Installing PVC trim at The Everything Garage (Part 8)
Vložit
- čas přidán 28. 08. 2024
- PVC trim goes up around the windows and doors, as well as at the corners, bring The Everything Garage one step closer to completion. Cellular PVC trim is my go to material for anything that will see moisture that could lead to potential problems. It's rot resistant and can be treated just like a wood based material. Cellular PVC trim can be nailed, screwed, patched, and painted to give a clean finished look without the constant upkeep.
Planning The Everything Garage: • My dream garage: Plann...
Our design studio: www.thehomestu...
Pinterest: www.pinterest....
Instagram: / homestud_studios
My tools (though very few have been used in this project yet!):
Finish Nailer: amzn.to/3hltQKT
Router: amzn.to/3g4ZXPw
Brad nailer (newer version): amzn.to/2SJpNif
Compressor: amzn.to/2YOpsyK
Air hose: amzn.to/2yH7DGT
Speed square: amzn.to/2A5dwxY
Hammer: amzn.to/2YT31sd
Table saw: amzn.to/2SRn2vn
Track saw: amzn.to/35JOQH1
Miter saw: amzn.to/3fC92zs
Impact drill: amzn.to/2SKVdEQ
Level: amzn.to/2SMMamO
Planer: amzn.to/2ZRQHJg
Love your precision and attention to detail. Must be that Microbiology PhD.
Haha thanks- I'm sure it didn't hurt
Did you use Acetone on the cut edges to keep it from staining and turning brown. Someone on Home Depot site quoted: Fine sand paper then acetone with a clean rag rubbed on the cut surface will smooth out the cut edge sealing it for the most part keeping out the tiny dirt particles preventing mold from growing and staining.
locked up chuck? spin in reverse while tapping on chuck many times fairly hard with linesman pliers or hammer. should break free in no time.
Oh wow, I was worried you were gonna tell me i have to use some sort of glue. Thank you!
Gluing the corners will probably be beneficial in the long term for stability and preventing the joint from opening. However, I haven’t had any problems yet and mine aren’t glued.
So what kind of nails are you using and how did you fill them? Given the rot proof nature of pvc Im trying to find fasteners that wont rust.
Great job your a pro
What type of nail gun are you useing for this job...also what size nails.. Great Work your doing...
I am using Milwaukee's 15G finish nailer with exterior 2 1/2" nails (pretty sure they were 2 1/2")
hello good morning. I have a project at home. I want to put vinyl siding and I'm thinking about installing pvc corner and then putting g chanel. I would like to know if that can be done and if so, what width measurements do I use to put the corners that are seen in the video. thank you
Why no PVC glue on your connections?
I have had my drill bit stuck. I put it in a vice and put it in reverse
I thought about that. But the problem wasn't stopping the chuck, I could do it with my hands. The problem seemed to be when the chuck was stopped, the internal geared didn't engage to back off the 3 teeth. Maybe a quick shot in reverse in a vice would have done it. Either way, fixed now!
I have a question…my molding wouldn’t stay in place where the vinyl meets the brick siding how do I fix this? Is there a glue that they sell my dad tried to add screws but that didn’t work.
Are you screwing into a solid backing, not just plywood? All of my moulding is attached into 2x6" framing behind the plywood. To answer your question though- PL premium glues anything together haha
Apparently not all glues and caulks are recommended for pvc. If it doesn’t state it is don’t use it.
Could you have used and 16bgauge nailer with PL. Sufficient?
Probably? PL extreme will stick pretty much anything together haha
I had my drill lock up. I bet on it and channel locked it . Lol a waste of time . Trash it. It happened with the same type of bit ironically. ! Maybe that has something to do with it.
I have a trim piece horizontally around the house that is at about the floor level of the second floor. What is this trim called?thank you
Is it just a trim piece dividing the rest of your siding/exterior finish?
Which brand of trim are you using in this video
I believe it was called Veranda
What size/gauge nails did you use on the trim?
They are 2" 15g nails.
@@hsdesignstudio trim screws better? do u putty nail holes? is that a batt powered nail gun? if so, what's the make?
@@johnboggs8765 In the past I have used trim screws, but I didn't own the 15g nailer at that time. I thought for this project (since it is my own garage), I would see how it worked. I do plan on filling the nail holes with the appropriate filler in the spring, as well as painting all of the trim. The nailer is Milwaukee's 15g finish battery nailer.
What type of filler do you use for PVC?
Just one from Home Depot meant for PVC
@@hsdesignstudio thank you
What kind of cordless nailer do you use for pvc? please let me know thanks
I'm using the Milwaukee 15G finish nailer
What’s the difference between using 15G finish nails & PVC trim screws?
How does this compare to hardie trim?
I've never actually worked with hardie board trim, so I can't give you a good comparison. If I was doing Hardie siding, I'd probably lean the Hardie trim as well for continuity. Same goes with vinyl and PVC trim.
Hardie Trim are a pain in the butt to cut compare to pvc. Pvc will cut like wood while Hardie is more like cutting masonery. Apparently both will kill you eventually so I made my choice on the one that is easier to cut!
Loved the video, thank you! Just one tiny comment, your voice goes high often when excited or asking a question. Suggest keeping your voice low, much more pleasing to the ear. (Just a tip from an old video producer)
Thanks for the tip!
The great thing about CZcams videos is that you can be yourself, you are not an actor and portraying someone else. Sylvia, what if this CZcamsr had an issue growing up with people making fun of him? Stop trolling….
Hollyweird Producer? Of course, you wouldn't want someone to just be themselves! Which is why America is tuning out Hollywood and tuning into real people! God Bless
Minus the 1974 porn bush music
Chillhop*