Thanks so much for uploading this. I have a v6 and to make things interesting I am installing a grill and fog lights combo that mimicks the GTs. It involves removing the bumper so this was very very helpful. Nice video and very clear instructions.
i hit a coyote with my car and figured the work would be insane if i did it. so i got a quote to get it replaced. now that was insane. this sure helped a lot thank you!
So, I should be able to access my lower fog lights by just undoing the bottom splash guard? One of them has dimmed out so I need to replace them and I also want to add 2 more light bars to the rectangle slot underneath my fog lights. That all appears easily accessible once that huge splash guard is removed. Thanks for showing me how to remove that.
Do you have to do this to adjust the factory headlights.? My GT was in a collision and the dealer did not adjust after they repaired. I am getting stopped and flashed by oncoming traffic.
@happywrenching I know this video is a little old, but I just had my driver's side front bumper bumped haha, and the clips came out, that snapping sound when you are installing the corners under the headlights should this just snap into place like that once the splash guards and shrouds are tucked in the wheel well, mine aren't quite doing that so I'm probably lining it up incorrectly any tips you can give or advice would be great, good vid though, very helpful.
hello sir Hopefully you can help me quick, I am wanting to put a 2013 GT/ GT500 front bumper and headlights on my 2005-2009 GT, (change it from the newer look from the older look), I am just wondering if this would work given the year difference i.e change in headlights and bumper... thank you looking forward to the response!
Great video I was just about to change my lights on my "manstang" and stumbled across this video.. saves me a whole lot of money. Great job.! Bravo! Ty very much!
+eddie velasquez The process is similar in that there are clips for the radiator cover at the top, clips for the bottom cover, and screws in the wheel well. The location and number of clips and screws will be slightly different than what is in this video. You will still need to unhook the fog lamps, ambient air temp sensor, and side marker lamp plugs.
+eddie velasquez The process is similar in that there are clips for the radiator cover at the top, clips for the bottom cover, and screws in the wheel well. The location and number of clips and screws will be slightly different than what is in this video. You will still need to unhook the fog lamps, ambient air temp sensor, and side marker lamp plugs.
Today I backed out of a driveway with a steep curb and the bottom of the bumper cover hit and my passenger side of the bumper cover is popped out a little ( like at 5:14). I pushed it back on but the very corner ( like where your left hand is) stays stuck out some. It's cosmetic but it aggravates me bc I only have 3K miles on my car. What holds the very end of the cover on? Is it a clip that maybe broke? I can't tell by looking at it..
Oh yea i see.. I will have to look tomorrow when it's light out. I don't remember seeing that earlier when it was light out though. :( I guess I will have to get an entire new bumper cover all bc that one little piece is broken..ugh :(..Thanks for the quick reply though man.
hi i wanna thank u for showing this, im installing a 2013 mustang bumper cover on my 2011 mustang and im missing some parts now i know what they are, i also would love for u to show how the grill is installed because i have the grill but it just falls through the bumper cover there must be a support behind the grill could u show this i would really appreciate this, thank sincerely ryan
If I had the car I would definitely do a video but sadly I don't. However, there are many videos on grille installation so I'm sure you can find one that will help you.
Hey man throw back to when u wrote this post 7 years ago lol... Hopefully you can help me quick, I am wanting to put a 2013 GT/ GT500 front bumper and headlights on my 2005-2009 GT, (change it from the newer look from the older look), I am just wondering if this would work given the year difference i.e change in headlights and bumper... thank you looking forward to the response!
Literally struggling with ordering the right hardware from my not so local Ford deal, fml that they can’t even answer how many of each your car uses despite having a VIN.
Thanks so much for uploading this. I have a v6 and to make things interesting I am installing a grill and fog lights combo that mimicks the GTs. It involves removing the bumper so this was very very helpful. Nice video and very clear instructions.
I like the way you make a demo very clear audio and video. Thanks a lot.
Thanks for the vid..save me alot of money taking it to autobody shop to replace my bumper brackets..
@ 6:43 I thought the song "Ms. Jackson" by Outkast was about to start 😂😂
Very informative, helped me fix my bumper cover, thanks man!
Helped me change the ballast and headlight on my 14 mustang! Thank you!
Thanks for the video! My side bumper popped out abit for some odd reason. Thanks, again!
i hit a coyote with my car and figured the work would be insane if i did it. so i got a quote to get it replaced. now that was insane. this sure helped a lot thank you!
Best video on removing front bumper ! Great detail on everything !!! Thanks a million !
Thanks god this video is online! Thank you!
This is useful because the side clip isn't grabbing the bumper on the drivers side, going to take it off and fix it.
Would these steps also be the same for a 2010 mustang?
So, I should be able to access my lower fog lights by just undoing the bottom splash guard? One of them has dimmed out so I need to replace them and I also want to add 2 more light bars to the rectangle slot underneath my fog lights. That all appears easily accessible once that huge splash guard is removed. Thanks for showing me how to remove that.
Do you have to do this to adjust the factory headlights.? My GT was in a collision and the dealer did not adjust after they repaired. I am getting stopped and flashed by oncoming traffic.
@happywrenching I know this video is a little old, but I just had my driver's side front bumper bumped haha, and the clips came out, that snapping sound when you are installing the corners under the headlights should this just snap into place like that once the splash guards and shrouds are tucked in the wheel well, mine aren't quite doing that so I'm probably lining it up incorrectly any tips you can give or advice would be great, good vid though, very helpful.
Does the bumper have to be removed to replace the headlight bulbs in a 2014?
I want to replace my front and rear side marker lights. Can you do a video for that process please? Its for a 2014 mustang gt,5.0. Thanks chris
Hey how do you call the plastic thing that’s on the bumper reinforcements bar ?
My front left side bumper sticks out on the corner now . Cant seem to get that last clip connected . Any tips ?
Would this work on a 2012 mustang?
would this bumper fit the 2010 model ??
Thanks this helped a lot. Do you think you could do a video removing the hood?
will you be doing Side fender? :O
these videos are a huge help!
thanks for the uploads :D
My go to video. Thanks again
do the 13 headlights fit a 2012?
Dziękuję bardzo za bardzo pomocny film.
👍
Thanks so much is video help me out a lot I have a splashguard cover I need to replace and I could not figure out for the life of me what to do
Super good video thanks
where is the best place to buy a new bumper. I hit an armadillo and the bumper cracked from the drivers side. Thank you.
Well I'm guessing the armadillo was vulture food... after that. Poor armadillo..☠
CardID.com they'res are pretty reasonable and they get delivered pretty fast
I swear I hit one last Saturday tore my shit up radiator and condenser
Where do I get replacement screws ?
Does anyone know the part number or name for the bottom 2 bolts with the rectangle thing inside of the wheel well at 2:43 mark? I need to replace it.
hello sir Hopefully you can help me quick, I am wanting to put a 2013 GT/ GT500 front bumper and headlights on my 2005-2009 GT, (change it from the newer look from the older look), I am just wondering if this would work given the year difference i.e change in headlights and bumper... thank you looking forward to the response!
great video
is the 2010 gt almost the same?
Exactly what I needed. Clear, and simple. Thanks man.
Great Video My Guy 👌👌
Great video I was just about to change my lights on my "manstang" and stumbled across this video.. saves me a whole lot of money. Great job.! Bravo! Ty very much!
Do you have an installation video?
Great video Thank you.
Can you do more videos with s197 13-14 ! Thank you and great video too keep it up.
I’m so screwed. The screws at 3:08 for me are all rusted. I tried taking one out and it just broke. Idk what to do now.
great video. THX
awesome vid thanx
@happywrenching do you know if this bumper will fit the 2012 model ?
+angel j It will fit but you will also need a 2013+ hood.
Thank you !
@happywrenching will this work for a 2011 or 2010 if you can tell us much appreciate it.
+eddie velasquez The process is similar in that there are clips for the radiator cover at the top, clips for the bottom cover, and screws in the wheel well. The location and number of clips and screws will be slightly different than what is in this video. You will still need to unhook the fog lamps, ambient air temp sensor, and side marker lamp plugs.
+eddie velasquez The process is similar in that there are clips for the radiator cover at the top, clips for the bottom cover, and screws in the wheel well. The location and number of clips and screws will be slightly different than what is in this video. You will still need to unhook the fog lamps, ambient air temp sensor, and side marker lamp plugs.
happywrenching well thank you for commenting i do appreciate it. I am looking forward for you to do more mustangs and other sport or muscle cars.
Today I backed out of a driveway with a steep curb and the bottom of the bumper cover hit and my passenger side of the bumper cover is popped out a little ( like at 5:14). I pushed it back on but the very corner ( like where your left hand is) stays stuck out some. It's cosmetic but it aggravates me bc I only have 3K miles on my car. What holds the very end of the cover on? Is it a clip that maybe broke? I can't tell by looking at it..
Yeah its clipped in. If you look at 4:58 you will see a tab. That goes over a hook. Most likely you either broke the hook or the tab itself.
Oh yea i see.. I will have to look tomorrow when it's light out. I don't remember seeing that earlier when it was light out though. :( I guess I will have to get an entire new bumper cover all bc that one little piece is broken..ugh :(..Thanks for the quick reply though man.
I wish you had a turbo v6 mustang to show where to put a mishimoto z line universal intercooler
Believe me, I wish that too. Haha. One of these days....
What are the clips called that holds the bumper to the fender
They are usually just called bumper cover brackets.
hi i wanna thank u for showing this, im installing a 2013 mustang bumper cover on my 2011 mustang and im missing some parts now i know what they are, i also would love for u to show how the grill is installed because i have the grill but it just falls through the bumper cover there must be a support behind the grill could u show this i would really appreciate this, thank sincerely ryan
If I had the car I would definitely do a video but sadly I don't. However, there are many videos on grille installation so I'm sure you can find one that will help you.
Hey man throw back to when u wrote this post 7 years ago lol... Hopefully you can help me quick, I am wanting to put a 2013 GT/ GT500 front bumper and headlights on my 2005-2009 GT, (change it from the newer look from the older look), I am just wondering if this would work given the year difference i.e change in headlights and bumper... thank you looking forward to the response!
at 3:30 its 7mm the oil pan ones are 8mm
Awesome video very informative but why does Ford have to make it have 100 different size bolts just to take the bumper off😂
Literally struggling with ordering the right hardware from my not so local Ford deal, fml that they can’t even answer how many of each your car uses despite having a VIN.