IM608 Pro | How To Virginize and Code A Used Engine Control Unit A 2007 Mercedes Benz S Class
Vložit
- čas přidán 2. 07. 2024
- Hey Guys
Today I am going to teach you how to virgin / renew a used engine control module on a 2007 Mercedes Benz S Class with the IM608 Pro
In this presentation you will learn:
1.All the tools necessary to do this procedure
2.. Common terms that you will familiarize yourself with this procedure
3. The Location of the Engine Control unit
4. See the proper bench setup
5. See the exact set by step process on how to virginize and write the VIN on the used ECU with the im608
This is an easy service that you can start promoting for this year's make a model. Just think about how much would it cost to send this to a dealer? You could charge 200-300 USD for this procedure.
I hope get inspired apply what you learned today!
www.auteltech.co.za
Slow and clear explanation.
Really good video.
Thank you!!!.
Thanks for a great video; your presentations are absolutely brillant, simple, clear and concise as well as informative;
Im glad i came accross this. I actually performed this task upon brainstorming about the logical ways i could implement it.
Your process is absolutely smoother. I did it all manually in the immo section of the tool.
Since i was at the vehicle at first,
I read engine ECU data as well as coding data and saved both of them.
Then home office bench set up to renew the module just like you did.
Next, i wrote the engine EXU data previously saved by obd
Then wrote the VIN
Then wrote the coding
Then personalized the ECU; this is basically the transfer of antitheft data including key number and ID from the original to the donor
Activation is not allowed on bench and must be done by obd so i did.
After that i went into diagnostic to check the DAS. All 4 requirements were YES, TP detached, start enable & the first 2 that i cant recall.
For me the module was ready to rock n roll; it did not start because the vehicle had a preexisting condition that supposedly blew the original ECU per an alledged electrician say.
I believe either, the original ECU was misdiagnosed and wrongly accused of being bad, or the causes of the ECU becoming bad, if it is, is still present as evident by 2 low voltage active dtcs.
The client refused to pay for my service; i just told him to have a more competent electrician perform a disgnostic because i knew i made the donor ECU as identical as the original including the number of keys and their key id.
Thank you for an easy and understandable description.
Much appreciated 🙏🏽
So happy I found this channel. New sub for sure. Learning my 608 pro as fast as possible
Hi Curtis I am Ulrich from Congo I'm very excited the way u explaining yr training course makes me I understand everything clear, I am a student still, and yr training making me to understand many things from im608, when I'm going to be ready I will order a better tool from u Mr thanks so much kindness, I will always follow yr training courses until I get there
Love your videos man I been watching them all
As always very professional! Thanks
How are you doing Mr. Curtis? This is The Jack I just now Virginize my first ECU Mercedes. I input the Vin number and everything went beautiful. Bought the ECM from eBay, dude I was so excited I need to order one more key so I can go to the car and do the Engine learning procedure. Your client, Volley.
Hey Volley, This is wonderful news my friend. Your becoming a diagnostic "beast"! Keep up the great work
great job curtis very detail
I am very grateful for your excellent tutorial GOD bless you THANK YOU very much
Thank you brother. I hope you can help your customer with this training. Thanks!
Great video, as always!
Thanks so much. Im glad you enjoyed it! Take Care
Great video!!!!
Hi, like your teaching
Thanks for the video it really help
Glad it helped
Awesome job brother
Thanks 👍 I appreciate your support
Hi Curtis! Can you make a video of programing a rear Sam module with 909 tablet please! Thanks from Puerto Rico.
another thing to remember is that for item number 3 there is a difference between right and write:) but seriously this is the best video I’ve watched about reprogramming a mercedes ECU yet. I noticed another person had commented about asking if they needed the original ECU for information. He brought up a good point because every online service I see that offers to clone your original ECU to new donor ECU requires both ECU’s to be sent and if the original ECU was damaged and cant be read you’re required to send the EIS and your key with your donor ECU. Can you please clarify whether or not you need to read any information from the original ECU and then transfer it to the donor ECU or is it just like the video shows and all you need to do is insert the Vin number? 17:25
Great presentation as always . I see the J2534 is required for this operation . Will other non-autel J2534 devices work as substitute in process? and if its only the Autel J2534 that works , will it work with the IM508 ?
Good to know...thank you!!
Thank you for you online training, very interesting, I have to buy my 608 for sure
Hey Filex, Justa purchasing tip. If you don't need any training or support you can purchase any ware online. If want training and support I can sell the tool to you directly. Im just giving you this option because alot of people get inspired to by this tool , but then after they buy it the get stuck or they are afraid to do the procedure. If they would have got consulted first and then I sell them the tool i would be able to help them out that situation.
@@AutelConsultancy thank you for your response, I have this question, can I start doing something like this and programming keys if I start with the 508 model and then down the road upgrade to the 608 ?
@@AutelConsultancy I am a 30 year experience tech with European cars but want to get into the business of ecu programming , immo and keys
@@felixmasis3658 If your serious and want me to help you acquire new skill sets as well that will help you make this transmission , go to auteltech.co.za and book the diagnostic tool consultation.
@@felixmasis3658 Book a consultation with me my friend. If I give you a tool strategy with out consulting you then it will be costly since I have ran my framework to find out all the problems you want to solve
Thank you sir for the vedio. Learning.
My question is ( Do you not have to clone the data from the original ecu, so that you learn it to the donor ecu?
Hi Curtis, do you do 1 to 1 training? I'm trying to find a reputable company to learn how to do eeprom work and I'm finding it difficult but your videos are clear and consise. Would it be an hourly rate?
Hello Curtis, Thanks a lot for the procedures. A lot more videos or renewing DMEs are available but not in that simple terms.
I realized in the video the year models were up to 2012 on the S Class. In case the DME / ECU job is for 2013- / newer Merc models, can IM608 help? If not what other tools can help for such scenarios? Can the IM608 perform the teach in procedures for newer model Mercs?
Thank you for a good work.please can you show me how to program a used 2015 evoque transmission control module.
Thanks for the information, but I didn't see where you load the original ECU information in the donor, did you transfer it through the tech-in via EZS?
thanks for sharing
Great content Curtis! I just found your content today and will definitely be watching all of your videos. I understand that you charge for your time however maybe you could give me a tip or possibly pay you for your services if needed? I have a MK906 pro (Subscription expired) hat I tried to code out rear o2 sensors on a CLS55 (off road vehicle) and found myself with ESP issues and lack of communication with modules. My question is, is there any way to correct this easily with the tool? Maybe do the teach in process to correct it? I reverted the settings however the issue still remains. I also have an IM508 that has a current subscription. Any pointers would be great. Thanks!
Great Video.. May I ask you if an Autel DS808 can be used to viginised a Shifter Module DSM from Mercedes Benz. Thanks
Making alot sense
thank you for the video. question, am i plugging in the IM608 via the vehicle's OBDII after the ECM is reinstalled to complete drive authorization steps?
thank . it would also be nice to show an example of replacing and adapting the electronic board of the Mercedes gearbox.
If I am able to help one of my clients doing that procedure Ill record it and share it with everyone.
Awesome. how do i use my IM608 to program a used ecu (same part number) on a mitsu outlander 2018 that has a no start problem? have also bought a used ETACS. Vehicle key is the blade type
I had to replace the ECU in my e-Class recently and came across this issue of not being able to fit a 'used' ECU from another car. I would be interested to know what people should be charging for virginising Mercedes ECUs so they can be used again? I solved the problem by moving the eeprom from my old ECU to the new one. I de-soldered the immobiliser chip and physically moved it into the replacement ECU. Worked fine.
Very good
When you are good you good 👍 👍 👍 thumbs up
You are very clever .
Hi my good friend, I really enjoyed the video but I got a question still, please what is the PROGRAMMING/CODING option actually used for
Hello, I found out a lot from your videos, I have IM508. I have a question, what could you recommend as a voltage backup for bmw encoding that need 13V? Regards
Awesome
Hello,
Thanks for the video. Can IM 608 do the same with other car brands? Thank you
I am new to using used module, so I may have missed something. What about the software and coding for the particular car that that module is going into? Doesn't it have to be corrected? Thank you for your videos!
Wow…. I used this IM608 for 2 years ,using these Benz function numerous times and till now …..you guys comes up with this tutorial… I reckon Autel Tutors really need to keep up the pace of releasing new contents regarding to those new updates.
As 99% of that time…. We have to figured it out by ourselves 😂
Nice job though , this machine works really well in both key making and diagnosis
Just for clarification, I dont work for Autel.( Im private) This is a sample of what I provide to my clients but I wanted to share this with the community as they are not able to get this level of training from Autel .
Launch pad is better in doing this
@@johnbosco2404 Every tool has its perks. You just have to find one that gives amazing support and helps you get results your looking for.
I always enjoy videos, very knowledgeable tech guy, I can vouch for that as you would help me out in the past when purchasing my autel from you,, but one question will the ultra do the same here as the IM 608
Hi Scott. I hope your doing well. The ultra doesnt have the Im608 immo functions. You would need to use the im508 and G-box to do the renew process of the ECU and the Write Vin. Then you can use the Ultras do the teach in authorization procedure .
@@AutelConsultancy thanks,, I know anytime I have a question like that you can always find answer
Hi boss just a quick question On the im608 tool does it program with all the modules on the Mercedes.. I’m looking for the right tool
Good work from keep it up from George
Thanks for the detailed video, does 508 also have teach in drive authorisation
Yes
Wowww very good can autel im608 benz transmission used ecu chang and program ?
Love this video! Can a BCM be Virginize.
Nice
Hi Curtis , is autel able to do teach Authorisation on W212 , CRD3.1 ECU ? ECLASS 2012
Hi Mr Curtis- if I purchase a g-box3, would I still be able to perform the same process?
I have im508 with gbox2 and xp400pro, can the “teach and drive” process be done with my set up?
Thankx
Have a question Curtis is this procedure available on a 97 E320 or have to send it out to get it wiped cleaned
Great class as usual Curtis can I use the 508 for this procedure
Yes, absolutely! You can do the bench procedure with your IM508 and gbox2 then the coding procedure "Teach in drive authorization " with your elite
Will this process work without the g-box?
Is the process similar with ABS unit?
Is the access log in pin free provided you have active subscription?
Lastly, is the process similar for a VW?
Regards
Hi Curtis, I need help with W204 ABS coding using the Im608
Hi Curtis. I bought the im608 pro from AESwave and then I came across your channel. I want to learn everything this tool is capable of. My question is can I still get a consultation from you or am I ineligible because I bought it from another distributor?
HI Sefo You can book a diagnostic tool consultation with me at auteltech.co.za . Some of my clients who also saw my video when it was too late usually end up sending there tool back and then later purchasing it from me. This way they have access to me on a long term basis and they can truly benefit from their tool
Can the IM608 Pro also program an Mercedes Benz TCU
hello brother.
I want to learn the process step by step of changing and copying data TCU gear Mercedes Benz .
with the IM608pro.
Thank you.
Ihave done this with my IM608 pro . the ECU worked in the car but it got a lot of communication issues ,ABS/ESB is inoperative light is on. i couldn't do online programming as the scn coding fails after the programming is done on my tool . any idea?
Hi Curtis
Great video, thanks
What the difference between the IM608 and the IM508?
The im508 is for people who already have a good diagnostic scanner and just need key coding capabilities. The im508 has a basic level of diagnostic software on it . The Im608 Pro is for people who want diagnostic capabilities, j2534 flash programming capabilities and locksmith level key coding capabilities.
Got a question I have a autel maxicom mk908 pro and want to virginize and code a 08 mercades cl550 I want to know if it’s even possible I saw you do it with the im608 but my tool is having a problem with the program log and said it sent it to autel but the tech support lady is clueless and can’t even answer my question thanks
Great video. Been looking for the autel product that would do this, hope you are doing well my friend.
Maybe we can do another chat soon?
Lou
Hey Lou. Thanks for compliment. Yes , I think you have my details still? To make it easier you can book an existing client session at a time thats good for you. Thanks
Does 608 have possibility to connect to Dodge Grand Caravan ECU?
Hey sir, can I carry on this same process on TCM programming
Hi, have recently arrived on your video. Can this be done on mercedes ME2.7.2? For 2007 w221 S Class with M275 Engine.
Hello can I used these tools for a 2004 s230 mercedes
Thanks for sharing your valued knowledge Curtis. I am in Australia (RHD) and have a 2005 Mercedes CLK500 C209. The ECU and SAM have been water damaged. I have purchased used units with the same codes. Could you please advise the procedure to clone them to the vehicle? If too involved online or payment is required, I could contact you directly or can provide my contact details. Regards, Graeme
One vedio used transmition vergine and program benz s class
Great Video my brother. I have a Mercedes Benz SLK 350 2005 with. abad modlule and thee shop wants to charge me $2,000.00 with ordering a new module from Mercedes Benz. I am a computer Tech but I have never considered working on car computers. Thank You soo much for the info.
You have an advatantage. I just consulted a robot engineer yesterday. After consulting him I should him how to use his skillset to the automotive niche as most mechanics are not software savvy
Thank you for the information. I just have one question. If they send you the ECU how do you complete the job after renewal and writing of the ECU? Dont you have to have access to the vehicle to complete the job? It looks like you have to be with the vehicle to complete the process. Just a little clarification is needed on that process. Thank you
Yes you would need access to complete the job. They would have to clear the ecu for you and send it back. That’s when you have to do the drivers authorization yourself with a scan tool
Can you programming a 2000 ML320 ecu w/ mcu Motorola b58289 E428b mask
Curtis many many thanks for your precise explanations and instructions sir. Can this procedure be done with im508, xp400 and gbox2? (Without j2534)
Yes it will. The Im508 with the xp400 Pro will give you the same key coding coverage as the IM608 PRO
@@AutelConsultancyThank you
We truly appreciate the time and effort you sacrifice to help us get the best use of our tools. I specifically purchased this to make Mercedes keys and virginize ISM and transmission control modules. I made the mistake of buying im508 before seeing your videos. Can't wait for xp400 so i can utilize the INVALUABLE information you teach in your videos to earn extra cash. I'm interested in your consultancy, just to show gratitude ( because I've learned all i need to know from your impeccably made videos.) THANK YOU THANK YOU SIR
Tanx sir I appreciate your support sir
Do you need to pay subscription (or be online ) to do virgin ? Please advise
A lot of customers like to bargain on Japanese and some domestics cars and I don't good business. I have im508 and xp400pro. Trying looking into specializing in European cars, not easy, but slowly learning.
You should get a mentor. This way I shorten your learning curve and you will get the information you need quicker. Otherwise it will take longer to learn and you might be less confident to take on certain jobs.
@@AutelConsultancy Agree. It is overwhelming to learn with so many different car models and their technology.
Hello, Where can I get that DB15 cable?
Is im608 same as Maxisys IM in the uk ?
Hey thanks for the Video
I have an issue with a Mercedes E300 2014
The Power Electronics Unit has failed basically the Hybrid motor for generating electricity, A new unit is £4,000 +
I can get a used unit with Guarantee the for like £500 but have been told it needs Virginizeing before it can be Used
I guess exactly as this procedure for the Mercedes ECU
I am in the UK any idea of people or places I could try to assist me
Best Regards
Did you reset a used one?
can this be done without the im608?
Can the im508 do something like this 😫
Hi, can you utilize the MS919 to virganize a used ECU or you need this specific scanner?
Thanks in advance!
You would would need a different tool to do this procedure. If you need help figuring out which way to go to auteltech.co.za and click the diagnostic tool consultation service
Can a new ecu be cloned?
Please can you tell me if Autel 608 and mk 808 have similar features? And does the mk 808 can diagnose vehicle from year 2000?
Hi Guerra. I hope you doing well. If your serious want want me to align you with the right tool you should book an appointment with me at auteltech.co.za and click the diagnostic tool consultation. Its going to take me 45 minutes for me to run my framework and explain the limitations of each tool. Alternatively if you dont want certainty you can all Autel new York
Can the unit do the same for the trans control unit I see way more used trans swaps than the ME thanks
Yes, ive done quite a few with my clients
Hi
I had to replace ECU the n my w220 2006 ,and now question is can it be coded/programmed with AUTEL MaxiSys 2 elite
Please advice how to
Thanks Gab
If its a used one your tool doesnt have the capability to virginize the module. If its a new one then you should be able to program it. Send your supplier the VIN number to make sure you can program year vehicle. This is what I do for my client just to make sure their tool can program the module.
Does anyone in the Dallas -Ft. Worth area have this devise? The Dealer told me my car, 2004 ML350, can not be fixed. The AAM went out and is now obsolete. Does anyone know a work a round because these computer are specific to each car and you can not substitute used parts. Great body , tires, interior, I need help!?
Is it possible to do this procedure with the IM508 with xp400 pro? I don't have gbox2 or jvci adapter.
Yes ive done it with the Xp400.
How to renew w204 sim271de2.0 ??
I just get the new IM608 Pro II but when I try to writing the VIN for 07 S550 and the said this unit does not support writing VIN.... ? cold you help. please
Did you check with your supplier first? I can help you but I charge for customers who I didnt sell to. Im not even sure if the function is available. Maybe give your supplier the VIN and see if they have access to the engineer to verify the function . This is what I recommend my clients before they attempt a procedure.
question, can you reset or virginlize a Mercedes Benz 2005 SLK 350? I was told by a shop it can't be done and that I need to buy a new one for $1,000.00. I think it can be done because why would it work on an S Class and not the SLK Class?
Usually what I do for my prospective clients is when I talk with them in my consultations what I will do is find out the VIN and ECU information to get a 100 percent answer. If you dont want to book a consultation you can try asking the supplier who you want to purchase from and see if they can give you that information before you buy.
Hello, pls can dis renew the ECU offline?
Can the im508 virginize ecu?
Hello Curtis. This is Kelvin. I recently swapped out an engine and transmission in my 2008 clk 550. Initially, it wouldn’t start but after placing the old ecu on the replaced engine, the vehicle cranked. Unfortunately, it will not move. Is it as simple as programming the ecu that came with the swapped engine or do I need to have the replaced transmission programmed all together? Any advice would be greatly appreciated.
Which tools do you have?
@@AutelConsultancy when I said, "I recently swapped," I didn't mean I did it. A friend of mine who is a mechanic performed the swap. He does not work on Mercedes and this part has been a challenge. I'll have to ask him about the scan tools and accessories he has. Should I ask him about some specific tools?
I don't mind so much paying MB for the new ECM or module, whatever I may need. I just refuse to let the crooks in the service dept. touch anything I own ever again. NOT just MB either, any dealer, as I've yet to find an honest dealership.
This is off topic of the video but I was thinking on purchasing AUTEL MS906TS MAXISYS I would like to learn more about it I seen it online it was listed around $1,350 I was kinda interested. Anything I should know about or where I can purchase it?
HI Marvin, I charge for this information as it takes about an hour to diagnose and educate the client about the everything they should know . The problem of self diagnosing your self is that most of the problems/limitations of the tool your only going to find out after you purchase. Also you have the challenge of verifying if your tool is going to be a usa model or an international model. You also are not going to have a solution to reduce our update fees . You lso need to consider the year this tool was made as maybe there is a replacement for it. Buying a diagnostic tool is like getting married... You dont want to get it wrong the first time as you might have alot of extra baggage. If its worth it to you , you should get consulted first in my opinion.
@@AutelConsultancy how much u charge for the consultation?
@@marvin2977 97 USD. In most cases it saves the client 2000 usd in cost
Buenas,,, mi nombre es Gercy,, y quiero saber si venden el im autel 608
Can we do this on autel maxisys ultra?
I dont think so
Can this be done with an autel elite 2?
Hi Adrian , Im afraid not. There is no immo function for Euro vehicles on the elite.
i have autel 506 and autel j2534 box.can i reprogram mercedez benz car?
If you have the Im508 and j2534 you will wont be able reprogram the Mercedes benz because the im508 has a basic level of diagnostic software and it doesnt have access to online servers.
I have a IM608 and gbox