Single Cup Turner Build Tutorial | DIY | Epoxy Resin Cup Turner
Vložit
- čas přidán 6. 02. 2021
- Thank you for watching my tutorial on how my husband builds my cup turners for my Epoxy Tumblers and Epoxy Pens! This video is designed to answer numerous questions about my turner setup. I hope you found it helpful!
We have officially launched our KCC Glitter website, check it out here! kccglitter.com/
About me: I have been making epoxy tumblers for approximately five years and have decided to share my methods with aspiring cup makers. Everyone's methods are different and I just want to share what I have found to work best for me!
Buy me a Coffee 💕 No pressure at all but if you would like to help support the channel and the tutorials I create, you can use this link to leave a tip. 💕 www.buymeacoffee.com/KCCyoutube
Please feel free to comment if you have any questions at all! Below is a list of links to some of my favorite products that I use the most to make my tumblers.
If you enjoyed my video, please give it a thumbs up and hit the subscribe button to see more videos like it!
Check out our Facebook group! / epoxytumblersandpens
Materials Used:
- 1"x6" premium pine board cut to 15" long
- (2) separate pine board pieces cut to 5 1/2" x 6"
- Large hole is with a 1 1/8" holesaw
- Small hole was drilled with a 1/2" drill bit
- Titebond II woodglue - amzn.to/3tHQyV8
- 16 ga 2" straight nails
- PVC glue - amzn.to/3p7dERm
- 3/4" PVC slip on threaded male adapter
- 3/4" PVC plug
- 3/4" PVC slip on female adapter
- 9/64" drill bit to drill hole into PVC cap
- 5 1/2" for PVC piece attached to motor
- 6 1/2" for PVC arm attached to foam football
- 1 1/8" hole saw for foam footballs
Recommended Glitter:
KCC Glitter: kccglitter.com/
Tumbler Supplier:
MakerFlo - bit.ly/3RQMflM
Products I use frequently and highly recommended:
Silicone Mats - amzn.to/32YW5Lf
Cup turner motors - amzn.to/2IWXBGI
Bee Jay's Glitter: www.beejaysglitter.com
GlitterBae Glitter - www.glitterbae.com/?ref=krist...
Tack-It - amzn.to/3ao2nGX
Apple Barrel Paints - amzn.to/2Mn6ACP
Rust-Oleum Flat White Spray Paint - amzn.to/3nILLz1
Cup Turner - amzn.to/3l1xBaw
Butane Torch - amzn.to/3pM06wr
Paint Brushes - amzn.to/36xlZaO
220 Grit Sandpaper - amzn.to/3rYKC9j
Rust-Oleum Gloss Clear Spray Paint - amzn.to/2HfFKKm
Gloves - amzn.to/36QSrUP
Plastic mixing cups with measurements - amzn.to/3lLARrG
Medicine cups - amzn.to/3kQFQWC
Zippo Butane Fuel - amzn.to/3lT39Ra
Chip Paint Brushes - amzn.to/373Z4V7
Alcohol Ink - amzn.to/3oH4paG
Cup Turner Foam Inserts - amzn.to/2UKBQfE
Blingasm Waterslide Paper - amzn.to/3fcRiL8
Faux Rizzle Epoxy - amzn.to/2IT02dI
Counter Culture Epoxy - amzn.to/3pRzFW6
Painters Tape - amzn.to/3lRGuVa
Popsicle Sticks - amzn.to/3nG33fU
Paper Mate Pens - amzn.to/3o0Lh7n
Wooden Dowel Rods - amzn.to/37WBrOD
Faux Rizzle Epoxy - amzn.to/3nZFM9h
Counter Culture Epoxy - amzn.to/3pRzFW6
Finger Cots - amzn.to/3qprjo0
Epoxy Mixing Cups - amzn.to/3s200C0
Oracle 651 Vinyl - amzn.to/399SUCM
Turner Foam Inserts - amzn.to/2XkuEZ7
Craft Knife - amzn.to/3pXOlCk
Decal Applicator - amzn.to/2MFMOm2
Connect with me on Social Media!
/ epoxytumblersandpens
kristicustomcreations
kristicustomcreations
Video music from Epidemic Sound, you can try a free 30 day trial by using my link! www.epidemicsound.com/referra...
*Disclosure: I only recommend products I would use myself and all opinions expressed here are my own. This description box may contain discount codes and affiliate links that at no additional cost to you, I may earn a small financial benefit. As an Amazon Associate I earn from qualifying purchases. This helps support my channel so I can continue to provide you with inspired and focused content. Thank you. - Jak na to + styl
70 yr old grandma going to make my own turner. Thank you for a great video!
Thanks for sharing! Your husband did a great job and your narration was great, too.
Thank you so much 🥰🥰🥰
Thank you for sharing!
My pleasure!
Thanks, just naming the screw size is a big help to me. Saves me a lot of time.
Great video you both did! Excellent instructions.
Thank you so much 🥰
Thanks for the easy to follow tutorial! Super appreciated
You're very welcome and thanks for watching! 🥰
Thanks for this video! You guys explained everything perfectly and in great detail. Another thing to add to the “To Do List” for the hubby 😁
Thank you!!!! 🥰 My hubby's to do list is quite long too! 😉
THANK YOU THANK YOU THANK YOU!!! This was perfect!!!
You're welcome! 🥰 Thanks for watching!
Omgosh this is the best tutorial...thank you to you and your hubby for this ❤
Aww! Thanks so much!
@@KristisCustomCreations you're most welcome 😊
I sure wish I had this video when I was making mine!! This was awesome!!
Thank you! 🥰🥰🥰
Very helpful ❤
Thank you 🥰
This was incredibly thorough and easy to understand. Thank you both!
Thank you and thanks for watching! 🥰
I dont mean to be offtopic but does any of you know a way to log back into an instagram account?
I was dumb lost my account password. I appreciate any assistance you can offer me
@Dominik Kai instablaster :)
@Izaiah Edwin i really appreciate your reply. I found the site thru google and I'm in the hacking process now.
Looks like it's gonna take a while so I will reply here later when my account password hopefully is recovered.
@Izaiah Edwin it worked and I actually got access to my account again. I'm so happy!
Thank you so much you saved my ass :D
Thank you. This was great.
You're very welcome 🥰
Yesss!!! Ty so much
Great video thank you so much ✨ nice and clean process 😉
Thanks and thanks for watching! 🥰
LOL, you think your husband can stop by and make this for me. Just kidding. I don't do tumblers but your DIY video on ice tumbler lids sure helped me. Watched others and your idea using the UV flash light and foil underneath is fantastic. Thanks for sharing. I am 70 yr old and after I lost my wife and retired enjoy making them while at the same time making a little pocket change.
I'm so glad that my tutorial helped you! I'm so sorry to hear about your wife. It's definitely nice to be able to make a little extra pocket change and crafting definitely helps keep your mind busy when needed. 🥰
Excelente video!!!! Muy bien explicado!!!!! Muchas Gracias!!!!!!!!!!!!
Thank you! 🥰
Incrivel! Parabéns!
I'm from Brazil!
Thank you for watching 🥰
Next we need a tour of your tumbler workshop!
Lol! My work area currently looks like a bomb went off! I will definitely try to share it with everyone soon though. 🥰
Thank you, So easy I think I can make one for myself. When I get brave that is. Ha
😂😂
Hi I just watch the video on how to make your tumbler. I bought a 1/2 inch wide pvc pipe so How big would I make the hole in the wood for 1/2 inch pvc pipe and how many males and female parts do I I need? Thank you for this video!❤️🥰
Hi Kristy , hello from the UK , Very informative , if I decide to do colouring beakers I will definitely drop by and watch again ,, actually I'm a woodturner checking out the wiring , I'm making a motorized turntable , I have the same make and model as yours (AC 100 - 127v ) I know nothing about electric , wired it up as shown , left it running while l found the "grub screws" and the allen wrench , it was over heating and got rather hot ,,. Don't know if it's the voltage ( UK runs on 240volts ) hoping for advice ,,. Stay safe ,,. Regards Alf
It may be the voltage. I literally know nothing about electricity and wiring but here in the US we mainly run on 110. The motors do tend to get warm but I've never had one overheat. I hope you have a wonderful day!
@@KristisCustomCreations Thank you for replying ,other channels using that motor that I had ask for advice just deleted me ( how rude) lol,,. I'm told that there are gizmos that can " step down " voltage ,, so that's my next move,, thanks again ,,. Stay safe , Regards Alf
Thank you Kristi and thank your husband for the demonstration. I was thinking WHO I could hire to make one for me? Will you be selling any of these? Can I share my address and "hubby" can make it for me? (just kidding!). Thank y'all for showing us that!
What is the name of the brass fitting you attached to the motor with the two Allen screws and where can I buy it?
How do you release your turner rod?
Please thank your hubby for this video. He did fantastic. He's a pro CZcamsr. (sounds sarcastic, but I only mean how he's showing products.
Lol! He was being super silly a couple times and I had to edit those parts out. Thanks for watching! He will appreciate knowing you enjoyed the video. 😉🥰❤️
I love the part where he was displaying the football like vanna white🤣🤣
@@karihaldeman346 girl, I had to edit out so much crazy stuff he was doing while I was recording 🤦🏼♀️🤣
I have zero skills for doing things like this. You are blessed to have a handy hubby. 😊.
But I have a serious question. How much would your husband charge for 1 turner w/o the football?
He and I actually aren't together anymore. There are some really nice handmade turners available on Etsy though.
@@KristisCustomCreations oh hun. I'm so sorry 😞. I didn't know.
@@andreatthatsme oh it's ok... Things are really great for me and my son now. 🥰
@@KristisCustomCreations thank you. I found a turner on etsy. I'm waiting for it now. 🤗
@@andreatthatsme yay!! Which one did you end up getting?
Where is the link to purchase the motor on Amazon?
Could a turner like this be made with a section of a foam pool noodle instead of the football?
Yes ma'am! You could absolutely do a pool noodle instead of a football.
Do you have a part# for the motor assembly? TIA
Can it be used with foam instead of football?
Yes, you can use foam also... basically just anything that will hold the tumbler onto the PVC will work
My husband followed your video and made one of these. I have a question about the motors….mine are getting really hot to the touch.
Have you found this to be the case as well? I’m afraid to let it spin overnight.
Yes, the motors do get quite warm so make sure that you don't put your Turner all the way up against the wall. I don't allow my motors to touch the wall. I run my turners overnight all the time and have never had any problems.
@@KristisCustomCreations Thank you for the information. I was getting worried since they were so hot. I was afraid to let them run overnight.
@@danied180 you're very welcome. Only do what you feel comfortable with doing. My personal experience is that I have no problem letting mine run overnight. I actually have seven spinning tonight that will run all night.
Did you say about how much this cost to build? I didn’t catch it if so
I didn't put a price in there. It's hard to say how much it was because I had him build 7 separate turners for me all at the same time. Before the price of lumber went ridiculously high, you could probably build it for no more than $15-$20
Where do you purchase the motors at?
About them on amazon, there's a link for them down in the description box 😉
Thank you so much
I must’ve overlooked them
@@causehelives15 when I get back to my computer, I need to move them a little higher up the list so they are easier to find. I think they are close to the bottom of the list.
Does he just sell the wood parts? I could do the rest! If so I need like 10!
Dose he make this to purchase?😁
Unfortunately not. I had him make them for a tumbler workshop that I was hosting.
Ok...where can I buy these turners ?! I need about 6 of them 😁🤣!!!
Lol!!! They are awesome and sturdy turners! Too bad you don't live closer! 😜
@@KristisCustomCreations I knowwwwww...😭😭😭😭!!!
@@customdesignsbydae2420 I have a couple extra that he made but I think shipping would be SO much.
Can you give me the directions in writing and what kind of wood you used Thank You In Advance Love Your Videos
@@CrystalWilliams-rt3zm yes ma'am, I will put the instructions in writing tomorrow and add them to the description box 😉
If hope your husband feels better he sure is doing a lot of coughing
Thanks, he had actually just gotten over covid and was still struggling with a cough.