Bless up. Homie you just saved me. My girlfriend needs my car for a road test and they won't her use it if the abs light is on. The restart worked. May you have all the blessings in life.
got in my boosted 2000 honda civic 4 door this evening an randomly the abs light was on, im gonna get it inspected tmrw, an i thought to just give this a try, an ir 100% worked, im so thankful and grateful for your video it just saaved me a bunch of time an it guaranteed me to pass the vehicle inspection tmrw, your a legend my dude
Thank you so much! Had a dead battery on my 2012 Pilot and after jumping it, both the ABS/VPS lights stayed on. So I knew it was a glitch. Tried several suggestions. Your's was the only one that worked. I've heard of people having to pay upwards of $50 to reset it. What a scam.
If you have an active ABS code, the ABS light will begin to blink. The blinking frequency of the ABS light will indicate which code has been stored. Long blinks equal 10 and short blinks equal 1. An example of this would be three long blinks followed by one short blink. That would indicate ABS code 31. RF = Right Front LF = Left Front RR = Right Rear LR = Left Rear Codes: 11 = RF wheel sensor. (open/short to body ground/short to power) 12 = Faulty RF wheel sensor pulse signal. 13 = LF wheel sensor. (open/short to body ground/short to power) 14 = Faulty LF wheel sensor pulse signal. 15 = RR wheel sensor. (open/short to body ground/short to power) 16 = Faulty RR wheel sensor pulse signal. 17 = LR wheel sensor. (open/short to body ground/short to power) 18 = Faulty LR wheel sensor pulse signal. 21 = Continuous operation. (chipped pulsar) 31 = Solenoid 32 = Solenoid 33 = Solenoid 34 = Solenoid 35 = Solenoid 36 = Solenoid 37 = Solenoid 38 = Solenoid 51 = Motor lock. 52 = Motor stuck off. 53 = Motor stuck on. 54 = Main relay stuck off. 61 = Ignition voltage. 81 = CPU (Central Processing Unit)
Just want to say this worked on my 2000 honda accord v6 coupe in turning off the light. However the light did come back on almost right away b/c the new sensors I installed myself were not generating voltage, or so I thought. Once i fixed that (I had to reposition the new sensors a little due to the rust and the less than clean hole) the light went off by itself in like 10 seconds of driving. The sensor tip needed to be VERY close to the reluctor ring. I was hand turning the hub/bearing (wheel is off at the moment) while trying to get a voltage reading on my multimeter. Once I got a reading I tightened the bolt good and buttoned everything up and the light went off auto! Those other youtube videos failed to mention that you really should check resistance and voltage before putting everything back or that ABS light won't go away and you'll incorrectly think the new sensors were defective. PS if after doing this and your ABS light does go away but you notice your ABS activating under 10MPH as you slow down, then for sure your ABS wheel sensors are not generating any if much voltage. Lastly I TU and SUBBED this video bc his method worked as intended. If the light came back on , it is not his fault. Just means you've got an underlying issue, probably with the sensors.
Gracias, pude reparar un Accord 2002. La ficha es azul, tiene dos cables y no esta conectada a nada. Debajo del volante. Esa misma ficha da lista de errores con luz. Segui tus pasos para el ABS y me fue bien. Abrazo !!
dude thank you so much! dealer was such pricks about turning opff the stupid abs light after I changed my suspension and most likely damaged one of the sensors. idc lol ill pump the brakes manually. the lights are so annoying though. you're awesome!!
my engine light, abs light, and vsa light turned off it worked but once I left to the store with in 15 seconds they all turn back on I drive a 2010 honda Accord v6 any clue what to do next?
I have a 2006 UK-spec Honda Jazz (aka "Fit"). The ABS light came on after hitting a loose rock on the road (no damage to the wheel at all). Both my old and new OBD2 scanners report "No Codes". I tried your method: 1. Turn Ignition OFF. 2. Join pins 4 & 9 of OBD2 socket 3. Hold Brake pedal down 4. Turn Ignition to ON (not start engine) 5. ABS light illuminates... but the ABS light does not then go off for me. I tried pulling the 7.5A ABS fuse for a minute then replacing it but it made no difference. Any ideas?
Dziękuje kolego. Problem usunięty w hrv ’99 👌pozdrawiam. (W hondzie hrv ‚99 nie ma złącza obd , jest natomiast niebieska złączka 3pin i 2 pin i to ją mostkujemy. Następnie postępujemy tak jak w filmie wyżej i problem zanika )
Alexander van Loon you might how to change out your abs module if it continue to stay on have you changed all your abs sensors or had your abs sensors checked out
Awesome video man! Anyone with a Honda Odyssey 2011 who is dealing with this. Do as shown. Make sure foot is on brake before key is turned. Takes some screwing around with but will work. Light might blink more than usual
This procedure did not work on my 2005 Honda Accord. The ABS light did not go off when I turned the ignition switch with foot on brake pedal,, it just stayed on. Further,more after removing the jumper wire, the starter would crank, but the car would not start. Apparently the jumper wire between the pin holes shorted something out or blew a fuse. Please advise how to repair whatever it damaged. Thanks.
Have a year 2000 civic se.The small estate version.Not sure where to put the wires?.Also my mate said he could plug his little computor into it to reset ,but im not sure where to plug it in too .Thanks.
I have question I have 2013 honda civic ex and I was driving car and at the same time all the lights came on. abs,vsa,power steering, brake light can't figure it out you have any suggestions instead of dealership. Thanks
Stupid question but, what kind of wire is that? What would I even look up to find something like that? Does it come as a part of a multimeter set or something?
Probably too late now but to answer your question the reason probably is your cars ABS system is holding more then one code for a fault so you probably fixed one problem but another still is in the system somewhere
@@flaboi404 Thanks heaps. So steps you just mentioned in above comment are the steps before running through process in the above video? Thanks again..
My 99 crv threw a abs light randomly and it’s not starting, cranks but won’t start going to try this. Hopefully this works. Going to try a different tranny speed sensor then new front abs speed sensors. My Speedo jumps speed erratically and randomly, also has a code for the front abs speed sensors
My 2000 Honda Civic B18c4 comes on the abs goes off sometimes mechanic couldn’t find the plug too diagnose as it appears too be missing or re loacted it can go off long enough too pass its mot ) ( yearly inspection here in uk itll fail with abs on))
Hi dude, dose't work in my honda jazz...i've abs and vsa lights on. When i did your treeck pin 4 and 9 him, i turn on acc and light abs flash few times, disapeer, and flash again ..
How are you Las time I changed my front wheel bearing on my 2008 ODYSSEY but the sensors was stuck so I cut it and put 2 new sensor and now the abs light is on I don't know why if sensor are New
Bless up. Homie you just saved me. My girlfriend needs my car for a road test and they won't her use it if the abs light is on. The restart worked. May you have all the blessings in life.
Oliam you welcome
got in my boosted 2000 honda civic 4 door this evening an randomly the abs light was on, im gonna get it inspected tmrw, an i thought to just give this a try, an ir 100% worked, im so thankful and grateful for your video it just saaved me a bunch of time an it guaranteed me to pass the vehicle inspection tmrw, your a legend my dude
Good man tried it on my 2006 accord worked perfect i will say a special prayer for you tonight God Bless
randolf hearst thanks
Thank you so much! Had a dead battery on my 2012 Pilot and after jumping it, both the ABS/VPS lights stayed on. So I knew it was a glitch. Tried several suggestions. Your's was the only one that worked. I've heard of people having to pay upwards of $50 to reset it. What a scam.
you welcome im happy it work out for you
This worked for my 2000 Honda Accord V6 EX; I used a paper clip instead of wire.
Worked for my 2005 Honda Element. Saved me a ton of money.
I just tried it on my 07 Element, didn’t work.
If you have an active ABS code, the ABS light will begin to blink. The blinking frequency of the ABS light will indicate which code has been stored.
Long blinks equal 10 and short blinks equal 1. An example of this would be three long blinks followed by one short blink. That would indicate ABS code 31.
RF = Right Front
LF = Left Front
RR = Right Rear
LR = Left Rear
Codes:
11 = RF wheel sensor. (open/short to body ground/short to power)
12 = Faulty RF wheel sensor pulse signal.
13 = LF wheel sensor. (open/short to body ground/short to power)
14 = Faulty LF wheel sensor pulse signal.
15 = RR wheel sensor. (open/short to body ground/short to power)
16 = Faulty RR wheel sensor pulse signal.
17 = LR wheel sensor. (open/short to body ground/short to power)
18 = Faulty LR wheel sensor pulse signal.
21 = Continuous operation. (chipped pulsar)
31 = Solenoid
32 = Solenoid
33 = Solenoid
34 = Solenoid
35 = Solenoid
36 = Solenoid
37 = Solenoid
38 = Solenoid
51 = Motor lock.
52 = Motor stuck off.
53 = Motor stuck on.
54 = Main relay stuck off.
61 = Ignition voltage.
81 = CPU (Central Processing Unit)
This was helpful for me. Ive gotten a 13 potentially. Just gotta find a way to fix it now
Thanks man! This video is clutch for visual learners like myself
Just want to say this worked on my 2000 honda accord v6 coupe in turning off the light. However the light did come back on almost right away b/c the new sensors I installed myself were not generating voltage, or so I thought. Once i fixed that (I had to reposition the new sensors a little due to the rust and the less than clean hole) the light went off by itself in like 10 seconds of driving. The sensor tip needed to be VERY close to the reluctor ring. I was hand turning the hub/bearing (wheel is off at the moment) while trying to get a voltage reading on my multimeter. Once I got a reading I tightened the bolt good and buttoned everything up and the light went off auto! Those other youtube videos failed to mention that you really should check resistance and voltage before putting everything back or that ABS light won't go away and you'll incorrectly think the new sensors were defective.
PS if after doing this and your ABS light does go away but you notice your ABS activating under 10MPH as you slow down, then for sure your ABS wheel sensors are not generating any if much voltage. Lastly I TU and SUBBED this video bc his method worked as intended. If the light came back on , it is not his fault. Just means you've got an underlying issue, probably with the sensors.
W comment
Gracias, pude reparar un Accord 2002. La ficha es azul, tiene dos cables y no esta conectada a nada. Debajo del volante.
Esa misma ficha da lista de errores con luz. Segui tus pasos para el ABS y me fue bien. Abrazo !!
Ósea puenteaste ese mismo arnés?? El azul que dices
Thank you Sir! You just saved me $7000 :) Who do I make the check payable to? LOL You're the best
dude thank you so much! dealer was such pricks about turning opff the stupid abs light after I changed my suspension and most likely damaged one of the sensors. idc lol ill pump the brakes manually. the lights are so annoying though. you're awesome!!
Straight to the point and 100% accurate thank you.
you welcome
I guess I'm kinda randomly asking but do anyone know of a good place to stream new series online?
my engine light, abs light, and vsa light turned off it worked but once I left to the store with in 15 seconds they all turn back on I drive a 2010 honda Accord v6 any clue what to do next?
I just did it and it worked. Thanks brother.
you welcome
Brother thank you so much this was a life saver shop wanted to replace all kinds of stuff
you welcome
I have a 2006 UK-spec Honda Jazz (aka "Fit").
The ABS light came on after hitting a loose rock on the road (no damage to the wheel at all).
Both my old and new OBD2 scanners report "No Codes".
I tried your method:
1. Turn Ignition OFF.
2. Join pins 4 & 9 of OBD2 socket
3. Hold Brake pedal down
4. Turn Ignition to ON (not start engine)
5. ABS light illuminates...
but the ABS light does not then go off for me.
I tried pulling the 7.5A ABS fuse for a minute then replacing it but it made no difference.
Any ideas?
Thank you man. This working for my 2008 honda accord.
Thank you so much - it worked exactly like you said - installed wire in port 4 and 9 and done in less than 2 minutes - thanks
💯
Thank you! Going to try this and see if it works for me. Will update once that happens. Thanks for the straight forward and helpful vid.
Did it ever happen
This worked on my Honda accord 2008 thank you so much 🔥💯
💯💯
Is this only working with Japan made Hondas?
I have a UK built CR-V 2002 and no reaction at all to the abs light with papeclip in pin 4 and 9.. :(
Thank you very much!!!! Just did it and it worked like a charm!!! Can’t thank you enough.
Dziękuje kolego. Problem usunięty w hrv ’99 👌pozdrawiam.
(W hondzie hrv ‚99 nie ma złącza obd , jest natomiast niebieska złączka 3pin i 2 pin i to ją mostkujemy. Następnie postępujemy tak jak w filmie
wyżej i problem zanika )
My hero💪 I swapped my abs sensor and was losing my sheeeit
💯happy i can help
Thanks for posting this tip. Everything worked fine EXCEPT that the ABS light continued to stay on. Alas.
Alexander van Loon you might how to change out your abs module if it continue to stay on have you changed all your abs sensors or had your abs sensors checked out
Appreciate the suggestions. Turns out one of the ABS sensors had failed, causing the problem. Thanks for the help.
Alexander van Loon you welcome
Awesome video man! Anyone with a Honda Odyssey 2011 who is dealing with this. Do as shown. Make sure foot is on brake before key is turned. Takes some screwing around with but will work. Light might blink more than usual
Did it stay off for good and what kind of wire did you use
I can't find that connectors. Box on my 2001 acura I have the abs light on
Does it stay off
Lifesaver worked a treat, thanks for sharing your knowledge
Aaron Rempala yu welcome
Bro I can’t wait to try this, do you need to put a new and sensor in for this to work??
Organized Chaos no nothing but a wire Or a paper clip
Thanks for the video easy & quickly
Thank you . 2006 crv lights off. Thank you again.
You a life saver bro!!! It worked for me.
Ray Santiago yu welcome
Dose it really work I have a 2017 honda accord ammo try it later
Awesome! Thanks bro! 👊💥🔥
Just like that, thanks! Peace to you my friend 🙏
I’ve got a ? O course. Abs on 06 crv brinks 3x and doesn’t hold. My VSA is also on with the triangle light. Any help is appreciated.
By doing this does the brakes still work properly? does anyone know?Thank you
Right that’s what I wanna figure out 😂😂
Well, this is just to reset the abs light, assuming you already fixed the issue with your abs
I tried many times exactly the way you instructed. It blinked twice but the abs light is still on. Accord 2003
I’ve got a 2008 CRV. Will this work. ABS and VSA light still on after changing the correct ABS sensor that the diagnostic reader gave me?
This procedure did not work on my 2005 Honda Accord. The ABS light did not go off when I turned the ignition switch with foot on brake pedal,, it just stayed on. Further,more after removing the jumper wire, the starter would crank, but the car would not start. Apparently the jumper wire between the pin holes shorted something out or blew a fuse. Please advise how to repair whatever it damaged. Thanks.
Have a year 2000 civic se.The small estate version.Not sure where to put the wires?.Also my mate said he could plug his little computor into it to reset ,but im not sure where to plug it in too .Thanks.
I have question I have 2013 honda civic ex and I was driving car and at the same time all the lights came on. abs,vsa,power steering, brake light can't figure it out you have any suggestions instead of dealership. Thanks
Thanks for the help, very clear instructions
I have a 06 Civic is this the same procedure that you know how?
Mine flashes 3 times and doesn't turn off. I have the wire connected correctly into the OBD-II port. Any ideas as to what is going on?
Same happens to me just now. Any fix yet?
mine flashed 3xs as well will try change my ABS parts
Thanks my brotha worked for me ,
Thanks man, its work👍❤️🌷
Stupid question but, what kind of wire is that? What would I even look up to find something like that? Does it come as a part of a multimeter set or something?
can used any wire
Hey buddy i changed my abs cord out also, i did the steps you provided the abs light flashed twice but remained on. What would make it do that?
Mr Thomas You might need a ABS module
Probably too late now but to answer your question the reason probably is your cars ABS system is holding more then one code for a fault so you probably fixed one problem but another still is in the system somewhere
I did everything like in the video.. lights flashes but it still stays on
If this does not work any other solution? 2011 Accord Traction control is also lit up with my ABS light. Help!
He calls it a C Connector, not the OBD port 1996 behind the ash’ tray?
Thanks alot very helpful!!!!!
Thanks for the video.. Any ideas on how to get ABS light off on a 1995 Honda Legend?
Unplug the brake module on the hood first for 10 minutes and then disconnect the battery for 1min ... i do them all the time on the 95 and under
@@flaboi404 Thanks heaps. So steps you just mentioned in above comment are the steps before running through process in the above video? Thanks again..
Will this work on a honda crx delsol 1997??
My 99 crv threw a abs light randomly and it’s not starting, cranks but won’t start going to try this. Hopefully this works. Going to try a different tranny speed sensor then new front abs speed sensors. My Speedo jumps speed erratically and randomly, also has a code for the front abs speed sensors
I WAS CONFUSE it only have 8 holes I was looking for the 9th hole and never found it loll but it does works
Thanks a lot,you saved much
I have 95 Accord how you do there?
I was driving today and the light just came on, can this hack help me or? Thank u
Thank you so much you’re good man
My 2000 Honda Civic B18c4 comes on the abs goes off sometimes mechanic couldn’t find the plug too diagnose as it appears too be missing or re loacted it can go off long enough too pass its mot ) ( yearly inspection here in uk itll fail with abs on))
Thank you buddy much appreciate it help me 🏆
My light blinked 3xs. Any idea why? I recently replaced my rf sensor and my light is still on and obd is not reading the current speed on that sensor
Same. I replaced all of my sensors, but the abs light flashes 3x and stays on...
Sorry he doesn’t answer questions
Great video thanks, I just had this light turn on and replaced the sensor couldn't get the light off until now. Awesome job👍
Eli A yu welcome
If is flashing 3 times and stay on what is to be done?
Hi dude, dose't work in my honda jazz...i've abs and vsa lights on. When i did your treeck pin 4 and 9 him, i turn on acc and light abs flash few times, disapeer, and flash again ..
what year is it
Thanks a lot. Worked like a charm.
Aliyu Yakubu yu welcome
How are you Las time I changed my front wheel bearing on my 2008 ODYSSEY but the sensors was stuck so I cut it and put 2 new sensor and now the abs light is on I don't know why if sensor are New
Do you know how to do this for a 95 honda accord? I'd really appreciate the help!
Hey Man.. awesome video, but may i know what is the name of the 4th and 9th pin? I m afraid mine would be different pin position.
Thanks. I have a honda accord 2000 but doesn't mark the seat belt light
Awesome fix my 99 accord v6.
Did the light stay off? I have a 99 Accord v6
@@nanobot81 yes
Thanks a million..👌🏾
My 2001 acura cl type s has the abs light on and can't find the box for the ports to connect the wire can somebody help
My abs light keeps coming back on after i clear. Think it could be a sensor or something?
Corey Ray it could be a sensor. Have someone read the codes and get it fix. It should go away after
The light comes on because you need a fix.. not because you need to reset it again
Thanks bro!! It works.
Dose it work for 2001 honda civic?
This man is a hero
Worked on 1998 Honda Accord 🤙🤙
Will this work on a 2011 Honda accord?
Thank you!!
The abs light is on with vsa light too, I proced to do in your video and really abs is off now, but vsa continues on, do you know why ?
Cesar de Leon Try to get a new vsa button
Works perfectly
What do you do if you can't find the port I've checked everywhere
Thanks a lot bro
Mines is still on…it just blinks repeatedly. What should I do?
Will 16 gauge piece of copper wire work?
Will it work for a 13 model
Gracias funciono para un honda accord 2002
I have the same issue with my Honda Accord I tried this but my abs comes back on after starting I do have a tcs light on would that affect it ?
need get all new abs sen then it go off
Thanks in a big way
dude you FN rock thank you
adrian valdez yu welcome
Thank you so much for this 💕
Can do this on Accord G9?
Thanks bruh🙌🏾🙌🏾 back in business 🙌🏾
It don't work at all there is nothing connected to pin 9. Pin 9 on the obd connection is blank. And pin 4 is ground.
Thanks for the vid
works!! thanks
All hero’s don’t wear capes