Generator Governor Adjustment
Vložit
- čas přidán 5. 09. 2024
- Quick and simple tutorial about adjusting the governor of a generator.
Unit used for demonstration: Honda EP 1800 GX 160 Generator
BGM:
Prophet 7 - Noir Et Blanc Vie
Thank you very much and God bless.
#andredraftproject #honda #gx160 #engine #governor #adjustment #adjusting #spring #surge #idle #stable
Had a new carb and fuel tank. This solved the problem!!
Thank you for this video. This is the simplest and well presented set of instructions. Good work.
Thank you very much!
Simple,easy,professional!
Thanks a lot bro!
Thank you very much!
Excelente video, simple, and straight to the point...
Thank you very much!
Thankyou for your help and God bless 💯❤️🇵🇬🇵🇬
Mine doesn’t surge anymore but it idles super high … even on low
Did you fix it? I’m about to go back out and mess with it but it wants to red super high
@@bowtiebuildingdid you fix it lol I have the same problem I changed out the carburetor
@@lorenzomaldonado853 my problem was, somehow, the throttle was stuck in WOT. There’s a spring that brings it back into normal low throttle that wasn’t working. Now it will run normal but only for a few seconds.
Hello, my onan microlite 2.8k stays in open throttle. It wont start unless i manually close it. Then if i release it, it will go full open throttle again and shit off. Any help will be appreciated
I watched this video then went to go do it myself and I messed it up to the point where when I took it off the choke it reved to the moon but I came back later and re-watch watched it and I payed more attention and now it worked lol great vid
Well done couch.fixed my pump.
Very straight to the point. Thank you for the help.
Thank you very much!
Very simple, fast an accurate. Very nice video.
Thank you very much!
Thank you very much engineer ❤ love the explanation
Simple effective and practical, thank you!
Thank you very much!
My generator start running but shut off by itself, does not acelerate, and that part is like stuck, do you think thats the cause , maybe I need to adjust that part?
Merhaba.benim bu kol kendi kendine gaz veriyor ve ileri geri gidip duruyor sorun karbüratörden mi yoksa bu kol mu ?
Do you know what the difference is between the 1 and 2 spring positions on the governor arm I have also seen them stamped H and L
Thanks very much!
Thank you very much too!
my gx200 has another spring that connects to the governors lever; only Im not sure on the other side if or where it connects to the speed control lever..other engines seem to be different
Thanks
Thanks mate you save my day
Thanks! Glad to hear
Nice simple, correct video !
Thank you!
You have to take off the damn fuel tank to get to the governor. Then to remove a bolt holding the fuel tank in, you have to remove the damn throttle assembly. Then there's a giant gap between the back flywheel cover where bolts can randomly fall in if you're not careful. Horrendous design. But thanks for video. It worked in the end.
Yeah, it's pretty hassle to do.
Thanks man!
Thanks..ill try this on my generator for it is super high on rpm making lots of backfire
Hope it helps. Thank you and take care.
❤❤
But after adjusted the governor to the normal place but what can be the causes if the governor doesn't return closed to the carburetor during the on speed and it always consume fuell when the engin governor function in that way especially 3000gen, 2900,8000 8800, 8990gen
it worked!
Glad to hear! Thank you and take care.
In my generator pcb item doesn't work
What i can do ?
I would like to ask if this will work or same procedure on 1000W common small generator? Because I have problem with mine. After cleaning the carb, maybe I accidentally hit that thing when I turned back the carb. And the result, super high rpm with over voltage. I tried to adjust the screw but it didn't work. I think, that governor is the problem? Please help me.
If the carburetor has some springs, have you checked it if it is correctly placed? Try to double check the screw adjustments. Perhaps something opens the throttle as a result of higher rpm.
About the governor adjustment, yes you can try but before you do it, put some markings so you can go back to the previous adjustment if the new setting didn't work.
Where can I buy governor spring from p3 power generator
I tried this last night and my bike took off so fast it broke the cableholding it to a pole. Idk what i did wrong yet
Am electrician said i needed to adjust my governor, hence my watching videos trying to identify, but what does this do?
It alows higher rpm, meaning the engine can run at faster speeds. That's why go karts and dortbimes with these engines almost always have no govenors
So before the adjustment the throttle was stuck wide open ? Just making sure
Yes
Did you try it did it work
How do you know when to adjust it
If the idle changes or became unstable, try checking it and readjust it. That could simply fix the problem.
Ok thank you
@@BradyHocking Thank you too
Gernter repair kia head aur block repair kia pr start kick 5 baar pr hota aur kbi smoke start me deta hy kya waja hy?
What about the Philips head screw with the spring around it, what do you do there.
That is for the high speed setting. You adjust it when the generator is running. If you tighten, it increases more idle speed when the throttle is wide open. If loosen, it decreases idle speed.
@@DraftProject Ok thanks that what I want just a bit more revs at full speed.
Will this work for a Robin Subaru EX13 engine on a Coleman Powermate1800 Pulse EX?
I have never encountered that engine before. But probably yes. Most of these engines are similar. You can try small adjustments to see if it works.
@@DraftProject Your procedure worked perfect on the Robin EX 13, on our Coleman 1800w generator. It was off a few degrees. It now holds 60hz (3600 RPM) , where before it would race up to 72hz. thanks so much!
Good
Thank you!
Drop the music and give more detail information
His background music is acceptable and fine. You re just the type that needs spoon feeding
Are you nuts?
?