Video

you build your roll cage or bought it? if bought where you get it

You need two twin choke down draught weber carburettors and short manifolds to make it go good.

This vedeo was to sell the idea

Would you see there was the result of the lawsuit because they went from stick to a T form of steering which was from my belief hydraulic steering with the steering wheel instead of stick like a bulldozer

Do you know how much you can sell them fixed and cleaned up

I completed the conversion today thanks to your kit, it runs way better than it ever did with the solex on it, setting up the fuel system was probably the hardest part.

very detailed video. Did you decode your EPS to work or it worked straight up? I got the same one but I had to decode it. well done

The real question is how we're gonna get my own out to Annapolis/DC to take Dad for a spin.

Did you rebuild the engine?

Russian components.. American components.. All made in TAIWAN! 🇹🇼

how much did you pay for that in the salvage yard?

great job!!!

I have one for sale in iowa

aight its been 3 years, we need an update

Can you tell me what gage wires are required for a 12 volt system (converted from 6 volt) 1953 cj3b

Can you tell me what gage wires are required for a 12 volt system (converted from 6 volt) 1953 cj3b

I had a dream where I was driving one of these in the country, best dream ever.

U guys need winches on the front of those jeeps

i would mount a winch on the front of the jeeps good back up !

Painting without sandblasting!?????? No

Far out grease those bearings dude

That is so cool jeeps can do anything

I recently converted my 52 M38 to a 12V and the used the Kaiser Willy’s kit. Your correct the bracket is trash and I’ll be ordering the bracket you have shown in the video. Cannot get my pulley to align properly enough to stop it from squealing when the engine is running.

I looks like a standard Willyes, but this is not a standard Willys.

Does anyone know the exact length of a jeep, without the bumpers and spare wheel attachment? basically the tub + the hood

Does anyone know the exact length of a ww2 jeep, without the bumpers and spare wheel attachment? basically the tub + the hood

Bagus dengan model militer...👍

9:59 Turley mental

Did you do the cutting of the bus or did you hire someome?

The alternator output curve is not linear. You can get enough amperage at a fast idle with a 10si. Your belt may be holding you back but the L134 had a generator and a 5” crank pulley. You could try a smaller pulley but measure them, the shaft speed needs to be about 2500rpm at a idle and you are aiming at more than 50% of the load at idled. The crank pulley is about 5” diameter, the alternator pulley 2.5”. That is a pulley ratio of PI x D or 200% difference. A fast idle of 1250 rpm should give you 2500rpm shaft speed. You need to measure and then buy an alternator pulley, which are cheap. Cars generally have a pulley ratio of 3 which means an alternator pulley of 1.75”. Measure it. I have a smaller Mitsubishi alternator and it runs fine with correct tension. www.billavista.com/tech/Articles/Alternator_Bible/images/10si%20perf%20curves.jpg

Nice

Super cool video!

Hello, the handbrakes?????

Is a beautiful

The words “Harbor Freight” and “don’t last very long” are frequently used in the same sentence. Nice “Cobra Stinger” Willy Jeep

Nice jeep

I know how it smells in that garage

Oh, and great video, thanks

Where did you find a wheel drum puller?

😭

Are you still selling these jeeps?

Can you ask the AM General gentlemen to share the status of the factory toolings to make the M151A2 after the termination of production ? Like those stamp machines to make the tub etc... That would be of great value to the M151A2 community. Thank you very much.

Como debe ser la ingenieria de esta máquina és genial.

nice work. a clean large space, access to good tools and large equipment no doubt makes restorations like this easier, of course along with know how and vision.

If you said it I missed it. Where does the alternator plug into?

Need to turbo that thing and install an exhaust pipe

Oh lord jr….. you coulda got all the bolts out without breaking if you woulda heated them up red hot with a torch and hitting them with air to cool them quickly

Amazing Find 👍 Wow 😮

Who is paying for all this?

Great video! Not much I can say that hasn't been said, but.....I can't believe nobody has commented on the tiny trailers brought them on!?! Well played!