DIY Wedding Arch & simple sleek base Part 1. Build a strong Wooden Geometric Hexagon boho backdrop
Vložit
- čas přidán 30. 08. 2020
- This is Part 1 of the Wedding Arch Build Series: In this video, I show you how I built a hexagon wedding arch using basic power tools to cut the joinery (double rabbet joints and cross half lap joints), and a pocket hole jig to secure the lumber together. With the right skills and time, you could cut the joinery with hand tools.
Since it is secured with pocket hole screws (zinc coated (indoor use) 2-1/2” Kreg pocket hole screws for soft wood), it's easy to assemble and disassemble, and stores EASILY.
No brackets or metal supports are needed for the DIY. You would think this arch would be flimsy, but it is a very solid and strong. And in the video, I prove it.
I show you how to calculate the angles to make a very strong double rabbet joint. You will also learn how to make a support base that blends well with the lines and shape of the wedding arch.
Part 2 is some tips on using a router to ease the edges, how I made the stain, and how I was able to produce a smooth satin finish. - Jak na to + styl
Hi Bobby. I followed your video and made my wedding arch, and my wife loved it. We're thinking of using the arch again for another event, but the pocket hole screws stripped the wood (douglas fir, 4x6 - some parts are soft). Do you have suggestions to modify so the arch can be re-assembled multiple times?
Glad your wife loves it Alex! Sorry about the stripped holes. I would repair it by over drilling the holes for oak dowels. Glue in the dowels, and flush cut when dried. Pre drill some pilot holes for the pocket screws and that should do it.
I've used the arch for at least five events (weddings, gender reveals, etc.) so far, with no issues with stripped holes. I used kiln dried pine which is soft. I used pocket screws for soft wood, and when I used my driver, I made sure it was set to low torque, and if needed, I tightened it the rest of the way by hand.
Good luck Alex!
@@doitstepbystep3376 Thanks Bobby for responding! Just wondering. Is there some nut-fastener option to use in the pocket hole so I can reduce the need for the woodscrew cutting into the wood all the time?
@@Alex-jv7zh AH! Do a search for "brass wood insert nuts" Maybe if you find the right size, along with the correct bolt length, that will get you on the right path to a solution!
@@doitstepbystep3376 YES! Thank you thank you!
@@doitstepbystep3376 @Alex In regards to the brass wood inserts, they seem to focus on being 90 degrees (straight). Would these work in a pocket hole situation? Just wondering before purchasing. Thanks.
Thank you for the detailed tutorial. I will be making this as an arbor for my roses. I look forward to more of your videos.
You are welcome! Hope all goes well 👍
This is amazing. I am going to make a wedding arch for a friends wedding and I enjoy the interlocking of the joints. Great job!
Hi Charles! Thank you for the comments. Good luck with your project, and please feel free to contact me if you have any questions. ~bobbyV
This video is beyond amazing..I absolutely Appreciate you for taking the time out to explain everything in details. So precisely 👏 👌 Done! Thanks A Millon
You're welcome Amber and thank you for your comments! I hope to do more videos soon.
This is so awesome. Thank you so much for taking time and making these videos! God Bless!
Thank you JAG! Blessings and peace to you!
This is awesome! Thanks for taking the time to go in details, very helpful! I am completely new to woodworking but I am still going to try it for an event next weekend. I watched your other video for making the bases, that clears up lot of doubt. Thanks!
Hi Parag, I appreciate your comments! I hope your build goes smooth and easy. Feel free to contact me if you have any questions about your project. Good luck on you woodworking endeavors!
If you did it how it turned out?
I feel like you need more views! Out of all the wedding arch CZcams videos this is my favorite. Great job!
Thank you so very much Ashley! I hope to have more videos in 2022.
You tha best, pops. Thanks
Thank you!
Building a hexagon arch for my wedding coming up in October. Never did any type of wood work before so hopefully i dont get too frustrated at the project. This video does help a whole lot so thank you for posting.
Hi Zachary Boyd. Thanks for the comments! This video may help: czcams.com/video/x4J0TIL4Mcc/video.html It shows the steps to make a cut template. Make two so you can verify the fit. I hope the best for you and do not hesitate to ask questions!
@@doitstepbystep3376 Thank you for the additional information! If i have any questions ill make sure to ask :)
I'm doing this with rough sawn Hemlock for a barn wedding, thanks for posting this.
That should look amazing!
Hi, I want to make this arch for my garden. So I’d like to make it without the bottom bar. Any recommendations for how best to do this for stability!
Thanks for video. Best one I’ve watched, and I’ve seen a few!
Thank you for the comment!
Hmm. I live near the coast and it can get breezy in my garden. I would build another arch and make it a standalone 3D hexagon. I would be brace them with wood at maybe two foot spacing and see it I like the proportions. Maybe have a jasmine vine grow onto it.
Great video! Do you have a video on how to make the templates? Thanks!
Hi beautiful job ! Could make a white and light circle ⭕️ for a wedding! Please and thank you
Something to consider! thanks!
This is an awesome video! Thank you for sharing! How long are the pocket hole screws that I should use?
Thank you for your comment! I used zinc coated (indoor use) 2-1/2” Kreg pocket hole screws for soft wood.
Great job. Thanks I want to do one for my daughters wedding. If I wanted to do a heptagon (Instead of a hexagon) I’ll make my cuts at 22 degrees right?
Thanks for the comments Lyndon. A Heptagon has seven sides. Hmmm. This would require some prototyping and trial and error to get the cuts just right. To save yourself $$, I would prototype a smaller version using an 8' 1x4 and cut seven 1' pieces. If you use the same calculation method as the hexagon, then it would be 360 divided by 7 which equals 51.42. Divide that by 2 and that equals 25.71. Not a very easy angle to measure, so I would start there, and adjust the cut as needed. Once you know that the angles work, you can scale it up to the 2x6s. I hope this helps!
Awesome job! I’m about to built one to my wedding friend.. what are they mesures for each piece ?
Since I used an 8' lumber, each side I cut is just shy of 4'. Good luck with your build!
Anyone know a link for some recommended wood from B & Q (UK) ? Also sorry, what size of wood would I be looking to buy?
I have to do this weekend that you for this video , are you able to do a quick video on how you made the two bottom arch supporters
Hi Erica! I don't think I will be able to record right now. It's raining here in northeast Florida.
You might find the information you are looking for if you go to the 9 minute mark in the video. I attempt to explain the measurements I used to make the base supports. Please check there, and if the weather clears soon, I'll try to make a quick video on the base supports.
Good luck! bobbyV
Do it Step by Step Thanks for responding , I’m going to try it with the jig saw , I don’t like to use the jig saw but I’ll give it a shot !
Do it Step by Step can you do a video on making a template ? And does the 4 2x6x8 include the base support or do we need addition for that ?
Hi Erica! For the half lap joints, I used circular saw to cut the 2.75" lines, and a jigsaw to cut the small 1.5" line. A helpful tip is to drill a hole in the corners of the half lap joints so you can insert the jigsaw blade to cut the 1.5" line. Also, I used the circular saw to cut the slopes of the base supports. I hope this helps, and that you can Do It, Step By Step.
Hi Erica, You can make a template using the measuring directions in the video. I used a piece of MDF that is the same width (5.5") as the lumber and 12" long. MDF is very easy to cut, and strong enough use as a template.
If you are careful with your cuts, four 8' 2x6s will be enough for the hexagon, and base supports.
Three 8' 2x6s will be used for the hexagon sides
And one 8' 2x6 will be used for the base supports.
You should end up with one 2' section of lumber not used.
Thank you for all of these videos, they are helpful. So, if I don’t have a miter saw, should I just cut three of the 2x6x8s in half and use my template on all 12 of the resulting ends?
Hi Andrew. Thank you for your comments. Yes, instead of a miter saw, a circular, jig, or hand saw can be used! Just make sure that when you cut the 8' lumber in half, to cut it at an 30 degree angle to maximize the length of each piece, just like in the video.
@@doitstepbystep3376 I ended up just cutting each 8' piece in half at no angle. Everything worked out but I guess I didn't fully maximize the length of each piece. Still, it looks great, though!
@@somecatdad Awesome! Congrats!
Hi Bobby! Amazing video, my fiance and I are planning on making this for our wedding this May. However, I'm unfamiliar with pocket hole jig sets, so can I ask which one you're using in the video so we purchase the right thing? I've seen so many different jig sets from Kreg that my head is spinning. Thanks so much in advance!
Hi Olivia, thank you for your comments! I am using Kreg system KPHJ320, comes with two jigs and spacer, sample screws, drill bit, and driver bit. It is less than $40. Well as of now it is less than $40.
Question, should you cut the 30 degree angle for every piece first before making the rabbit joint? Wouldn't that shorten the overall length? Or should you just use the template to maximize the length of each piece of wood?
Hi, and thanks for the question. I maximized the lumber by cutting 30 degrees in the center of the 8' 2x6. Then like in the video, I measured the 30 degree at the very tip of the other end.
A template helps tremendously, just make sure you know your cutlines so the dimensions are equal and that the ends are mirror images of each other, not flipped. Good luck!
Thank you for this video! Could this be done on a bit larger scale to accommodate a taller couple? Do you have any recommendations?
Hi! I am sure that the dimensions can be scaled up to accommodate a taller hexagon. Just need to use lengths longer than 4'. The one I built is almost 7' tall and 8' wide. In this video czcams.com/video/0MyPcRHUTsA/video.html the groom is 6'3" and the minister is almost 6'4".
Thoughts on making one finished segment, and then using it as a template for the rest of the boards.
Good idea. If you do try this, do one, and then size it up to make sure the fit, and are dimensionally the same. Like any template, you just need to understand "where to cut" when you transfer the lines to the next piece of lumber.
Question, can you make this collapsible? Where it can be used multiple time in multiple locations?
Hi Kissha! Yes it is. In this video czcams.com/video/pownFIMcDho/video.html you can see it in parts at the beginning, how it was assembled, and at the end, how it can be stored in sections .
I have used this arch at two weddings, and as a backdrop for a gender reveal. Even more events scheduled of 2021.
@@doitstepbystep3376 THANK YOU✨
I used hand tools (I don’t have a miter saw) and my angles must be slightly off. I can get 5 of my boards flush, but the 6th has gaps. Any suggestions on how to tighten my angles? I’ve tried sanding a bit to get them more even, but I’m still struggling
Hi Ashley! Sorry to hear about the issue you are facing. Let's see if we can get this sorted out and fixed for you. First check to make sure the ends are alternating; each side piece should have one end grain exposed, and the other end grain covering the next piece. See 6:55 minutes into the video for the example. If the orientation of the sides are correct and you still have a gap issue, mark the piece(s) where the gaps are, and then stack ALL the pieces side by side to line up the double rabbet joints. By doing this, you can compare the cut dimensions, and the lengths. Hopefully this will reveal some cuts that can be fine tuned with some sanding. Give this a try and let me know if this helps you!
I keep having issues with either the top notch or the bottom notch being roughly 1/4” short and I’m not sure why. I double checked CL measurement. Any suggestions? Is this why you have 2 jigs?
Hi sugaslate. Most dimension issues point back to cutting the lumber: either on the line or on the wrong side of the line. Where to cut with respect to the line you draw is important and can get confusing. Remember to "cut away" the not needed wood and "cut to save" the wood that is needed.
I recommend making a template. I made two so I could see how the double rabbet joint fits together. Remember the template represents the lumber. Lines drawn with use of the template should be cut up the line's edge on the "save" lumber. Here is a link to a template video that may help you. czcams.com/video/x4J0TIL4Mcc/video.html
Hi Bobby! This may be a silly question. I know the arch was able to hold you up (which was awesome!), but do you think this arch could support a floral installation for 6-8 hours? Would making the base supports longer help increase stabilization so the arch wouldn't fall forward once the floral installation was attached? Thank you!
Hi Maddie! Supporting floral arrangements should not be a problem. See this one here: czcams.com/video/0MyPcRHUTsA/video.html
You can certainly make longer supports if that helps you. The base support length I selected is a good compromise between support needed and avoiding potential trip hazards with longer base supports. Good Luck!
@@doitstepbystep3376 Thank you so much!
Shout out to The Citadel shirt at the 6:55 mark! Go Dogs! '16
Sic'em Dogs!
When you cut the 8' boards in half, do you do a 30 degree cut if you have a miter saw and then cut your rabbit?
Yes if you want to maximize the length.
Awesome video. Wondering what length/brand screws you use for the arch? Appreciate the video!
Thank you for your comments! Since I used soft pine wood, I chose the zinc coated (indoor use) 2-1/2” Kreg pocket hole screws for soft wood👍🏽
Hi there I am making one of these arches for a wedding would you be able to tell me what size pocket screws did you use thank you
Do it Step by Step
Thank you for your comments! I used soft pine wood, so I chose the zinc coated (indoor use) 2-1/2” Kreg pocket hole screws for soft wood👍🏽Good luck with your project!
Thoughts on doing this out of 2x4s instead of 2x6s? I don't need to be able to hang from it, haha.
2x4's should work fine, just make sure your math is correct for the 2x4s. In this video: czcams.com/video/x4J0TIL4Mcc/video.html I show how to measure for 1x4s, so it will help you with the 2x4.
Just be aware that the proportions may look a little thin if you use 8' lumber cut down to ~4' sides. Good luck and have fun!
Hi! I found your video because I'm attempting to make a hexagonal trellis very much like this. Can I use these same joints with 4x4s?
I think it is possible with the right tools and skills. The difficult part, at least for me, would be getting a deep enough cut with the saw(s). My circular saw, and jigsaw would not be able to handle nearly 4" deep cut. A hand saw could do it, but require skill and patiences to get "square" cuts. Good luck with your project!!
Also, before you drop $$ on a lot of lumber, find some scrap pieces of 4x4 to practice on.👍
If you need to cut the bottom out of one, what can support it?
I'm not sure I understand your question correctly. You can send me a sketch or picture at doitstepbystep@gmail.com so I can better understand. Thanks!
I need help with that join I cut my 2 x 6 with a 30° can I still do the rabbit join on it?
If I read your comment correctly, the answer is yes. If you can send me a picture of your 2x6 at doitstepbystep@gmail.com and maybe explain your question in more detail, I can help you salvage your 2x6.
Question please 🙋🏼♀️ What kind of and size of screws did you use to join it together?
Do it Step by Step
3 days ago
Since I used soft pine wood, I chose the zinc coated (indoor use) 2-1/2” Kreg pocket hole screws for soft wood
Are there any downsides to using pressure treated lumber or is that just as good as "kiln dried"?
Price. When I built the hexagon, PT lumber was more expensive than kiln dried. PT wood should be a strong lumber and a great choice.
Hi , sorry if this questions been answered. The pocket holes, what distance and length screws did you use please :)
Hi Benjamin. I used 2-1/2” Kreg pocket hole screws for soft wood). Please check the video at the 7:10 mark for the pocket hole instructions. Good luck!
What is the approximate interior height? Would someone who is 6ft tall hit their head on the top piece?
Great question. The answer is a 6' tall person will not hit the top piece. I'm am not sure of the overall inside height, but there is a picture in this video czcams.com/video/0MyPcRHUTsA/video.html of the wedding party, and the Minister and the Groom are 6'3" and 6'2" respectively.
Hi Bobby if you are still checking comments I’m trying to make the template and I’m missing something because the pieces are not fitting together. Can you provide some instructions for that? Also, Once you have the template you just used a circular saw to cut the pieces?
Hi Katrynah. Have you seen this video? czcams.com/video/x4J0TIL4Mcc/video.html
First, verify the width of your lumber. If it is 5.5", then the distance from each side to the middle should be 2.75"
If that is correct, then measure from each side to the center of the double rabbet joint. Each side for each piece should be 2.75". If it is not, then the saw blade cut on the wrong side of the drawn centerline.
If each piece of lumber measures 2.75" from side to center, then that is good.
Now measure the three rabbet joint cut lines. They should be equal to each other. For a 5.5" width, it should be 3 3/16". At least by my tape measure it was.
Let me know how the measurement checks out.
I used a circular saw to cut most of the line, and then finished with a jigsaw.
Thank you! I am 1/2 way through the build. I am not see the length for the base support.
Hi Shawn! Around the 2 minute mark, I mention that each base is 2 feet long. Also, I created another video showing more of the measuring details for the base supports.
czcams.com/video/uI_W-wOX4lU/video.html
I hope this helps. Good luck!
Any recommendations on the size screw to use ?
Thank you for your comments! Since I used soft pine wood, I chose the zinc coated (indoor use) 2-1/2” Kreg pocket hole screws for soft wood👍🏽
@@doitstepbystep3376 Great! Thank you for the help
Wer can i get those folding work tables
I believe I bought those 5 or 6 years ago from either Costco or BJ's warehouse.
Hey Bobby can I use a 2×4×8 to do the job
Yes, you can! The measurements for the joints will be different but they are determined the same way. Here is a link for a 1x4 template. czcams.com/video/x4J0TIL4Mcc/video.html
Same width as a 2x4! Hope it helps.
What size pocket screw did you use?
2-1/2” Kreg pocket hole screws for soft wood
Can you please provide a printable template or instructions re how to make the template. I watched the other video you did on making a template but it was a template for 2X4 and not for 2X6. Thanks!
Hi. Sorry about not seeing your comment earlier. I haven't thought about a printable template before and it might be helpful. I've check into it, and from what I understand, printers vary on how accurate they print and you might be better off measuring directly on the lumber.
Can you sale a MDF, cardboard, or even just paper template?
Did you ever make a printable template? In watching the video, the center of the wood is found and two 30 degree angled cuts are made. I will try to make one today, I would appreciate it if you checked it.
Can you unfold this For easy transport to venue ?
At the beginning and end of this video czcams.com/video/pownFIMcDho/video.html you can see the hexagon in pieces, and in a semi assembled state. If you have room to transport the arch semi assembled, you can do it!
What size/length screws do I use?
Since I used soft pine wood, I chose the zinc coated (indoor use) 2-1/2” Kreg pocket hole screws for soft wood
Hello, is this arch knockdownable?
Absolutely! Please see this video: czcams.com/video/pownFIMcDho/video.html
How many 2x6x8 boards are needed?
4 boards. More info is at 90 seconds into the video.
What screws were used?
Since I used soft pine wood, I chose the zinc coated (indoor use) 2-1/2” Kreg pocket hole screws for soft wood
How much it cost to make this hexagon?
Lumber was less expensive when I designed and built the arch in 2020. I spent approximately $65 USD for lumber.
is there printable template ?
I do not have one, but I did make a video on how to make the template: czcams.com/video/x4J0TIL4Mcc/video.html
What's the length of each segment?
Each piece is 47.75". When assembled, a "side" is almost 51". This is because when one piece is fastened together to another piece, a side is "extended" 3 3/16". I hope that makes sense.
@@doitstepbystep3376 got it, so three 2x6x8’s will be needed 👍🏻
@@shawnpemrick4303 I used four total. The forth is so I could make the base. Bonus was it left me with a 4' 2x6 just in case I had to remake a piece/section.
Aren't the interior angles of a hexagon equal to 720, not 360?
If it is 720, I guess I got lucky!
What is the finished size? Height and width?
6'11" tall, 8' wide. There is a picture in this video czcams.com/video/0MyPcRHUTsA/video.html of the wedding party, and the Minister and the Groom are 6'3" and 6'2" respectively.
Spertinya tinggi hexagonal lebih kecil arau tdk sm dng lebarnya. Akan mnyulitkn hexsgnl yg sdh jd krna mmkan tmpat. Cb yg knockdown
Brother: Blessing to you, when GOD give detail to Moses to do the Menorah Hebrew candle lights the foundation of the Menorah is a hexagon. So when you build this shape you calling for GOD Blessing.
Thank you for blessing me with your knowledge! All glory to Him from all blessings flow.
Brother let me tell you another information. Way is the Star of DAVID is power in it??? Because the inside of the Star is the hexagon is the foundation of the Menorah given in detail to Moses.