Just did this.. it takes 8 screws and no need to remove the charging port. In my case the battery was swollen so I did not need to see half of this video about removing the back cover :)
@@kamrannagi3044 you can use the second half of the video. I used some old plastic cards to lift the battery out but this is crazy wel glued in place. Be careful of the ribbon connector that goes over the battery, if your afraid of ripping it you better follow the video guide and remove the lower part as well. After removing the battery it started to boil again by itself so be careful!! Toss it outside or is a salt bath and dispose of as chemical waste.
Dude! This video was great! Helped me find a loose ribbon cable that just had to be clicked in and my phone worked again! Your wonderful step by step instructions gave me the confidence to go at the job.
@@3picninjaboy The adhesive and plastic will start to desintegrate, most plastics never boil, they burn before. Additionally electronics in phones are not made to withstand temperatures this high, like the flash which should never ever be heated above 60°C or else it may loose data or just die
Thanks for this video. I was able to replace my swollen battery, the second time this happened on two different make. I think Huawei has a battery swelling problem. Just a suggestion, you may like to include a count of the screws required to be removed from the bottom charging port and the top, motherboard.
Thanks for this Video! It encouraged me to replace the battery myself. And yep I succeeded! The biggest challenge was to open the back cover because I only had a hair dryer and did not dare to make the lid really hot.
Thanks, I followed the instruction to replace my battery swelling and it worked but it was really hard to remove the battery. I used an electric oven as a heater. Smok came out from the swelled battery, so I get rid of it quickly.
Why did you remove the copper colored LCD flex cable? Doesn't look like it impedes the removal of the battery at all. Just for safety since it looks like it's attached to the motherboard?
I mean, do you really need to remove the cover for the charging port and antenna? The battery does not seem to be covered by the antenna and you could just flex the flexkable up a but when removing the battery, right?
You are lucky. I tried. There is a plastic film under the glass that came apart, then the glass broke. I wish they would still use good old-fashioned screws to open it for a simple task as changing the battery.
First of all get a new sticker. Last step is always to stick back panel PROPERLY back because of 2 reasons. 1st if you are just taking back back panel like this it is even falling off after a certain time 2. handset is definitely not waterproof any more this way which is one of the advantages of the phone
unfortunately I can't open back cover, I heated it on a hot plate in different time/temperature combinations Despite use of appropriate suction cup, there was not even a small gap between two parts of phone.
bro could u share how did u actually open the back cover? i am having a hard time to open them. i have all the neccessary equipment and all...heat gun, prying tools...but it did not even have any opening when i use the suction...and it became really hot and i am just afraid the heat would damage other parts in the phone itself...the temperature is like really hot till i need to use cloth to hold the phone, yeah it is that hot...LoL...
Went to a shop and they said there was 85% chance of glass breaking in process of taking back off. Don't know which method they intended to use but it put me off going ahead with battery replacement. Will live with 60% battery capacity for now. Still lasts a day most days.
They make it so hard because THEY DON"T WANT YOU to be able to replace the battery and make your phone last another year or two. THEY WANT YOU to buy a new fucking phone. Try finding a smartphone with a removable battery nowadays. They dont want your stuff to last. They want you spending money.
@@theycallmekowalski this is not a manufacturers' exploit though, it is about the market. Stupid people want their phones to be slim but the next day they they will buy a thick silicone case because slim doesnt hold well in hand as well as the need for additional protection. However, for the design to be slim, the manufacturers are forced to use adhesive tapes instead of metal casings and screws etc which would otherwise thicken the phone no more than a silicone case. Remember when iphone released their first slim aspect ratio screen (18:9), people got so crazy about it that every manufacturer followed virtually killing the better 16:9 in every respect in a very short time. It is not always manufacturers fault... the mate 10 pro is a still good example of the above trend which people discarded though the manufacturers would have prefered to keep it out for I suppose economic reasons - I mean, a mini jack port - once they realised the lack of it hits the sales charts, the jack port returned where it should be in newer models - so again - people decided.
Hi, I'm from Mexico and I have this cell phone, I need to get the battery and I can't get it here, could you give me a contact and see if you can get it for me, I would appreciate it
Just did this.. it takes 8 screws and no need to remove the charging port. In my case the battery was swollen so I did not need to see half of this video about removing the back cover :)
Hey man, my cover came off too because of the swollen battery. Could you please tell me how did you replace your battery. I'm a complete novice.
@@kamrannagi3044 you can use the second half of the video. I used some old plastic cards to lift the battery out but this is crazy wel glued in place. Be careful of the ribbon connector that goes over the battery, if your afraid of ripping it you better follow the video guide and remove the lower part as well. After removing the battery it started to boil again by itself so be careful!! Toss it outside or is a salt bath and dispose of as chemical waste.
I've removed all the screws after finished asked by myself, why😅
Worked perfectly, was a little bit hard to actually take out the battery cause I only had a hair dryer, but at the end everything worked just fine.
Dude! This video was great! Helped me find a loose ribbon cable that just had to be clicked in and my phone worked again! Your wonderful step by step instructions gave me the confidence to go at the job.
110 degrees celcius, that is a 110 fahrenheit my guy. 110 celcius will fry your phone.
Why would it?
@@3picninjaboy 100 degrees celcius is boiling temperature so it would be really hot.
@@Allan_1462 I know. But its the boiling point of water things like adhesives, plastics etc. have a much higher one.
@@3picninjaboy The adhesive and plastic will start to desintegrate, most plastics never boil, they burn before. Additionally electronics in phones are not made to withstand temperatures this high, like the flash which should never ever be heated above 60°C or else it may loose data or just die
You're the man. I couldn't have found out how to replace it by myself. I've done it easy as pie thanks to you. Thank you so much.
😅
11.00 dollars for the batery and tools and my phone is like new. THANK YOU!!
Thanks for this video. I was able to replace my swollen battery, the second time this happened on two different make. I think Huawei has a battery swelling problem.
Just a suggestion, you may like to include a count of the screws required to be removed from the bottom charging port and the top, motherboard.
Thanks for this Video! It encouraged me to replace the battery myself. And yep I succeeded! The biggest challenge was to open the back cover because I only had a hair dryer and did not dare to make the lid really hot.
great video ! i was able to replace my swollen battery and now my phone is as good as new!!! Thanks a lot
Thanks, I followed the instruction to replace my battery swelling and it worked but it was really hard to remove the battery. I used an electric oven as a heater. Smok came out from the swelled battery, so I get rid of it quickly.
Why did you remove the copper colored LCD flex cable? Doesn't look like it impedes the removal of the battery at all. Just for safety since it looks like it's attached to the motherboard?
Changed my battery using this video, great job and a working phone again 👍
Thank you for the video, it is well done and helped me a lot. saved a lot of money. Wishing you all the best from luxembourg.
I mean, do you really need to remove the cover for the charging port and antenna? The battery does not seem to be covered by the antenna and you could just flex the flexkable up a but when removing the battery, right?
It helped a lot!! Thanks for sharing knowledge!!
Did you have to apply new adhesive to the phone to close it? it doesn't show you did, but other videos show adhesive being reapplied
Don't you need to reglue the cover or heat it again when reattaching it to the phone??
yeah I was also thinking about this...
You are lucky. I tried. There is a plastic film under the glass that came apart, then the glass broke. I wish they would still use good old-fashioned screws to open it for a simple task as changing the battery.
Is it this phone still waterproof after battery replacement?
definitely not anymore. not unless you put a new one
Thanks Serg. Worked like a charm :-)
Where did you get your battery? I can't find an OEM one.
Thanks you very much, battery replaced!
First of all get a new sticker. Last step is always to stick back panel PROPERLY back because of 2 reasons. 1st if you are just taking back back panel like this it is even falling off after a certain time 2. handset is definitely not waterproof any more this way which is one of the advantages of the phone
can you recommend where to get parts like a battery, a new sticker and what glue to reattach the back cover?
Thank you very much i was about to pay somebody to do it for me but with this video was so easy :D
unfortunately I can't open back cover, I heated it on a hot plate in different time/temperature combinations
Despite use of appropriate suction cup, there was not even a small gap between two parts of phone.
bro could u share how did u actually open the back cover? i am having a hard time to open them. i have all the neccessary equipment and all...heat gun, prying tools...but it did not even have any opening when i use the suction...and it became really hot and i am just afraid the heat would damage other parts in the phone itself...the temperature is like really hot till i need to use cloth to hold the phone, yeah it is that hot...LoL...
Sehr Gut Danke
Hey is huawei mate 10pro battery different to huawei mate 10 ?
Do u know if the mate 10 pro battery is exactly the same model as the mate 10 lite?? Thanks!!!
ringing problem after battery replacement. I need help.
Hey Serg, do you have a good supplier for the green spudgers you use? they are my go-to, but they are hard to get.
Can we this battery for mate 10 lite ? I think the size is same
what screwdriver did you use?
grazie ottimo tutorial,seguito alla perfezione tutto ok
amazing video thank you so much bro !
Huawei Mate10 pro is explode when battery is going high?
thank you very much ! May God bless you
Thank you very much, dude!!!
super vid, thanks a lot.
excellent
New video. I need a part I can not locate. I have a Samsung s2 tablet.the part i need is the protective backing.do you deal in parts?
where are the imei on the phone? can you help me? on hardware?
The question is where did you find an original Huawei battery?
Went to a shop and they said there was 85% chance of glass breaking in process of taking back off. Don't know which method they intended to use but it put me off going ahead with battery replacement. Will live with 60% battery capacity for now. Still lasts a day most days.
I buy original battery and replaced it but its still draining much battery what i do please help
Maybe you have applications that use a lot battery
sir i want to change my huawei mate 10 lite battery so which battery i have to purchase what is battery number
HB356687ECW
thanks mate
mate 10lite battery 🔋 4000mh??????
ans the screen?
Tq i made it 🥰
eh yeah if my battery dies I think I'll just leave it to someone else xD I'm really bad with these small screws and parts
why the engineer want make the battery so hard to remove?
Purposely make things unfriendly to make job opportunity for phone shop.
They make it so hard because THEY DON"T WANT YOU to be able to replace the battery and make your phone last another year or two. THEY WANT YOU to buy a new fucking phone. Try finding a smartphone with a removable battery nowadays. They dont want your stuff to last. They want you spending money.
@@theycallmekowalski this is not a manufacturers' exploit though, it is about the market. Stupid people want their phones to be slim but the next day they they will buy a thick silicone case because slim doesnt hold well in hand as well as the need for additional protection. However, for the design to be slim, the manufacturers are forced to use adhesive tapes instead of metal casings and screws etc which would otherwise thicken the phone no more than a silicone case. Remember when iphone released their first slim aspect ratio screen (18:9), people got so crazy about it that every manufacturer followed virtually killing the better 16:9 in every respect in a very short time. It is not always manufacturers fault... the mate 10 pro is a still good example of the above trend which people discarded though the manufacturers would have prefered to keep it out for I suppose economic reasons - I mean, a mini jack port - once they realised the lack of it hits the sales charts, the jack port returned where it should be in newer models - so again - people decided.
@@pawelw.9172 stupid people allright
where to buy new battery except amazon?
ifixit if it still helps you
I doubt it'll be the same after this...
Thnx!!!!!
Nice Dear
If you wait long enough you battery will get swollen and you can skip step one :D
thanks ! you are awesome! (I really need to get another phone though 😂)
My mate 10 still not charging after replacing port. Any ideas?
Battery
@@Studiotek Hi, I changed the battery yesterday. Got the same issue cannot charge at all...Did you have the same issue? Thanks!
am from Pakistan i need original Huawei mate pro battery plz
Serg this Sam wow !!
Errrr, repair shop it is then. Bit too fiddly for me 😭
My phone is like these phone put they open and close only idont no way.!
Hi, I'm from Mexico and I have this cell phone, I need to get the battery and I can't get it here, could you give me a contact and see if you can get it for me, I would appreciate it
hopefully the same phone I ordered is dead when I get it cuz the battery is swollen bad the back is already coming up.
That must be a new phone. Its totally impossible to remove the backside on my 1½ year old Huawei Mate 10 Pro.
wait until the battery swells... it wil come off by itself.
@@pawelw.9172 😂😂👍
Better not to buy this shite!
Thats your mothers reaction when she saw you