? Will it work for a KM 901
It’s an Everpure filter I believe. You may want a filter with a higher capacity.
How do you get rid of Both power light Red and clean cycle Red ?
Press and hold both buttons for 6 seconds. If it doesn’t work then try the same thing but use the buttons on the control board.
Adjustments for water control in unit ice maker
I’ll have to look into that.
What kind of witchcraft is that?😂 you absolutely did some majic👍
Abra kadbra. Ha. Welding copper to stainless steel is tough. I’m not skilled enough to weld it in place. One day though….
@@IceMachine411 as muford majic words.. a la peanut butter and sandwiches.. poof!🌈💥
Great video. Thank you for sharing
You’re welcome. Glad you enjoyed it. I’m about to make a video on an ice machine called MAXX Ice.