How to Replace Your Hyundai Elantra Rear Panel
Vložit
- čas přidán 26. 08. 2024
- Check out my shop for all toolslinktr.ee/AUTO...
Today we have a Hyundai Elantra that's been rear ended in a collision. I'll be replacing the trunk lid, rear body panel and rear bumper cover. I'll take you through the whole autobody collision process of the repair.
As an Amazon Associate, I earn a small commission from qualifying purchases. Some of the links are affiliate links and if you decide to buy the tools through them I earn a tiny commission. It costs you nothing but helps me big time.
7 Piece Dura Block Sanding Kit:amzn.to/48xvNj3
Steck Quarter Panel Puller 20022:amzn.to/48NjvCJ
Astro Pneumatic Tool 930 Mini Reciprocating Air Sawamzn.to/41SYQeq
Sunex SX8200 Surface Blaster Kit:amzn.to/48J7Swz
The MAXI - 220v:www.dentfix.co...
Evercoat Rage OPTEX Color Changing Filler:amzn.to/3OhiHhR
Evercoat 425 Metal Glaze Ultra 30oz:amzn.to/492KXg7
Canadian Tool and Supply 7-Inch Air Angle:amzn.to/3tJ2zOQ
Wurth 1/4" ANGLED 90 DEGREE DIE GRINDER:shop.wurth.ca/...
Mirka MR-6 Finishing Sander:amzn.to/3vrjje5
Body Line Tool:amzn.to/3tNoZP1
Martin 1024 9" Blade Surfacing Spoon:amzn.to/3SbJ8I5
Uni spotter 5500:www.toolsource...
3M Belt Sander:amzn.to/48qO4hI
Milwaukee M12 FUEL 3/8 Stubby Impact:amzn.to/3H9va2V
Good job ❤
Just out of curiosity could you not have fixed the original panel or was it too much work
Not that it was too much work, but when the metal is kinked, you need to replace it.
It wouldn't crumple the same again and could potentially be dangerous in a future accident
@@AUTOBODYTECH how many hours do you need for this Kind of job? Exelent job.. I learn from every video ! Thanks
@ajlanda9661 if you have a spot welder, typically, they should take about 7 to 8 hours and maybe an hour or two for assembly.
The total job average pays the bodyman about 15 - 20 hours for something like this
yes , it's was repairable in about a third of the time allowed.
but he elected to change , his repair , his decision.
👏👏👏
Nice work man very professional. What is the black box you removed at 1:37 at the corner of the bumper? Never seen that part before on a car.
Thank you! It's a blind spot monitor system.
@@AUTOBODYTECH Oh I see, probably radar parts in that blind spot detection. Good thing they were not damaged, probably expensive!
yes quite expensive! after repairs they would need to be re calibrated as well.@@practicalguy973
Great job! Curious is there a way to remove the rear upper deck
lid trim For Hyundai Elantra 21-22 Hyundai to install the part 87390AA000?
It looks like you're referring to a deck lid spoiler? If yes, you would likely have to access the underside of the deck lid. More than likely, there are screws and clips attaching it to the deck lid
I did remove all screws but there still seems to be something else holding it (its not a spoiler, the part no. shows it as part of the trunk hood). Will try another method but am hoping not to break the glass since it's right next to it on this model SEL.
how much did that cost?
About 4000$
hey bro what disc do you use with your angle die
grinder
Hey, they are rapid strip disc. I've always called them a roloc wheel. Here is my Amazon link to something similar amzn.to/3wNKqRa
Do you have to add panel bond in between the new panel and old one? Where you will be welding?
Depends on the procedure. Every make and model is different. On this particular one, no.
Thanks! Just started doing heavy hits. I’m excited but nervous
@@ivanelgordov9099 nice! Hope these videos are helping!
What kind of chisel is that
It came in a 3 pack at home depot. Brand is anvil. They call it a pry bar