Fender Stratocaster Install Curtis Novak P.U
Vložit
- čas přidán 18. 09. 2020
- I installed a Curtis Novak pickup on a friend's Stratocaster that I had previously refinished.
• Fender Mexico Stratoca...
The front and center pickups were installed with lace sensor pickups.
Then I replaced the pegs, filled the peg holes for replacement, made the back panel, replaced the frets, modified the fretboard, changed the fretboard R, made the nut, bent and rewired the calm, etc.
The Curtis Novak pickup looks like a humbucker, but it is a single coil pickup. The model is a Gold Foil: GT-V Vintage correct classic Tokyo Style Gold Foil.
www.curtisnovak.com/shop/gold...
At first I didn't want to ask if I could put this pickup on... but I bought it. I bought this pickup.
Furthermore, the race sensor is combined with a race sensor...what will happen?
To be honest, I was worried about it, but I didn't feel comfortable with it. Is it blended? I think.
There's definitely a lo-fi feel to it, but it's there. I think it's possible.
But I wanted to use the round head screw because the mounting holes of the TOKYO pickup have a good hole for M3 screws.
But I couldn't find a good round head M3 screw, and the wood used to hold the Strat's screw is very thin.
So I made this part out of brass. I thought it would be a good idea because it would fit in nicely and I could make use of the lathe, lol.
Replacing the rotomatic type pegs with Crewson type pegs is a bit of a pain.
The conversion bushings make it a little easier, but I didn't want to do it this time, because I didn't want to. It's going to look a little different.
I took a method of filling the peg holes with maple.
Normally, I would have filled the holes with a round bar and re-drilled them later, but I took the method of drilling the holes in the round bar from the beginning. (I have a lathe, so I felt I could get better accuracy that way.)
Maple for easy round bars? I'm glad I bought a lathe so I could make it! I think.
The frets are Freedom's 07 Speedy.
The sound that the owner is looking for is the sound that looks good on the rhythm guitar or cutting, so I chose it.
The guitar that the owner can play is an SG, and when he played the SG after playing a Strat, he felt it was easier to play.
He felt it was easier to play when he played the Strat and the SG. So I changed the R on the fingerboard to 12R.
I was quite satisfied with the fretwork. Maybe it's my first time to do so.
I was able to reconfirm the accuracy of the fretboard correction and the accuracy of the fretboard R.
He also sent me a video of him playing the fretboard.
It's still difficult to confirm whether the lefty is completely playable or not.
The string height is set high, so we set it to a setting that we think is easy to play, and then the owner will have to check it for himself.
I wonder if this is what airplane instrumentation flight is like.
And the last song. It's an original composition by the owner of this guitar. I had it made!
I hope you enjoy it all the way through.
Thank you for your request.
Guitarist and BGMProject2 (Shunnosuke Kaneko) "Bar with Sherlock
/ syunnosukekaneko
/ @user-kh4ce5zx5m
Parts and tools used
TONE Power Grip Driver Set PLPGD6
amzn.to/2Q5MrRr
VESSEL Precision Hex Drivers
Set, amzn.to/2O6hFoC
1.27(inch) amzn.to/2X4xBvQ
1.5amzn.to/34KDAZs
Fret polishing 3M sponge polishing
320-600 amzn.to/2YC5c0k
800-1000 amzn.to/2JnIEd9
1200-1500 amzn.to/32iG29c
Metal polish is still Picard.
amzn.to/32Ip7f7
I like 3M masking tape, man. I recommend 6mm high frets on the guitar.
amzn.to/32H0gZ9
Dolmel 4000 Ruiter. Great torque, but hot! I can do a lot of things, so I'd like to be able to do 4,000 if I could.
amzn.to/2Kh3NH5
They have a new one called the 4300. If you can use the Stu-Mac base plate, this one might work too.
amzn.to/3712F48
3M body polishing compound, this is enough for a guitar.
amzn.to/34WHuhO
Plenty is good to have, orange English oil for the fretboard.
amzn.to/2Kh4G2n
This cross is tremendously good. Recommended. Seriously.
amzn.to/2PRUJM8
Website
pedaru.wixsite.com/andybassan...
Twitter
/ andybassguitar
Facebook
/ andybassguitar
Instagram
/ adachi_andy_koki
#Fender
#Andy_bass_and_guitar
#Restoration
#Fender
#Andy_bass_and_guitar
#Restoration - Hudba
That mount you fabricated for the Novak gold foil was truly inspired. Great work Andy!
Thank you Andy.... as always, it is a pleasure and honour to watch you work.
Gorgeous. Loved the sound, too.
例の旋盤クン いい相棒になってますねぇ。
いつもながらの 美しいフレットとナットは流石です！
丁寧な仕事を見られて 癒されましたわ！thank you‼
エンディング曲、素晴らしいネ！
You are a madman my friend! in a good way.
Thank you!
Beautiful. What knobs are these ?
Good job
Did you test the switching at the output jack with an ohm meter before you finished assembling?
Before installing the pickup, I checked the output and looked at the phase.
I did not try to measure the overall output.
It's good to check. I will do so in the future.
Couldn't you just have mounted the gold foil directly to the top of the pickguard?
What paste did you run on fretboard?
Original beeswax wax.
Wow 💥
get luckyカッコいいですなぁ
Ficou linda!
What's the product you use to hydrate de rosewood fretboard??
Homemade beeswax wax.
Andy do you use wood glue to set your nut? Amazing video as always!
I use a tight bond.
And super glue.
I saw this in the refinishing video too, why do you countersink the holes on the body/neck when the screw heads that require the countersinking dont make contact with the body or neck?
ボディの塗装を皿穴可能（面取り加工）するのはネジを外す際にネジと塗料が癒着して一緒に剥がれてしまうことがあるからです。
おそらくカスタムショップ系や、手の込んだギターの場合ほとんどが面取り加工をされていると思います。
@@Andybassguitar Very interesting, i learned something today. Thankyou!
The name of music on end of video?
I am searching the same.
Daft Punk - Get Lucky
@@CelikDogukan Daft Punk - Get Lucky
This is a great job
カスタムのペグ交換お願いする際は今回の様なブッシュでお願いしたいですねー
正直コンバージョンブッシュの方がコストパホーマンスは高いです。
見た目が同じならそっちのほうがおすすめといえばおすすめかもしれません。この方法は浪漫はありますが。
フラックスは何処の使ってますか？
これです。www.monotaro.com/g/01150695/
めっちゃカッケーほかに言葉が見つかりません
旋盤欲しいです
旋盤扱いが難しそうですな、、、フレットサイドに充填してるのはボンドと指板の削りカスですか？
サイドのは今回はパテを使いました。
正直パテのほうが使いやすいのでおすすめです。
コーヒーとか使う方もいらっしゃいますね。
Huh. Not sure I understand why you went to the trouble of hollowing out dowels on lathe to press in to tuner holes. It's way easier to glue in solid dowel then re-drill appropriate size hole. Anyway. Nice editing on these videos. The lighting is great.
I chose this method because I thought this method would be more accurate than that method.
Thanks.
👏🏽👏🏽👏🏽👏🏽👏🏽🎶🎸🎸🎵🥇🇧🇷🇧🇷🇧🇷
Yikes those knobs are obtrusive and ridiculous...not practical at all.
I rarely see people playing while turning the knobs these days.
It has a different knob now.
@@Andybassguitar I’ve seen you ‘play’ on your videos….trust me, we turn knobs while playing, and again you didn’t understand what I said… they stick out too high is all I said, and they really do, to each there own of course but, I see so many ridiculous gimmicks and impractical aesthetics. Believe me I deal with the same shit from people
Thank you for your comment.
I probably understand what you are trying to say.
From the point of view of ease of playing, it is also important that the knobs are easy to turn, and that they don't hit your hands when you play.
The knobs in the video were added after discussing with the owner about the importance of appearance.
The fact that the knob was changed soon after the owner played the guitar suggests that there must have been a problem. Or his taste has changed.
As far as playability is concerned, I think there are a lot of problems even with traditional guitars.
But it has become a tradition, and many users prefer it that way.
It's really up to each individual to decide what's better.