Awesome! Always wondered why my steering freaked out when when I flipped my Gen8 over to work on something and it was on. Never knew it had a gyro in it. Have to turn that setting off for this model. I will DEFINITELY be keeping it on for my Shumacher Procat K1 though... that thing is so squirrely unless you eeeeeaaassseee on the throttle.
hello, back again😂 i was reading your comment again, the last sentences there, what you should do is at the svc setting keep that on, scroll down look for throttle gain, set that on and go to something like 70% and try taking off full send, what it does it that it cuts back throttle when the vehicle gets sidesway and regain throttle once it straithens(i fuked that word up😂) out. lower that number and try again until u can control the squirry fishtailing. ALSO, Priority: set it to on and keep it on a low %#, the gyro will keep that car,,,,,,,, mmmm, think of it as if its making the car run understeered, so the faster you go the less steering the reciever will do even if u steer the controller all the way, the gyro will prevent a spinouts. so the slower u go the closer the steering circle will be. the faster u go the larger the steering circle will be. this is usefull when going from 10mph to full speed pass, circuit racing.
I need help with mines I’m running a castle momba monster x 8s and TP motor and on the controller it says it don’t accept it. Meaning I can’t use with with this setup I’m not sure what’s going on I have a power HD brushless high voltage servo
so your controller, the radio transmitter says that? i have never seen anything like that before happen. my boys they run that setup mm8s with tp motor for their speed runs they insane.
For some odd reason my car keeps going to left a little I tried everything to get it to go streight do you have Instagram I can maybe share you what’s happening cause I definitely need some help
Awesome! Always wondered why my steering freaked out when when I flipped my Gen8 over to work on something and it was on. Never knew it had a gyro in it. Have to turn that setting off for this model. I will DEFINITELY be keeping it on for my Shumacher Procat K1 though... that thing is so squirrely unless you eeeeeaaassseee on the throttle.
wow i see, yeah i want to say that this transmitter is fully complete and alot of ppl domt even know aboit the svc (gyro), it even has crab steering😂
hello, back again😂 i was reading your comment again, the last sentences there, what you should do is at the svc setting keep that on, scroll down look for throttle gain, set that on and go to something like 70% and try taking off full send, what it does it that it cuts back throttle when the vehicle gets sidesway and regain throttle once it straithens(i fuked that word up😂) out. lower that number and try again until u can control the squirry fishtailing.
ALSO, Priority: set it to on and keep it on a low %#, the gyro will keep that car,,,,,,,, mmmm, think of it as if its making the car run understeered, so the faster you go the less steering the reciever will do even if u steer the controller all the way, the gyro will prevent a spinouts. so the slower u go the closer the steering circle will be. the faster u go the larger the steering circle will be. this is usefull when going from 10mph to full speed pass, circuit racing.
@@nunu4692 - Awesome! Thanks for the tips!🎯
Mines is just finished and it wont move is dat has anything to do with any remote settings new to the rc world
Question, regarding Ch5 and Ch6? Is it possible to have a esc on each channel and operate them proportionally in forward and reverse (with neutral)?
YES, Both channels goes from -100 to +100, 0 being neutral.
Basically in a nutshell, the gyro counter steers for you 🤷🏽♂️ thanks for the help.
yup, it keeps the car straight
I got the same controller but I hear some loose thing inside it when I shake it, is that normal?
no i have the same i
andddddd its not doing that
i have a new one, i dont hear anything.
Screw loose
I need help with mines I’m running a castle momba monster x 8s and TP motor and on the controller it says it don’t accept it. Meaning I can’t use with with this setup I’m not sure what’s going on I have a power HD brushless high voltage servo
so your controller, the radio transmitter says that? i have never seen anything like that before happen. my boys they run that setup mm8s with tp motor for their speed runs they insane.
@@nunu4692 I figured it out I was on the wrong settings
For some odd reason my car keeps going to left a little I tried everything to get it to go streight do you have Instagram I can maybe share you what’s happening cause I definitely need some help
send me a link to the video right here
@@nunu4692 okay I’ll make a video tomorrow