2006-2012 Mercedes Benz Transmission Control Module Unlocking and Adaptation Still No Reverse No ...
Vložit
- čas přidán 4. 03. 2022
- If you need parts or accessories for your Mercedes Benz click link below:
Mercedes Repair Info
www.startekinfo.com/
Mercedes Parts
amzn.to/3S0Z11y
Mercedes Accessories
amzn.to/3HDdFY6
Exellent😊
Salam,yes sir,I have c200k 2009model, I change supercharger and boots sensor mass sensor,still no boots coming
رَبّـ❤ـيٌ يزيدك ويرزقك لان عربي محد يدعمه .
Thank you for your videos. What was the solution for this issue?
they replaced the transmission with used one now it has to be programmed
@@BestCarFixes is it just electric kit or the whole transmission anyway?
I think it's the whole gearbox
can you clone a isu ?
Hey wea are you located i need your help
P1925 I think this trouble code is stopping my car from starting casterly cranks but no spark and I'm getting gas
My car move but won't shift gears Automatic shift gear just had Major tune up and top off with check engine light on had diagnostic said shift gear sensor issue
Any update on this mate ?
I think this fault is from the Inteligente servo module (ISM) and also there is a relay in charge of the ism if it loses steady current it can cause this .
Thanks Alot i will chek and let you know
@@BestCarFixes okay sir
Hi can you tell me where the relay would be locators at?
check ignition swich (gateway)
Sir try manual shift the gear from neutral to reverse
You need put the scn number and the ehs number
Hello, Is it possible with the help of AUTEL 608 PRO to Erase and Learning the Gearbox on Mercedes W212, 2015 , 722.996 VIN : WDD2120061B148466 ? Thank you.
yes if you have the old one
@@BestCarFixes How do you know if it's old or new?
How can i contact you sir ?
I have a no crank start problem the fault code:
P1925 Drive authorisation has been refused by control module N15/5 esm
Any advice?
see if you can communicate with esm module
@@BestCarFixes I tested can hi and can lo on can bus c the voltage was perfect but on can b when asleep it wouldn't give me a reading? awake can hi was 0.72v and can lo was 4.4v
Mouhamad it need programing
And scn coding correct
P1925 Drive authorized refused by the control module
I am Mechanic in the Dubai you need 15 years experience
HI
السلام عليكم هل حليت هاي المشكله واذا تنزل فيدو الحل
fix my car please merc c class need you expertise mate
Boss can i have your number to ask a question?
the module was not programmed correctly. you have to do an initial startup on a virginized unit or it will not drive and the module is useless. Also if it was a used unit you have to use a new virginized unit. then you can program it.
Ok
I did some of the used tcm from the same car and it work fine
Hi, I changed the TCU unit and there is this error code - The start enable signal was not issued by the control module drive authorization system. When I checked there is VIN mismatch on TCU/ECU. Car is 2016 c300 4m equipped with VGS4 tcu version. Can IM608 or MS919 help me write the correct VIN on the tcu? Thanks
Hi can you please suggest how to fix error code p0606 component y3/8n4 fully integrated transmission control unit is faulty. Can i service or have to replace the sparepart ?
most of the time code p0606 is software related
see if an upgrade can fix it or get next one
@@BestCarFixes hi thanks for your advice
Hi
I'm from India can I get your whatsaap number.
I held the gas down 15 seconds on start no idle position or position start 1
Diagnose and see what. Codes are you getting
@@BestCarFixes Fault code 2768 component Y3/8N2(internal speed sensor VGS) is defective and Fault code 2*** signal for Y3/8N2 not sure I think it was a repeat code paper faded on physical report. Report date 8/30/22 model E350 Mercedes Benz yr 2007
At this time 8/30/22 vehicle battery replacement
Diagnostic cost 500 dollars how can I do this what devices do I need for phone devices
استاذي ممكن رقم جوالك اتواصل معك
PLS NUMBER