how thick is the plastic and how long did they last? Looks like it is getting dented with every short @3:20. And what if you hit the stem near the wire?
Thanks for your question. The plastic is a bit thicker than 1/4" / 6mm. And it held up pretty well, despite the dents. I switched over to pellets not long after making the video. Not as many dents. I have had a few shatter if you hit near the wire. It's definitely a weak point. After a couple of years, most of the spinners were trashed. I suspect the plastic was going bad, after untold years of being the sun before I got my hands on it. And the wood got a bit weathered and rotted. I consider a couple of years to be pretty good for this.
If you don't care about rotating anf just want hanging targets, you could just start with an empty milk crate or even a cardboard box laying on it's side, open face towards you. Then take any size target out of wood or snipped tin, drill 2 holes on top side by side and hang that target on the top of the open hole by 2 strings... Voila, your targets will face forward always because of the 2 strings. You could do the same with a tin can.
Thanks for showing this. Just made a similar one (using thin metal ...didn't have any plastic). its a great idea and a lot more fun than paper targets or cans you have to put back every time!
I have a couple pieces of a plastic cutting board leftover from another project. I think that could work with this idea. I could pick up another cutting board also
Love it, recycling and a fun end product. Maybe people could try a simple impact test with the material and gun they are going to use be for making this target set.
Nice target! Plastic is nice because it is quite lightweight. Even sweeter to lighten the lower target with another target on the upper side. Many airgun targets are so often "for use of pellets only" - just because of those darn ricochet BBs.. And I own so many BB pistols - that mostly are a bit less powered in comparison to the pellet pistols.
how thick is the plastic and how long did they last? Looks like it is getting dented with every short @3:20. And what if you hit the stem near the wire?
Thanks for your question. The plastic is a bit thicker than 1/4" / 6mm. And it held up pretty well, despite the dents. I switched over to pellets not long after making the video. Not as many dents. I have had a few shatter if you hit near the wire. It's definitely a weak point. After a couple of years, most of the spinners were trashed. I suspect the plastic was going bad, after untold years of being the sun before I got my hands on it. And the wood got a bit weathered and rotted. I consider a couple of years to be pretty good for this.
Looks good. Also props to you for reminding people of gun safety.
Super nice !! Like how they spin freely
That's a big part of the fun. You certainly know when you have a solid hit!
Great idea. Looks fun to build too. Thank you!
Nice job buddy. Thanks👍👍
Nice job and ready for fun!!. Thanks for share it.
Nice! Fun project, easy to understand and make. Probably better than one you can buy. Thanks.
This was AWESOME! Big thank you.
Thanks for watching!
If you don't care about rotating anf just want hanging targets, you could just start with an empty milk crate or even a cardboard box laying on it's side, open face towards you. Then take any size target out of wood or snipped tin, drill 2 holes on top side by side and hang that target on the top of the open hole by 2 strings... Voila, your targets will face forward always because of the 2 strings. You could do the same with a tin can.
this is awesome and will be perfect for me as i just started in the airsoft hobby
Amazing idea, thanks for the video!
You're welcome, Tim. Thank you for watching!
You are a good inventor
Thanks for showing this. Just made a similar one (using thin metal ...didn't have any plastic). its a great idea and a lot more fun than paper targets or cans you have to put back every time!
That's great! Glad it worked for you.
Just ordered the classic Daisy Red Ryder, and this is a perfect idea thank you 😊
That's great. Hope you have fun with it!
That's such an underrated rifle. Have fun cheers
I have a couple pieces of a plastic cutting board leftover from another project. I think that could work with this idea. I could pick up another cutting board also
As long as it's thick enough to drill for the pivot, I think you will be okay.
Awesome! Love ingenuity!
Thanks!
Brilliant idea
thanks for this info...i try to make one
You caught my attention with this plastic for plinking....
Love it, recycling and a fun end product. Maybe people could try a simple impact test with the material and gun they are going to use be for making this target set.
Excellent idea!
brilliant well done 👍🏻
Thanks very much and thanks for watching!
THOSE .....spin way better than the ones on Amazon !
Thanks!
Yea my air rifle would go straight through 😂
I'll see if I can come up with something more bulletproof!
That looks perfect for 1.77 bbs though amazing contraption 👍🏼
Nice target!
Plastic is nice because it is quite lightweight. Even sweeter to lighten the lower target with another target on the upper side. Many airgun targets are so often "for use of pellets only" - just because of those darn ricochet BBs.. And I own so many BB pistols - that mostly are a bit less powered in comparison to the pellet pistols.