Video není dostupné.
Omlouváme se.
How to Fix Windows 10/11 Boot Error Code 0xc00000e | 0xc00000f with command prompt
Vložit
- čas přidán 23. 02. 2022
- This video demonstrates one of the ways to fix Windows 10/11 Boot Configuration Data File Missing Error Code: 0xc00000e. The error occurred after cloning HDD to SSD for a Dell Computer.
Kindly use the link below for your purchase, it helps me with a little commission. Thank you!
amzn.to/3Mwp51p
Steps to follow: ➖ represent commands and must press enter after
Get windows installation disc or USB stick with installation media
Restart PC and boot from USB or Disc (Press F12)
➖ Press Shift key+F10 to enter CMD Prompt
➖Diskpart
➖ List disk
Select your primary disk with windows, disk 0 in the video.
➖ Select disk 0
List the partitions on the disks
➖ List vol
Important!!! Make sure you select the "System Reserve Volume" partition. In the video it is Vol 1
➖ Select Vol 1
Assign a drive letter to the selected partition
➖ Assign letter =V:
Also Important to note the drive letter you have windows installed. Usually drive C, but in the video it is D
➖ exit
Set all bootsector volume to NTFS
➖ bootsect /nt60 all /force
Re-create the bootloader configuration in Volume V (system reserve partition volume)
➖ bcdboot c:\windows /s v: /f All
Note: c:\ drive letter you have windows installed. It should D in the video but it is all good (success or fail).
➖ bootrec /fixmbr
➖ bootrec /fixboot
Access denied, no problem still continue
➖bootrec /RebuildBCD
➖Yes
➖exit
Thank you! this worked! cloned ssd to a new one - deleted the old one via diskpart clean and came up with the boot error. Now back into windows finally! Thanks again!!
Thank you for the positive feedback 🙏🏾
Same I'm trying to fix it now so sad
Bro please reply
After this data will be there or not?
Please
So this doesn't work for me sadly, but i FINALLY had mine working after following the instruction from an answer on reddit titled "bootrec /rebuildbcd "the requested system device cannot be identified" " it didn't work at first but then i changed the boot option in bios to the 2nd of windows boot whatever (there are 2 option of the same name, but apparently the 2nd one was a windows recovery one), save the changes and then it works! if you're having the exact same error this might help you :)
Thanks for sharing your experience.
You are freaking genius dude!! Thank you! I kept blue screening after BIOS flash and I couldn’t figure out why! Thank you again!
This worked for me in a Asus. I cloned a ssd to a nvme with Niubi partition editor (free) , and did not boot. Now it works. Thank you !!
I appreciate your positive feedback. It's great to share your experience.
This fixed my computer. The hardest part for me was using another computer to download the windows installation media onto a usb stick. My other computer didn't want me to download the program. Fixing that was a challenge for me and got me pretty frustrated. After that I followed the steps exactly. I got a couple different results toward the end of the steps. Once I rebooted the computer though it went back to how it was before the crash. Thank you very much for saving my computer. It's been 2 yrs since I cloned my hard drive so I was shocked to have this happen.
Thank for your feedback and sharing your experience
Installed a new m.2 and was having 0xc00000e boot error, but this video helped fix it. Thanks a lot, you're a life saver
Awesome! I am glad you found the video helpful
I am a software engineer and for those who didn’t find the solution or this video did not work for them.I want to tell you that whatever caused you this problem ,this problem can get fixed 100%.
Don’t take your laptop to any one and stop wasting your money.
It is just from a DLC boot tool to now how it works contact me and i will tell you about all the steps.👍
Awesome, great to have another resource here.
@@SKYfall_Trader Hey ,first of all you have to burn a DLC boot on a “usb“ from another device see a video about burning a system on a “usb”.Then in your damaged device enter the usb then turn on your laptop or pc and enter to the boot menu by clicking f9 if your device is “HP” else click f11 after that choose your “usb” from the list .after the DLC boot loading ,you will see the DLC boot options click on mini windows after that select your current window’s version then the DLC menu will appear select “Systems” then select “NTBOOT AutoFix” after that you will see a list of partitions .Select partition C by clicking the C button on your keyboard then click number 1 on your keyboard and congrats your device has been recovered. any questions i am ready to answer 👍.
@@SKYfall_Trader Hey ,first of all you have to burn a DLC boot on a “usb“ from another device see a video about burning a system on a “usb”.Then in your damaged device enter the usb then turn on your laptop or pc and enter to the boot menu by clicking f9 if your device is “HP” else click f11 after that choose your “usb” from the list .after the DLC boot loading ,you will see the DLC boot options click on mini windows after that select your current window’s version then the DLC menu will appear select “Systems” then select “NTBOOT AutoFix” after that you will see a list of partitions .Select partition C by clicking the C button on your keyboard then click number 1 on your keyboard and congrats your device has been recovered. any questions i am ready to answer 👍.
@kali-gen from the last step, after press "y". It said 'the system cannot find the path specified.' I think i have choose the right partition for the system.
Can you help me?
You’re a life saver dude! I had tried all the other methods to no avail but the (bootsect) was the only thing I did different this time and now it’s working so I think that was the 🔑 🙌
I am glad to know the video was helpful. Cheers
People always saying this, but I will say it again. This is really helping when i got the error after cloning my windows, Thanks so much!!!
I am happy to hear this was helpful. Cheers!
Excellent bro, in my case after windows installation usb loaded, the 'repair' option didn't show up. I had no idea how to access the CMD, but the shift+f10 saved me, so I continue following the rest of the steps and its works like a charm, thank you so much bro, you're a LEGEND!
I am glad the tutorial was helpful.
When i put Y to accept last command says not found is the last step
Did you choose the correct system reserve partition?
Dude! I tried every other supposed fix out there and this is the ONLY one that I've seen with a different technique and it worked!!! So grateful, thank you!
You are welcome!
Genuinely helpful. Couldn't have done it without you.
It works on windows 11 as well.
You are welcome, good to know it worked on Win11
When I entered bootrec /RebuildBCD. It said total identified windows installations: 0. What did I do wrong?
You are just amazing i have checked tons of tutorials but nothing worked and finally your video saved my life bro
I appreciate your positive feedback ✨️ Thank you
By far the most useful video I have seen re. 0XC000000e thankyou so much. I have been researching this all day, tried everything, didn't work, (PC would not boot at all and my only option was USB for windows re-install) the technique explained in this video covered everything and actually worked! thankyou so much
You are welcome! Thank for the positive feedback 🙏🏾
Thank you. I watched many videos but only this one worked for me! :) In my case the system reserved partition was one with 99MB size and fat32 file system.
Thank you for the positive feedback. Cheers!
If I don't want to install it in the main drive 0 because its the hdd and not the ssd should I follow this but use the disk od the ssd m.2 not disk 0 hdd?
This must be done in your primary disk with windows
Best video ever, after a lot of tries of booting windows pc's this was the only one that actually worked for me!
Thank you for the positive feedback. I am delighted that you found this video helpful. Cheers
Please help , i dont have a system reserve volume , since i have selected the C disk
Send me an email of your screenshot to eazidiy@gmail.com
This tutorial really helped thanks for saving my pc
I am glad you found the video helpful. Your comment is appreciated.
Worked everytime! 2nd time doing this. Idk, when I DDU AMD driver then delete the other OS option. It comes back with this error. Planning to freshly install windows, just need to backup some of my files.
Thank you for the update.
I really want to thank you for this video, your programming skills are incredible, you saved my ssd. I tried to solve this error for like four days but nothing else worked. I'm really glad I didn't lose any programs or data or anything else. Didn't even need to clean install Windows. And I don't even know what you did to solve the problem but the only thing important is that it worked! Haha! Nice job, thanks a lot!
You are welcome
After having to fight the command prompt and my broken keyboard for a vouple hours i finally managed to fix it thanks to your guild + minor adjustments
Thanks a lot :))
You are welcome. Sorry for all the troubles you went through 😁
Thanks. Tried this, got lots of other errors along the way but the cloned SSD from the old HDD finally booted normally after restarting.
Awesome, I am glad the video was helpful
Thank you man, I was starting to get worried. Glad I found this video
You are welcome!
Dude you are a life saver. I cant believe that worked. Saved me tons of time. Thanks!!!
You are welcome. Thanks for the positive feedback. Cheers!
I am stuck in the recovery setting ( the Blue screen that says 0x000000e ) because my computer for some reason doesn't respond to my keyboard ( i tried two keyboards and no matter what key i press, nothing happens) . so i cannot press any of the options to continue. please help
Sorry to hear that, you will need to have the hardware issue fixed (keyboard). Turn off and on to see if any luck
@@eazidiy thanks. that did not help but i already fixed the issue, and i dont even know how.
@@qrcus I am glad you got the issue resolved. Cheers
How u fixed it omg
@@skoraeditz honestly, i dont even know. i was constantly tirelessly trying and i just suddenly somehow got it to work. i had to reinstall the whole system though..
Man you are awesome ! Cloned HD to SSD and BAAMM! error code oxc000000e. You ve save me, thanks a lot !!!
You are welcome
Life saver, after several videos following similar steps this one got me through and helped me to recover my files.
I am glad to hear you found this video helpful. It is my pleasure 🙏🏾
Not all heroes wear capes. Huge thank you, this video saved me!
Massive thanks for your comment, I am glad the video was helpful. Cheers!
Perfect explanation, functional tips and all very well recorded. The world needs more people like this person: caring, honest and cooperative.
Thank you, friend. Your video has been very helpful to me.
Thank you for the beautiful, positive and encouraging comment. ❤
Rrrtttttttt5rttrtttr4gng
Rrrtttttttt5rttrtttr4gngng
Bro i installed a m.2 nvme ssd and this error showed up ,can i open advanced recovery options from my hdd and select ssd from command prompt , if i did this then will it also affect my HDD or only ssd
In what order do you have your computer to boot from? Is the SSD where your windows is loaded or HDD? Restart your PC and press F12 to go into boot options and check your boot order
@@eazidiy thanks for your reply, i figured it out now everything is working fine
Great to know that you had it figured out
This video was a real lifesaver. Easy to follow and worked like so well thanks!
Thank you for the positive feedback 😊
This really helped. Thank you so much
Thank you for your feedback 😊
Worked for me no problems!! Thanks!
Thank you for your feedback, much appreciated!
İn the last method its show me : Element not found 😢 any help !?
Did you choose the correct system reserve partition to format?
Only solution I could find. Thanks so much!
You are welcome
Great video! Fixed my problem
Thank for the positive feedback 🙏🏾
Thanks bro it really helped ❤️👍
Happy to hear that it worked for you
Genius...life saver...no words do you justice. THANK YOU. I tried this several times until it worked. I must ask a few questions though.
I too had recently switched to an SSD and all was working fine. All I did was boot into safe mode and exit safe mode and that is what caused my error. What could have happened? Do you think this will happen again or did this likely fix it more permanently?
So far it as been a permanent fix for all computer I have used it on after cloning HDD to SSD. Thank you for your positive feedback!
@@eazidiy I hope so LOL...btw, what happened to the V drive designation? I don't see it now.
i cannot believe it. this actually worked... thank you!
You are welcome
Hello, for the last command with rebuildbcd, I got the error "the system cannot find the path specified".
Also my fixboot completed successfully but in the video your failed.
I tried Clonezilla to copy into an SSD but it failed within 1 minute.
The original drive is now giving this BSOD.
Any advice?
I would suggest check your boot options, make sure you are booting windows from the local disk and not USB disk.
@@eazidiy I figured it out but I had slightly different steps
Execute the command: diskpart
List the partitions on the disks: list volume
Important !!! >> Find a partition labeled ESP or EFI with a size of 100 MB. Remember it (the size and name of the partition may differ depending on the version of Windows, but the main thing is that its file system must always be FAT32).
Select this partition: eg select volume 2
Assign a drive letter to the partition: assign letter=Z find
Exit the diskpart: exit
Now you need to re-create the bootloader configuration. Copy the boot files from the Windows directory: bcdboot c:\Windows /s Z: /f ALL (replace c:\ with the drive letter on which you have the Windows installed). If you did everything correctly, the message will appear: Boot files successfully created;
Reboot your device and check if the boot problem with winload.efi file is fixed.
Thank you for your help!
@@ryansi33 Heey, 👏 👏 👏 thanks for breaking the steps further. Awesome!
@@ryansi33 man you saved my life!!!!!!!
omg been trying for two whole days trying to fix this and finally found this thank you so much man ❤
Is there a format in it?
Can you reframe the question. Sorry I did not get it.
It is success to fix this problem and follow the video step by step. thank a lot!
You are welcome, I appreciate your positive comment
3:27
Add installation to boot list? Yes(Y)/ No(N)/All(A): Y
The system cannot find the path specified
It says above line
Plz help
Hi, If you see my video description you must ensure to select the right Reverse Partition Volume.
You use these steps:
Execute the command: diskpart
List the partitions on the disks: list volume
Important !!! >> Find a partition labeled ESP or EFI with a size of 100 MB. Remember it (the size and name of the partition may differ depending on the version of Windows, but the main thing is that its file system must always be FAT32).
Select this partition: eg select volume 2
Assign a drive letter to the partition: assign letter=Z find
Exit the diskpart: exit
Now you need to re-create the bootloader configuration. Copy the boot files from the Windows directory: bcdboot c:\Windows /s Z: /f ALL (replace c:\ with the drive letter on which you have the Windows installed). If you did everything correctly, the message will appear: Boot files successfully created;
Reboot your device and check if the boot problem with winload.efi file is fixed.
Dude you are the man!! Thx for the help!
You are welcome 🙏🏾
Thank You U such a savior really appreciate for sharing ur knowledge my laptop now working smoothly and love it ❤
You are welcome! I do appreciate your positive feedback
Life Saver Life Saver Life Saver this information is legit it works once u select the correct volume it works. thanks again Eazi
I appreciate your positive feedback ✨️ 🙏🏾
Saved me a whole reinstall. Thank you
You are welcome
Hi mine failed at last stage kindly assist
I responded to your email
It didn't give me the option of saying yes or no it just said operation completed successfully what do I do should I exit
Was your boot files successfully created or it failed?
Kindly look at the description box, I have a detailed steps. Check if you missed any
@@eazidiy thx for that but I took it down to a repair shop so it's fine now apparently it was two conflicting partitions on the os drive that messed up windows but it's all fine and dandy now
@@Bandit-rd9xp Awesome! Thanks
When i list vol, there is no reserve and im not sure where to go from there
Send me a screenshot of volume listed eazidiy@gmail.com
According to the screenshot you sent, Volume 0, letter C is your system reserved partition.
Thankyou so much bro this is really worked and only for you
You are welcome
Just to double check, I've already sent you an email with the included pic showing my cmd prompt.
When listing the volume, I noticed that Volume 2 had a SYSTEM label that's FAT32 and 260mb in size.
Is this the system reserved partition?
Yes, the volume 2 is your System reserved partition
I'm having this problem, however if I go into the bios and then reboot I can get into Windows. Is that more likely a mobo issue??
Most likely a corrupt boot configuration
After i do all steps the total identified windows installation: 0
Please check the video description box for detailed steps, it is crucial to change the letter for the right partitions.
i did what you showed in the video and now ive been stuck in " You're 35% there. Please keep your computer on." for the past 30m. is that normal??🤔
Do you still have the issue?
Thanks this was very helpful.
You are welcome
System reserve partition doesn’t show up on my list, please help
I saw your screenshot, Volume 1 is your system reserved partition
After trying 10+ tutorials and 4 hours of troubleshooting, here’s what worked for me from a deleted Reddit accounts 5 year old comment with 0 likes 😂 this guy was heaven sent
SOLUTION:
On another pc, install Macrium Reflect Free and create Macrium Rescue Flash Drive.
Boot from flash drive, and select "fix windows boot problems" and follow instructions.
And that’s literally it, super simple, only thing is you need to link a google account for a 30 day free trial but it’s very easy
Amazing tutorial!! I had to re-do it one time because I didn't renamed the right system partition. Gladly I looked on the comments and our hero had the solution:
"Important !!! >> Find a partition labeled ESP or EFI with a size of 100 MB. Remember it (the size and name of the partition may differ depending on the version of Windows, but the main thing is that its file system must always be FAT32)."
Thanks again! =P
I appreciate your positive feedback.
Can u help please, in my case when i want to do the last step, it say “the system cannot find the path specified” please help
Did you choose the correct system reserve partition?
In my case, the vol doesn't show system reserve partition. So I selected partitoon C. In the last step, I ended up 'the system cannot find path specified ' . Help, please.
Thanks a lot for the video.
Can you send me a screen of your computer when you did list volume? Send it to my email eazidiy@gmail.com
Thanks Brother I support you
Thank you!
Im on the last command, and cmd prompt cant find any windows installation
Did you format the correct system reserve partition?
Thank you. I’ve tried this and it didn’t work. My disk is GPT , I see that the video is for MBR , could you please advise a GPT. Solution?
Did you clown your disk? If yes, you may want to reclown but before you do, format the new disk to GPT and not MBR
Hey it says I have a windows installation but it’s not successful. What can I do to fix it
Please see the video description box for detailed guide. Ensure the right Reserve System Partition label is chosen.
@@eazidiy what if that option is not appearing
When list vol of your primary disk, system reserve partition could be in NTFS or FAT32 usually more then 100 MB
I was having this same problem too. I’ve done everything you told this guy but it’s not working
@@NBMbrethen Check the video description box and follow the steps along with your own computer
Hey what if it says that it identified 2 windows installations? How do I select the one that I want to have it on from the other and possibly delete the other?
Do you have 2 windows installed? If yes, follow the prompt to select the one you want to install
i used minitool partition to change my ssd from a gpt to mbr will this video help fix this as i was promptedt by minitool to restart
I cannot verify that but you can try it
HEY, DISKPART DOSEN'T WORK ON AN gpt DRIVE!
Kindly look at the description box, I have a detailed steps. Check if you missed any
THANKS IT WORKS, Saving my data
It is my pleasure to help 🙂
Thank you so much this helped a lot
You are welcome!
Very nice bro 👌🙏 , actually I have facing same from last 2 days after cloning, I will try this, but in I my case partition type is gpt, it will work ? or can I rebuild the bcd using any other software please suggest me. 🙏
Did you clone from GPT disk to NTFS? Try it, make sure you format all bootsectors
@@eazidiy Thank you So much 🙏
it still gives me the same blue screen when i put the recovery media on it:(((((
You may need to take your PC for repair
hello i selected the wrong volume, after that i selected the right one and it worked. however now when i boot i see two volumes to choose XD. one that works and one that doesn't. how do i roll back the changes i did by mistake?
You can delete the wrong volume. Follow thesame steps, when get to select volume then you delete it.
@@eazidiy thank u, i just had to open msconfig and delete the wrong boot volume
Thank you bro ❤️
You are welcome 😊
Thank you, you don’t understand how much this means
You are welcome
Did not work for me after "add installation to boot list?" I got "The requested system device cannot be found."
Make sure you choose the right partition for system reserved
What i have to do when i type there "rebuildcbd" after that "Y" but then it write "the system cannot found the way"
Hard restart on your computer
Any idea on what I should do when my keyboard just doesn’t work on the blue screen error screen I’ve tried two keyboard multi times but neither work
I have tried restarting your PC to get the keyboard and mouse to work?
@EaziDIY is this method work with losing any data I'm mean I don't want to loose my personal data stored in my laptop .........pls help me
.....to confirm that
No, you won't lose your data
I got this problem when I installed Windows and it did not allow me to choose the disk, the message is related to the type of storage MBR. And then this message appeared, please what can I do?
What is your disk type? GPT or MBR? You should now your disk type
It was mbr. I didn't know so now i fixed the proplem, Now I watch the video and follow the steps but Volum System Rese does not exist, which exists
Can you send me a screen shot showing your disk partitions eazidiy@gmail.com
I know you probably won’t see this but everytime I restart my laptop and press f12 it doesn’t do anything could you possibly help?
Do you have a Dell laptop? Some laptop uses F8 or F2 key, not all uses F12 to go into boot option
@@eazidiy sorry it took me a minute but im not sure i think its a asus laptop
@@eazidiy found out it’s the f8 but whenever I press it just a black line appears from the top to bottom what do I do now?
OMG IT S WORKS FOR REALL MAN ,
"For me this cuz windows update and got sudden blackout then error winload.exe"
Damn man thank you, you solve my problem ❤❤❤❤
28 may 2024
I appreciate your positive feedback ✨️ 🙏🏾
it cant identify a windows installation in last step. what could help?
Did you choose the right system reserve partition?
I am really impressed. TY
You are welcome!
tyyy it saved my pc love u😭😭
I appreciate your positive comment.
It says the request system device could not be found on the last step could you help me
Please format the correct system reserved partition.
I can't get the boot mode to show up. No matter how fast I hit F12, it just takes mee to the error screen
Did you confirm if your computer boot mode is F12, F8 or F2?
En mi caso funcionó, casi a la perfección, después de hacer todo lo que muestras en el vídeo marco que no había sistema, arranque nuevamente con la USB y le di reparar inicio y ya funciona, muchas gracias
De nada mi amiga
i have 5x times with this error , but after restart pc this error is gone , but is coming again with random moment .
is this my ssd broken or my windows corrupt ?
should i try this method ?
It seems you have a corrupt partition or faulty ssd due to the frequent occurrence. You may try this method to see if it rectifies the error.
what if i repair bootrec in desktop cmd, not in usb installation media,
is it safe ?
I do not know how safe that is
They no usb. How to fix this laptop/pc without usb?
This method requires USB
If ur PC accidentally turns on
Then press Shift and restart ur PC (click on restart while holding shift on ur keyboard )
Click on troubleshoot -> advance options -> Command prompt
Then follow the steps in the video
Bro please help me. After i enter diskpart it doest let me type qnything else. I am stuck here. Please anyone help
Are you able to fix it?
Unfurtunately it didn't work for me. I still have the same error message.
But my system is a bit more difficult. There is an old indos on it. The Boot Partition is Primary but all the others are in a logical partition. So it seems likely:
| Boot (hidden?) || Logical +++++++++++++++++++++++++++++++. ||
| +++++++++++. || Windows 7 | Windows 10 | DATA ++++++++++++ ||
While booting windos 10:
| NONE | Letter D | Letter C | Letter E (I think).
You may need to take your PC for repair
Dear @@eazidiy ,
I could fix it. I just ussed a little bit different method. The main thing is, that the bcd has to connect the windows partition to boot from with the UID of it. Your method is really good but maybe you did not explain deeply enouh, what I needed. ;)
But thank you!
It does not say system reserve partition
It should a volume with MB size
You’re that old video that is always there to save us
I am glad to know the video was helpful
Thank you very much!!!
You are welcome.
To begin, am I need to download the installation files.
Yes!
ok but where to get the program that goes into the usb?
Download it from Microsoft website.
Thank you so much brother
You are welcome!
Great. Work's.thank you
You are welcome!