Thank you for helping people in this predicament! I have a 09 challenger that I replaced the abs module in and went through all Intialization tests then scan froze and ABS light and beeping began. Upon driving home from mall parking lot brake, bas esp eng lights cleared up! Now I m stuck with this constant beeping & abs light blinking! The dealer says you have to have new module flashed to clear the blinking & beeping! Of course this could take a day up to a week before they could get to it and price of flashing is $160 ! I think I’m gonna try your method 1st! $55 sounds a lot better to me!
My Jeep would do the same exact beeping and flashing on the dash. It took me about 5 tries to get the initialization to complete successfully. Sometimes the flashing process is just a bit picky!
I'm thinking about sending mine off and having it repaired since finding one will be hard. If I send my module off can I still drive the jeep until module comes back in? I'm glad I found your video I've been trying to find out about jscan flashing it.
Removing the ABS module will cause the loss of ABS, ESP, BAS, and ERM. Additionally, your speedometer will stop working and the automatic transmission stops shifting because it needs a Vehicle Speed Signal which is generated by the ABS module in coordination with your wheel speed sensors. Overall, it is highly not recommended to operate the vehicle without an ABS module. Sending in your ABS module for repair is good alternative however you need to be ready to have the Jeep inoperable while the module is getting repaired. On the bright side, I have heard that you do not have to re-program or flash the module if it is only repaired. If the Jeep still drives and you absolutely need it as your daily driver, I would recommend getting a new module and wait it out so you don’t lose your transportation. Hope this helps, and yes it sucks. I had to drive for 8 months with all my lights on until I received my module.
Hi, I have a jeep wrangler Sahara 12 my problems is I have the engine light on and it get hot don’t give me the 3er speed I know I have one abs sensore bad what can be…?
Hey, I recommend scanning your car first to see what trouble codes you have. That should point you in the right direction. If your cars overheating I would check for any leaks, bad thermostat, or air trapped in the system. Good luck
Thank you for helping people in this predicament! I have a 09 challenger that I replaced the abs module in and went through all Intialization tests then scan froze and ABS light and beeping began. Upon driving home from mall parking lot brake, bas esp eng lights cleared up! Now I m stuck with this constant beeping & abs light blinking! The dealer says you have to have new module flashed to clear the blinking & beeping! Of course this could take a day up to a week before they could get to it and price of flashing is $160 ! I think I’m gonna try your method 1st! $55 sounds a lot better to me!
My Jeep would do the same exact beeping and flashing on the dash. It took me about 5 tries to get the initialization to complete successfully. Sometimes the flashing process is just a bit picky!
Sir this is one of the best avs JScan video 😊thank you for sharing for your knowledge and expertise
Glad you liked it
thank you for the information, very informative
Awesome video bro!! I’m having the same issue with my 09 jku.
Thank you bro! I don’t know what I would do without JScan !
I'm thinking about sending mine off and having it repaired since finding one will be hard. If I send my module off can I still drive the jeep until module comes back in? I'm glad I found your video I've been trying to find out about jscan flashing it.
Removing the ABS module will cause the loss of ABS, ESP, BAS, and ERM. Additionally, your speedometer will stop working and the automatic transmission stops shifting because it needs a Vehicle Speed Signal which is generated by the ABS module in coordination with your wheel speed sensors. Overall, it is highly not recommended to operate the vehicle without an ABS module. Sending in your ABS module for repair is good alternative however you need to be ready to have the Jeep inoperable while the module is getting repaired. On the bright side, I have heard that you do not have to re-program or flash the module if it is only repaired. If the Jeep still drives and you absolutely need it as your daily driver, I would recommend getting a new module and wait it out so you don’t lose your transportation. Hope this helps, and yes it sucks. I had to drive for 8 months with all my lights on until I received my module.
Great video ! I’m sending one off to have it remapped.
Hi, I have a jeep wrangler Sahara 12 my problems is I have the engine light on and it get hot don’t give me the 3er speed I know I have one abs sensore bad what can be…?
Hey, I recommend scanning your car first to see what trouble codes you have. That should point you in the right direction. If your cars overheating I would check for any leaks, bad thermostat, or air trapped in the system. Good luck
what year is this ?
Great question! My jeep is a 2011.
Did this bad abs affect your speedometer from working
Thanks if you have time to answer
Got a U1412 error code after programming my new module.