AXBB-E Ethernet CNC Controller #1 Basic Setup
Vložit
- čas přidán 26. 07. 2024
- AXBB-E is an Ethernet CNC controller. The software it uses is UCCNC but it supports MACH3 and MACH4. It can control up to 6 CNC axes and it's stepping frequency is at its max 400kHz. It supports also rigid tapping with use of incremental encoders.
It supports servos and stepper motors which can be controlled by step/dir signals. The ethernet connection should provide electric noise protection for the machine.
Can't wait to test this guy in action!
Here is the controller and the breakout board seen in video:
👉 cncdrive.com/AXBB.html
👉 cncdrive.com/downloads/AXBB_E...
👉 cncdrive.com/UCSB.html
👉 cncdrive.com/downloads/UCSB_m...
AXBB-E and UCCNC related videos:
AXBB-E - Basic Setup 👉 • AXBB-E Ethernet CNC Co...
If you find my channel interesting or helpful - you can consider becoming my Patron on Patreon.com or a Member of my CZcams Channel Support!
Subscribe and hit the like button if you like the video and want more!
👉 / gbwm
👉 / @gbwm_cnc
Questions? - Comment down below.
Thanks for watching!
CNC Conversion of a Milling Machine: 👉 • CNC Conversion - Manua...
Milling Machine Restoration: 👉 • FUS 200 Universal Mill...
DIY CNC Metal Lathe Build: 👉 • DIY CNC Metal Lathe Build
Machine Builds: 👉 • Machine Builds (full v...
CNC Videos: 👉 • CNC
Welding Videos: 👉 • Welding
DIY: 👉 • DIY HowTo
AXBB-E/UCCNC: 👉 • AXBB-E
Facebook Page 👉 / gbwmcnc
CZcams Channel 👉 / gbwmweldingmachiningcnc
Twitter 👉 / gbwm6
Instagram 👉 / gbwm_cnc
Tumblr 👉 / gbwm-cnc
TikTok 👉 tiktok.com/@gbwm_cnc - Věda a technologie
Hello. A big thankyou to you Sir.
Because of your videos I was able to get everything working on the AXBB-E board.
I'd previously purchased an NVEM 4 axis board and had that a few years, but it was totally unreliable.
So yes .... Thankyou.
Hi! i'm so glad it helped you :)
Hi! Thank you so much for this video series! Quick question, do you know what the TCPIP command to home and go to an absolute position would be? I want to send those commands from an android device. So much gratitude for the content you post!
No idea - I had no opportunity to test such things. But I'm glad my content helped! :)
hello, could you please tell me if the controller is supporting the backlash compensation and if you have to purchase separatly the uccnc license or you get it with the AXBB-E
?
Hello. This controller supports backlash compensation. You have to buy the license seperatly but it is quite cheap compared (like $50 or so). So compared to MACH3 it seems to be much cheaper. Also the controller works with MACH3/4 too if you have that license already.
Thanks for the info.
You're welcome! Thanks for watching! 😁
Hi, would you be able to put up a quick parts list (with part/brand names) when it comes to the wiring and quick detach connectors you used? Also, I have the same PSUs and was wondering if you directly plugged them into a 110 V AC source. They are rated for 100 V - 240 V, but you mentioned connecting them to your PC first, so I wasn't sure where you connected the PSU input to. I don't want to damage them.
The quick connectors are "wago" connectors. About the devices - it's a axbb-e controller. What else exactly do you need? There is a lot of informations on my channel about the things I build. About the PSUs - I plugged them directly to 230V AC (this is the power source we have here). The PC was connected just to the controller. The PC contains the software which communicates with the controller to make the motion on the machine. If you're new to this - I think you can get quite a bit informations on my channel or similar channels over here! :)
Hi, thanks for the very informative video. I was wondering if you could show more about the diy pc control box and if you had any wiring diagrams from the build that you would share. Thanks again
Hi! I've shared all wiring diagrams and drawings I made for my machine with my CZcams and Patreon supporters. There is a video on this channel where I'm making this diy pc control box so you can check it out on my channel. If there are still informations the videos are lacking - let me know. Maybe I will make a more detailed videos in the future.
Thank you, i will check them out
Does this controller work with a USB to Ethernet cable? My laptop doesn't have an ethernet port. Also does this controller support RS485 for VFD control?
Umm, I have no answer for these questions. But there is a manual available on cncdrive.com for this controller - you might find the answer there
Wlasnie kupilem ta plytke i pozostala elektronike, jakie rodzaje/ grubosci kabla zalecasz do poszczegolnych polaczen 5v 24 v itd
Bede wdziwczny za odpowiedź
Ja w swojej frezarce wszystkie połączenia sygnałowe poprowadziłem w środku przewodami 0,5mm^2. Poza skrzynką używałem np. dla krańcówek i innych sygnałów kabli LIYCY - też o przekroju 0,5mm^2. Do tego są one ekranowane co zapobiega zakłóceniom. Póki co działa :)
Jest jakaś różnica w połączeniu między zwykłym kablem a crossover'owym?
Kwestia tego, że aby połączyć zwykłym to musi być po drodze jakiś router / switch. Tzn wpinamy sterownik do switcha / routera i komputer też wpinamy do switcha / routera. No i parę szczegółów potem w kwestii ustawień. Kablem crossover'owym podłączamy bezpośrednio sterownik bezpośrednio do komputera (czyli to co zrobiłem na filmie) . W samym działaniu nie powinno być różnicy.
The AXBB_E manual says: The signal full scale voltage range is selectable
between 0-10 Volts when the J1 jumper is off and 0-5 Volts when J1 jumper is on.
Yes. I think there is a mistake as it worked the opposite for me. Or I did something wrong 😁
Huh, I never thought about using Wagos in machines. I have enough of them in my walls and breaker box, lol.
It was just for test purposes though
@@GBWM_CNC I have the 221 box package. 4/6mm variants from 2-5 hole.
They'll be nice for 48-230v :)
@@FlyingDropBearAU if it fits the cables - why not. But anyway I use these usually for temporary setups :)
Excuse me but I have any problem. I tried to connect axbb-e controller to my eeepc 1000h asus with a crossover ethernet cable made by me but nothing. The link LED is off and the two LED of ready and 24v are ok. I tried to pull the reset bottom but nothing. Please help me!
There might be an issue with the cable. I had a similar problem - there was no connection between the PC and the controller because the RJ45 connector had a factory issue. Pressing a new connector on one end of the cable fixed the issue. You can also try the straight cable method with an switch / router between the PC and controller.
@@GBWM_CNC thank you very much for your help. I bought from Amazon a crossover cable and I will try with it.
@@stefanogobetto9897 hope it will help!
@@GBWM_CNC I will inform you! I hope in good.
Solved! With the new crossower cable is ok. Thank for your help!
I'm confused, I thought you don't need a pc to use uccnc?
No. You need a PC or laptop with windows for UCCNC. Similar as mach3. You can run the AXBB-E with mach3/mach4 too (need plugin for that).
Masso is the only one i know that doesn't require a pc to run.
It seems to me UC400ETH controller is much better option than AXBB-E as the first one can be shared between many machines whereas the latter one cannot.
Could you expand what do you have on mind? How could be one of these shared between machines and the other not? Like disassembling and assembling it between machines? This would be annoying I guess :D
Kiedy następny odcinek o AXBB-E?
Dziś tylko muszę znaleźć czas na zrobienie napisów 😁
@@GBWM_CNC Good job mister GBWM
Will it work with linuxcnc?
Only mach3 /mach4 /uccnc
Interesting series of videos, but if possible, please, leave the text more time
I'll try to improve that. Thanks
@@GBWM_CNC thank you for your work for us
@@IceCreams62 I'm glad you like my work :)
Will this work in windows 11?
I didn't test it on windows 11 but I've heard people use it with win11. If you want to be sure - ask on cncdrive.com
@@GBWM_CNC thank you 😊
대중적이지 않다. 광고가 아닌 이상 쉽게 구해쓰는걸 보여주기 바란다. .
DIY의 궁극적인것은 상용에 버금가거나 기술적 한계로 상용의 메너리즘을 뛰어 넘는거라고 본다. ..
컨트롤러의 실제 사용 방법과 사용법(스핀들, cnc 축, 리지드 엔코더 등의 설정)에 대한 동영상을 제작하겠습니다. 다른 비교적 저렴한 컨트롤러와 비교하여 이 컨트롤러는 LPT/병렬 포트 대신 이더넷 연결, 견고한 태핑, 고주파수 및 확장 및 프로그래밍할 수 있는 많은 입력 및 출력을 포함하여 실제로 기능이 있는 것 같습니다. 지금 만들고 있는 기계와 함께 사용할 것이므로 좋은 예가 될 것입니다. 댓글 감사합니다 😁
@@GBWM_CNC 늘 영상을 보면서 같은 고민울 하고 있다는걸 느낀다. 서보모터로 넘어간 이상 분해능과 가감속 페턴, 충돌방지와 회피의 작업 포스트면 굵은 골자는 끝이지만, 기초적인 스텝모터에도 상당한 능력이 부여할수 있음을 생각할떼, pc사양과 노이즈를 회피하는 노하우가 꼭 필요하다.
그리고 초보자둘도 쉽게 모델링후 cam에 무료로 쓸수 있는 언정적 소프트웨어의 추천을 바란다. 마하3을 기반으로 쓸수 있는것들을 영상보며 배워보고 해보고 싶다.
@@Hydra.1005 이 컨트롤러를 사용하여 더 자세한 비디오를 만들려고 노력할 것입니다. 이 컨트롤러는 MACH3 및 MACH4를 지원하지만 제조업체 소프트웨어인 UCCNC는 사용하기 쉽고 투명합니다. MACH3 대신 시도해 보겠습니다. 그러나 전반적으로 UCCNC 소프트웨어는 MACH3(신선하고 더 현대적임)와 매우 유사하므로 여러분도 무언가를 배울 수 있어야 합니다! :) CAM 소프트웨어가 필요한 경우 Fusion360을 사용해 보는 것이 좋습니다. 개인적인 사용을 위해 그것의 무료 소프트웨어와 아주 잘 작동합니다.
@@GBWM_CNC I apologize that I pretended to know for nothing and that I confused mind. I apologize for not respecting your time. However, I hope that even beginners will have enough room to follow. I was presumptuous. And I'll be more careful
Stupid way to post something without talking