How to generate a base map!
Vložit
- čas přidán 20. 07. 2024
- Cameron, FuelTech USA's Tech Supervisor, shows you how to generate a base map, configure inputs and outputs and much more!
0:00 to 00:20 👉 How to open the base map generator and select the features you would like to use
00:23 to 00:50 👉 Engine Setup
00:50 to 1:14 👉 RPM Signal Configuration
1:15 to 1:30 👉 Ignition System Configuration
1:31 to 1:48 👉 Fuel System Configuration
1:49 to 1:57 👉 Throttle and Idle Control Configuration
1:58 to 2:17 👉 Base Map Generation and Engine Characterization
2:18 to 2:41 👉 Wiring Harness Diagram
2:42 to 2:53 👉 How to Open the Quick Access Panel
2:54 to 4:00 👉 Input Configuration
4:01 to 5:05 👉 Outputs Configuration and Testing
5:05 👉 How to select a 3D Fuel and Ignition Table vs Line Mode
Step by step article 👉 www.fueltech.net/blogs/articl...
FuelTech Tech Articles 👉 www.fueltech.net/blogs/articl...
Like the video? Don't forget to like, share with your friends, ask questions and SUBSCRIBE 🔥
- - - - - - - - - - - - - - - - - - - - - - - - -
Follow us on social media
- - - - - - - - - - - - - - - - - - - - - - - - -
→ / fueltechusa
→ / fueltechusa
→ www.fueltech.net
Learn more about the FuelTech Hub Dyno Experience 👇
www.fueltech.net/products/adv...
Learn more about the FuelTech FT Education Training 👇
www.fueltech.net/products/ft-... - Auta a dopravní prostředky
How to invert axis to have rpm column and map in Row?
So would this software and available ecu's work for motorcycle engines as well?
After setting the base map, install the sensors and control unit FT in our car, with this base map that we created, do is sure that the car will turn on? Off course, after the engine work, we do a adjustment more precision, in all engine situation. Thank you for our support.
Marcos Oliveira yes most vehicles will start and idle after using the setup wizard. However some of the more wild combinations can use some adjustments to make them idle perfectly.
-Cameron
Hi, generating the base map went easy but I can't figure out how to regenerate the base map when changing engine settings. For instance, I doubled the total injector flow but can't get any injection time update on the fuel map. Am I missing something ?
Crank index position? What’s that ? How do you know it’s 50? Not familiar with that term.
Is it possible to run a single cylinder with twin spark (2 spark plug at the same Time
Hey Mario, Ok so for your coils you will use 1 grey output configured as cylinder 1 ignition and split it to both channels on your spark pro 2.
is it possible to tune the fuel in Volumetric efficiency? or is it only injection time based?
11 22 Our system is an injection time based system, We do however have a calculated VE option if those are numbers you are more use-to seeing. You can swap between ms,DC,lb/hr and VE using the F6 key on your keyboard.
-Cameron
@@FuelTechUSA Hi, how to make sense of VE without specifying engine displacement ? I switched my OK-working map to VE and it barely goes above 50% for a turbo engine.
Y si fuera una gsxr 600 2008???
👍
trying to start my 2jz ge
>intro
Goodbye eardrums...
this is not good enough for a beginner. you should explain one by one the option on the menu
read the manual, learn, dont expect everyone else to do the hard work for you...
what a loud unnecessary loud intro sound