How to unlock Tamobyke Display Settings on V20 & V30 Movcan
Vložit
- čas přidán 17. 11. 2023
- Link to buy V30 amzn.to/3R4F1g6
Unlock settings and speed limit on TamoByke V20 & V30
#amazonfinds #ebikes #tamobyke
Link to buy storage bag: amzn.to/3R4F1g6
Chapters:
0:01 - Intro
0:10 - Unlock Speed
0:42 - remaining settings
2:22 cruise control
qmwheelscooter.com/
en.wikipedia.org/wiki/Electri...
FTC: Some of the products linked above use income earning auto affiliate links, which means that if you click one of the links and purchase a products, I could receive a very small commission (at no additional cost to you) - Auta a dopravní prostředky
![BRUTALLY HONEST REVIEW - Tamobyke V20 [What a Nightmare]](http://i.ytimg.com/vi/D57STRZX4qY/mqdefault.jpg)
Non zero start usually works with PAS only. It allows you to use the throttle in PAS only mode to get up to 8 or 10 kmh. Handy to get a quick start at a crossing / red light.
Interesting… i tried that didn’t seem to notice a difference both settings allowed me to get to 25 mph
I get my bike tomorrow can’t wait to set it up
Its a good choice
@@BRichSolution I definitely can’t wait
@@prettystud6014 How is the bike? Im thinking about copping this on payday
I have the single battery version v30. I try to increase the speed to 45 but it’s stuck at 40. Is there anything I can do for that?
Not sure… email Tamobyke and ask.
When the bike is on you can double tap the power button and it shows you a timer of how long you been using it since turned on if you do it again it shows another I think it shows the other if you have mph or kilometers press again and you back to distance
Good tip - double press power button once for time and 2nd time shows battery voltage
How do I reset po2 to factory reset I'm stuck in3 mode can't go to 5th mode at all
As seller or tamobyke for how to unlock PAS 0-3 to 0-5?
Do you know how to activate all the functions that are shown on the screen when you turn it on, such as the direction lights, etc., thank you
No. Doubt directional can display on screen as the wires do not interact with controller. turn signal switch wired to rear taillight and do not go thru controller
@@BRichSolution And then why do the icons appear on the screen? as well as the lights, among others
bcs its standardt
@@ernestosintjago3441
Did you get around to making any more videos of this bike?
Not much else I can do. Upgraded the suspension and brakes, Tampbyke refused to provide faster controller
i have the same v30 do you know any way so you can get your fat bike from 45 to 25 very quickly because in case of police saw us to make it 25km/h?
more Torque - Tamobyke V30 - 40 Amp controller
czcams.com/video/z6ZI-xXoLEs/video.html
@zabi4s From which site did you get the v30 and which country you from are you from the Netherlands?
Probably the factory reset option
I have a v20 and it maxes at 27 mph, ive gotten used to the speed and was wondering a way to make the bike faster, whether that be a new controller or something else
Need a new display which Tamobyke is sending me next week. I will post video if it works
@@BRichSolution please do a video on that and tell them to send you the correct P card because I actually have the new bike version of this. It has a H6CLCD screen it is beautiful. It is bright but the functions from this bike does not work for the functions on the bike that I have.the new screen Has 10 p functions. And my Bluetooth does not work on the new version of this bike. It’s not a QR code on the bike or anything so I’m interested in seeing a new screen for the version of bike that you currently have.
Anyone have the issue where p03 won’t switch modes? Parameters won’t stay put
Email manufacturer
Thank you for video maybe you can help me I am getting an error message on my display any suggestions
What error code?
Error E004
I oppened up the secret menu and found menu 9 and 10? do you know what these menus do. I just received this yesterday..
thanks
you will have to contact Tamobyke as both my bikes do not go past P08
Menu 09 should let you change de default pin code
pls help, how to change MPH to KPH on Amyet G60😭
Not sure i believe its hard codes with that controller. Not sure why this display doesn’t have settings menu. Reach out to Amyet or HappyRun to see if there is a way
Is there a function to somehow limit the speed of the throttle itself? It's legal here up to 6 km per hours but mine goes 25 km which is a problem
I don’t believe so. 6km is not that fast…i would just disable the throttle
my v20 not turn off after i press off button, only the screen is off but not a bike . any solution
Not sure
How do I reset on po2 reset I'm stuck in 3 mode
Not sure ask Tamobyke
why i got mode 3 only
See p03 setting at 1:10
how can i quickly set it back to 25 kilometer an hour
see video at 1:20
v30 is cool but one thing is accelaration not kind aggresive
Yes, acceleration seems a bit lackluster. Working on solution for that in the next few weeks
Is yours the 1000watt or the 1500watt version? @@BRichSolution
i put p04 on full and it’s still not working
Is p06 set to 2?
Can u explain p2 more
P02 if you set to 01 and then hold + and - it will reset bike to factory settings
I have v20 but with the different screen it is smaller but nothing works what ever I change
Does your v20 have the smaller 14Ah battery too? I think they made a cheaper version of the v20 to compete with Jansco X50
Dear, please contact your seller, only V20 sale in europe countries change the display because of speed limit policy.
Yes I am in Europe
@@BRichSolutionyes the same battery
@@Tamobyke-V20im not it europe and have the one with smaller display also and I'm now stuck in pas 3 only it won't let me change setting it wants me to input password and there is no way to switch to the next digit